Miter Saw Stand 240-1657 Customer Service: 1-800-255-7011 OPERATOR’S MANUAL [ACAUTION: JTo Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference.
TABLE OF CONTENTS Safety.......................................................................................................................Page 2 Features...................................................................................................................Page 3 Overview................................................................................................................. Page 3 Parts List.............................................................................................
SAFETY SAFETY WARNING WARNING: Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION”, before using this power tool accessory. Failure to follow all instructions listed in the manual may result in electric shock, fire and/or serious personal injury. GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS Using power tools of any kind can be dangerous if safe operating procedures are not followed.
FEATURES Your Miter Saw Stand is loaded with standard features all designed and engineered to maximize the functionality and flexibility of your Miter Saw Stand. STANDARD FEATURES • Rapid Clamp Tool Mounts • Adjustable Material Supports • Wheels for easy transportation OVERVIEW Figure 1 You have just purchased a Miter Saw Stand.
PARTS LIST PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 QTY MITER SAW STAND 1 pc RAPID CLAMP TOOL MOUNT 2 pcs OFFSET MOUNTING BRACKETS 2 pcs MATERIAL SUPPORT 2 pcs WORK STOP 2 pcs MATERIAL SUPPORT RECEIVER 2 pcs WHEEL 2 pcs AXLE 2 pcs HANDLE 1 pc KNOB SCREW 2 pcs KNOB NUT 2 pcs CORD MINDER ATTACHMENT 2 pcs CARRIAGE BOLT M6*55 2 pcs PART # .
ASSEMBLY INSTRUCTIONS Read all assembly instructions completely before attempting assembly. ATTACHING THE WHEELS Figure 2 1. Extend the legs by depressing the leg lock levers. 2. Insert (8) axle through the mounting bracket and make sure the flat of the axle is inserted into the flat of the inside of the mounting bracket. 3. Tighten (24) M10 nylon nut to the inner threaded portion of the axle. 4. Place (26) M10 washer then the (7) wheel onto the outer portion of the axle. 5.
ASSEMBLY INSTRUCTIONS ATTACHING THE PULL HANDLE Figure 3 1. Place one (18) spring washer and one (17) M8 washer onto (19) M8*20 bolt. 2. Place (19) M8*20 bolt through the back of the holes in the body as shown in Figure 3. 3. Place one (15) M8 nut into the square slot on the bottom of the handle. 4. Pass the bolt through the handle and use one hand to hold the handle and nut into position and the other hand to tighten the bolt. 5. Repeat steps 1-4 for the other side of the handle. 6.
ASSEMBLY INSTRUCTIONS PREPARING THE STAND Figure 4. 1. Grab the (9) handle of the stand so that the wheels are on the ground and supporting the weight of the stand. 2. Press the Quick Release Leg Lock Lever on one of the legs on the side of the handle and rotate the leg downward until the locking pin clicks into place. 3. Repeat with the other leg on the side of the handle. 4. Lift the stand on the side with the wheels so that the weight is supported by the user and the already opened legs. 5.
ASSEMBLY INSTRUCTIONS - FIG 5 Work Stop Knob Nut Material Support Receiver Material Support ~ Knob Screw Knob Nut Knob Nut Knob Screw Small Screw Extension Rail Small Screw Handle ASSEMBLING RAPID CLAMP TOOL MOUNTS Figure 6 1. Lay out all parts before starting the assembly process. 2. Select one (21) storage handle and position it where desired on one Rapid Clamp Tool Mount rail. Run two (14) M8*20 Carriage bolts through the slots in the rail arms and attach using a (17) M8 washer and nut.
ASSEMBLY INSTRUCTIONS 5. Tighten down the (15) M8 nuts that were placed in the rapid clamp tool mounting rail and rapid clamp tool mount base in Step 3. 6. The rapid clamp tool handle and tool storage arms can be placed anywhere along the Rapid Clamp Tool Mounting Rail. Hold the rapid clamp tool handle and tool storage arms in place using two (14) M8*20 carriage bolts and two (15) M8 nuts.
ASSEMBLY INSTRUCTIONS 3. Feed one (16) M8*60 carriage bolt up through both the tool mount and a mounting hole in the saw. 4. Secure in place using a (17) flat washer, (18) spring washer, and (15) M8 nut. 5. Repeat through the other end of the tool mount. 6. Place the second tool mount underneath the other side of the saw, aligning the mounting holes on the miter saw base with the opening in the tool mount. 7. Install (16) M8*60 carriage bolts as previously described. 8.
ASSEMBLY INSTRUCTIONS ATTACHING CORD MINDER Figure 9. 1. Locate leg with 2 pass-through holes. 2. Pass one (23) M5*55 screw through the top hole of the leg and through the (12) plastic cord minder attachment, making sure that the tip of the cord minder attachment is pointing up towards the top of the stand. 3. Apply (25) M5 nylon nut and tighten. 4.
ASSEMBLY INSTRUCTIONS FIG 10 J-Lock™ Clip NOTE: Continue to hold the tool mount assembly with one hand until both levers are securely locked. 6. Check position and adjust if necessary to make sure the weight of the saw is evenly balanced over the rails. 7. Ensure the saw is seated and locked in position, then securely tighten the four nuts holding the saw to the tool mounts. TO REMOVE SAW FROM STAND Figure 11 1. Raise the locking levers to unlock the saw and tool mounts. 2.
- ASSEMBLY INSTRUCTIONS FIG 11 TRANSPORTING AND STORING Figure 12 1. Before storing or transporting, make sure all attachments are secure and bench top tool is removed. 2. Collapse legs and make sure they are locked into the up position. 3. Use the (9) handle that is located on the end of the product for transporting. 4. Pull up on the handle and tilt Miter Saw Stand until weight is distributed evenly onto wheels.
ASSEMBLY INSTRUCTIONS TOOL MOUNT ADJUSTMENT SCREW Most plastic tool mounts are designed to fit snugly over the stand rails. With the locking levers in the lowered (locked) position, you should not be able to remove the saw and tool mount assembly from the rails. If the saw and tool mount can be removed from the rails when the levers are locked, the tool mount adjustment screws need to be tightened.
NOTES Page 15
NOTES Page 16
NOTES Page 17
Miter Saw Stand WARRANTY 90-DAY MONEY BACK GUARANTEE This MASTERFORCE® brand tool carries our 90-Day Money Back Guarantee. If you are not completely satisfied with your MASTERFORCE® brand tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund - no questions asked.
; z . E C R J i i l m T 5 /M" © 2019 Menard, Inc.
