Specifications: Active Loudspeaker Specifications Powered Wireless loudspeaker system Texas Instruments DSP & Class D amplification Wireless Solution – STS technology (SMSC) Rear firing reflex port Amplifier WS90t Features: - Built in wireless receiver in each speaker - Wireless signal range up to 25 meters, 50 meters line of sight. - No interference or delays - Audio Latency 18ms (max) - Works with PC and Mac - Use any source with “line out” Analogue "optical" digital - In/output via 3.
What's in the box? 1 x Remote control 1 x Pair active loudspeakers – dedicated left and right speaker 2 x Power cords 1 x Line out cable(RCA – mini jack) 1 x Wireless transmitter 1 x UK adapter (for wireless Transmitter where line out is used) 1 x 3.5mm Mini Jack cable (3.5mm mini jack – 3.5mm mini jack) The loudspeakers are covered with a soft faux leather material. Please take care when unpacking the speakers to avoid scratching or indenting the material.
Getting Started Place the speakers in your preferred position but within reach of wall sockets. Left and Right speakers can be identified by looking at the rear of the cabinet. With the mains socket in the OFF position, connect the a/ c lead to the speakers using only the supplied mains leads and power supplies. Turn the mains socket ON. To use your speakers with a PC or MAC MAC set-up 1.Insert the USB connector from the transmitter to a free USB socket on your MAC. 2.
Wireless Status When the transmitter is connected to a source device the LED will flash intermittently When the speakers are connected to mains power the LED on the front of the speaker will light up for 3 seconds then power off. Using the remote control, aim at the one of the speakers and press the Power On button.
To use your speakers with MP3 devices (headphone out) Plug one end of the supplied 3.5mm mini jack lead into the transmitter and the other end into the headphone socket on your device. Plug the USB connector from the transmitter into the mains adapter and plug the mains adapter into a convenient wall socket and turn on. Push the button in the centre of the transmitter to select a free zone. Using the remote control press the “station” button” to find the signal from the new source equipment. ….
Remote control Page | 6 Power on/off VOL- Mute Skip Station Back skip VOL+ Play/pause
Rear Panel Power STATION Switch station by pressing this button ZONE SWITCH Switch zone by lever switch Page | 7
Multi-Zone Function The WS90ti system is factory set to default mode. In default mode; If more WS90t’s are added to the network, the remote will control all speakers within the network simultaneously, if within transmitter range. By using the multi zone feature on the remote control, volume and source selection can be independently controlled for each zone. The same source device serving different zones.
Product Registration (address on back cover) Model Serial Number Date of purchase Customer details Name Address line 1 Address line 2 Town Country Postcode/zip code Telephone Dealer details Dealer name Address line 1 Address line 2 Town County Postcode Country Page | 9
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFETY INSTRUCTIONS 13. Damage Requiring Service D If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation. E. If the apparatus has been dropped or damaged in any way, and. F.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Requirements (MPE) To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que l a popul ation ne puisse y être exposée à une distance de moin de 20 cm.
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à l a réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émet teur par Industrie Canada.
THIS DEVICE COMPLIES WITH INDUSTRY CANADA LICENCE-EXEMPT RSS-210 STANDARDS. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION OF THE DEVICE. LE PRÉSENT APPAREIL EST CONFORME AUX CNR-210 D'INDUSTRIE CANADA APPLICABLES AUX APPAREILS RADIO EXEMPTS DE LICENCE.
Blue Aura Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Blue Aura distributor provided that it was originally purchased from an authorised Blue Aura dealer or distributor.