Assembly Instructions

ManualsBrandsMasterforce ManualsPower Tool AccessoriesUniversal Folding Miter Saw Stand

[A J

Miter Saw Workstation

240-1658

Customer Service: 1-800-255-7011

OPERATOR’S MANUAL

CAUTION:

To Reduce The Risk Of Injury, User Must Read And

Understand Operator’s Manual. Save These Instructions For Future Reference.

Summary of content (16 pages)

PAGE 1
Miter Saw Workstation 240-1658 Customer Service: 1-800-255-7011 OPERATOR’S MANUAL [ACAUTION: JTo Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference.
PAGE 2
TABLE OF CONTENTS Safety.......................................................................................................................Page 2 Features.................................................................................................................. Page 3 Overview................................................................................................................. Page 3 Parts List.............................................................................................
PAGE 3
SAFETY SAFETY WARNING WARNING: Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION” before using this power tool accessory. Failure to follow all instructions listed in the manual may result in electric shock, fire and/or serious personal injury. GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS Using power tools of any kind can be dangerous if safe operating procedures are not followed.
PAGE 4
FEATURES Your Miter Saw Workstation is loaded with standard features all designed and engineered to maximize the functionality and flexibility of your Miter Saw Workstation. STANDARD FEATURES • Rapid Clamp Tool Mounts • Adjustable Material Supports • Wheels for easy transportation OVERVIEW Figure 1 You have just purchased a Miter Saw Workstation.
PAGE 5
PARTS LIST PART # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 DESCRIPTION QTY MITER SAW WORKSTATION 1 pc RAPID CLAMP TOOL MOUNT 2 pcs OFFSET MOUNTING BRACKET 2 pcs WIDE MATERIAL SUPPORT 4 pcs WORK STOP 4 pcs MATERIAL SUPPORT RECEIVER 4 pcs WHEEL 2 pcs AXLE 2 pcs HANDLE 1 pc KNOB SCREW 4 pcs KNOB NUT 4 pcs CORD MINDER ATTACHMENT 2 pcs CARRIAGE BOLT M6*55 4 pcs CARRIAGE BOLT M8*20 6 pcs NUT M8 12 pcs 1 7 12 26 14 20 27 21 28 QTY 4 pcs 12 pcs WASHER M8 17 12 pcs SPRING WAS
PAGE 6
ASSEMBLY INSTRUCTIONS Read all assembly instructions completely before attempting assembly. ATTACHING THE WHEELS Figure 2 1. Extend the legs by depressing the leg lock levers. 2. Insert (8) axle through the mounting bracket and make sure the flat of the axle is inserted into the flat of the inside of the mounting bracket. 3. Tighten (24) M10 nylon nut to the inner threaded portion of the axle. 4. Place (27) M12 washer then the (7) wheel onto the outer portion of the axle. 5.
PAGE 7
ASSEMBLY INSTRUCTIONS FIG 3 Handle M8*20 Bolt Spring Washer Flat Washer Nut M8 PREPARING THE STAND Figure 4 1. Grab the (9) handle of the stand so that the wheels are on the ground and supporting the weight of the stand. 2. Press the Quick Release Leg Lock Lever on one of the legs on the side of the handle and rotate the leg downward until the locking pin clicks into place. 3. Repeat with the other leg on the side of the handle. 4.
PAGE 8
ASSEMBLY INSTRUCTIONS ASSEMBLING AND INSTALLING MATERIAL WORK SUPPORTS Figure 5 1. Slide one (13) M6*55 carriage bolt through the square hole in the (4) wide material support and extend through the other side. 2. Place the (5) work stop over the end of the bolt. 3. Thread one (11) knob nut over the end of the bolt and tighten to secure. 4. Slide the wide material support rail through the hole in the top of the (6) material support receiver. 5.
PAGE 9
ASSEMBLY INSTRUCTIONS ASSEMBLING RAPID CLAMP TOOL MOUNTS Figure 6 1. Lay out all parts before starting the assembly process. 2. Select one (21) storage handle and position it where desired on one (2) Rapid Clamp Tool Mounting Rail. Run two (14) M8*20 carriage bolts through the slots in the rail arms and attach using a (17) M8 washer and nut. These handles are designed to store tools and can be located where most convenient for the user by sliding it along the rail. See Figure 6.
PAGE 10
ASSEMBLY INSTRUCTIONS ATTACHING THE BUCKET HANGER Figure 7 1. Place (28) bucket hanger hoop over the central tubing. 2. Feed (30) M5*47 bolt through cord snap then through the bucket hanger. 3. Apply (25) M5 Nylon nut and tighten. - ~ FIG 7 M5 Nylon Nut M5*47 Screw Bucket Hanger ATTACHING YOUR MITER SAW OR OTHER BENCHTOP POWER TOOL Figure 8 Various bench top tools can be used with your Miter Saw Workstation by attaching them to the Rapid Clamp Tool Mounts.
PAGE 11
ASSEMBLY INSTRUCTIONS OFFSET MOUNTING Figure 9 Offset mounting bracket for miter saws and/or power tools with an irregular mounting hole pattern. Instructions: Secure (3) offset mounting brackets as shown using the supplied (16) M8*60 carriage bolts. These brackets can be used on the front or rear of the rapid clamp tool mounts to accommodate your specific power tool. - FIG 9 Offset Mounting Brackets ATTACHING CORD MINDER Figure 10 1. Locate leg with 2 pass-through holes. (handle side) 2.
PAGE 12
ASSEMBLY INSTRUCTIONS MOUNTING THE MITER SAW TO THE STAND Figure 11 Use the handles located at the rear of the tool mounts to aid in installing or removing saw and tool mount assembly. 1. Lift the saw and tool mount assembly, allowing the assembly to tilt slightly toward your body. 2. While still tilted toward you, hook the front edge of the tool mount assembly onto the front rail of the stand. 3. Lower the tool mount assembly to allow the rear edge of the tool mount to seat fully over the rear rail. 4.
PAGE 13
ASSEMBLY INSTRUCTIONS TO REMOVE SAW FROM STAND Figure 12 1. Raise the locking levers to unlock the saw and tool mounts. 2. Unsnap the J-Lock™ clips from around the mounting beams to allow your tool to separate from your MASTERFORCE® Miter Saw Workstation. 3. Lift away from the rear rail of the stand to disengage. 4. With the assembly tilted slightly toward you, lift the assembly to disengage from the front rail of the Miter Saw Workstation. - FIG 12 TRANSPORTING AND STORING Figure 13 1.
PAGE 14
ASSEMBLY INSTRUCTIONS TOOL MOUNT ADJUSTMENT SCREW Most plastic tool mounts are designed to fit snugly over the stand rails. With the locking levers in the lowered (locked) position, you should not be able to remove the saw and tool mount assembly from the rails. If the saw and tool mount can be removed from the rails when the levers are locked, the tool mount adjustment screws need to be tightened.
PAGE 15
Miter Saw Workstation WARRANTY 90-DAY MONEY BACK GUARANTEE This MASTERFORCE® brand tool carries our 90-Day Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund - no questions asked.