O W N E R ’ S M A N U A L
T R E A D M I L L
Table of Contents 1.0) 1.1) 1.2) 1.3) 2.0) 2.1) 2.2) 2.3) 3.0) 3.1) 3.2) 3.3) 3.4) 3.5) 3.6) 3.7) 4.0) 4.1) 4.2) 4.3) 5.0) 5.1) 5.
1) Important Safety Information It is the sole responsibility of the purchaser of Matrix Fitness Systems products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment. DANGER To reduce the risk of electric shock: • Always unplug this equipment from the electrical outlet immediately after using and before cleaning.
1) Important Safety Information 1.2 ELECTRICAL REQUIREMENTS 1 2 0 V U N I T S D E S I G N AT E D F O R U . S . M A R K E T S For your safety and treadmill performance, Matrix Fitness Systems' treadmills require a dedicated 20 amp circuit. The ground on this circuit must be non-looped. Please refer to NEC article 210-21 and 210-23. Your Treadmill is provided with a power cord with a plug listed below and requires the listed outlet.
2) Setting Up the Treadmill 2.1 U N PA C K I N G T R E A D M I L L The users MATRIX treadmill is inspected before it is packaged. It is shipped in four pieces: the base, the uprights console supports the handlebar and the console. Carefully unpack the unit and dispose of the box material. CAUTION This unit weighs 450 pounds. Be sure to have proper assistance to remove and move the unit, to avoid injury to the user and the unit. 2.2 1. 2. 3. 4. 5. 6. 7. 8.
3) Overlay Description and Custom Settings 3.1 THE CONSOLE operator/manager to customize. Unless otherwise noted manager screens consist of the initial screen, the editing or action screen and the saving screen. The initial screen displays the variable type and in most cases the current value. Edit or actions screens are where the editing of the variable take place. The saving screen indicates the variable is being saved.
3) Overlay Description and Custom Settings This variable is editable. Numeric entry is active. Active variable displayed in the time seven segment display. Numeric entry is active. P4 DEFAULT WEIGHT (EDIT) P11 DEFAULT VOLUME (EDIT) This variable sets the default weight used in the calorie calculations. Active variable displayed in the time seven segment display. Sets to default on unit change. Displayed in native units (kilogram or pounds). Numeric entry is active.
3) Overlay Description and Custom Settings CSAFE OUT allows CSAFE products to be daisy chained together from one unit to the next. The connection is as follows: UNIT 1 CPU CSAFE IN CSAFE OUT UNIT 2 CSAFE IN CSAFE OUT 3.6 UNIT 3 CSAFE IN E N T E R TA I N M E N T D E V I C E S F O R T H E T 5 T R E A D M I L L The users equipment is preset to offer the user the maximum benefit of the users desired entertainment offering.
4) Maintenance 4.1 1. 2. 3. 4. 5. 6. 7. Locate the two hex head bolts on the rear of the treadmill. The bolts are located at each end of the frame at the back of the treadmill. These bolts adjust the rear belt roller. Do not adjust until the treadmill is on. This will prevent over tightening of one side. RECOMMENDED CLEANING TIPS STEP 1 Use a soft clean cotton cloth. DO NOT use paper towels to clean surfaces on the treadmill. Paper towels are abrasive and can scratch surfaces.
5) Using the Programs 5.1 KEYS INTRODUCTION TO THE PROGRAMS ELEVATION UP/DOWN Increases/decreases level. Value displayed in the elevation window will change when change in level for given LED’s displayed change the elevation. SPEED UP/DOWN KEYS Increases/decreases speed PROGRAM KEYS Change to selected program (except HR), displays “reset for HR” message if HR key. STOP KEY (PRESSED) Jumps to pause screen.
5) Using the Programs additional change to the workout is required the user is prompted to increase/decrease the alternate variable. START KEY Jumps to STARTING “3…2…1” screen for current program (restarts current program). AUTO ENTRY/TIME OUT Timeout after 25 seconds jumps to the safety startup screen. Pressing any key will extend the timeout time.
6) Operating the Programs 6.1 M A N U A L O P E R AT I O N MATRIX design makes using the programs as easy as one touch of a button. During Quick Start STEP 4 Select Weight by using the UP or DOWN arrow keys. STEP 5 Press START to begin workout. Treadmill will Flash “Starting 3..2..1” Then the belt will start moving. or Manual operation the Manual Run Time Screen will appear. Prepare to start and press QUICK START to begin workout. Program will use the default settings for Time and weight.
6) Operating the Programs Press ENTER or wait 5 seconds. STEP 6 Select MAXIMUM SPEED/ELEVATION by using the UP or DOWN arrow keys select the active variable Maximum Speed or Elevation that will be used to control the users heart rate.
7) Equipment Specifications >treadmill MX-T5 S P E C I F I C AT I O N S Product Name Foot Print Weight Running Area Belt Type Max User Weight Frame Construction Incline Range Speed Min Speed Max Motor Type Reliance Motor Size Controller Cooling fan Electrical Receptacle Electrical Plug Electrical Receptacle Electrical Plug Electrical Amps Electrical Amps Sharp TV Electrical Deck Wax T5 85”L x 35”W x 62”H 450 22 x 60 Habisat 400 = 181.4 kg Steel 15% 0.
8) Parts & Assembly >treadmill MX-T5
T H I S PA G E I N T E N T I O N A L LY B L A N K
8.
8.2) Parts List >treadmill MX-T5 NO.
8.2) Parts List >treadmill MX-T5 NO.
8.2) Parts List >treadmill MX-T5 NO.
8.2) Parts List >treadmill MX-T5 NO.
8.
8.
8.
8.
8.
8.
8.
M AT R I X F I T N E S S S Y S T E M S , I N C . 1 4 11 B R O A D W AY, N E A L B U Q U E R Q U E , N M 8 7 1 0 2 TOLL FREE 866.693.4863 FAX 5 0 5 . 2 4 2 . 4 7 2 5 w w w. m a t r i x - f i t n e s s .
