2 PIECE STEEL LOADING RAMPS *Actual product may vary slightly Please carefully read and save these instructions before appempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property damage and/or personal injury. Please keep instructions for future reference. For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
SPECIFICATIONS Capacity 1,000 lb. combined, 500 lb. individually (Static Conditions)* Max. Tailgate Height 36″ Dimensions 72″ L x 9″ W x 2″ H IMPORTANT SAFETY INFORMATION 1. Before use: c. if tailgate on carrying vehicle is higher than 36″, or a. Read and understand manual. d. to load vehicle with wheel width wider than ramp. b. Inspect before every use; do not use if parts loose or damaged. c. Turn vehicle’s ignition off and set parking brake. d.
21. Replacement parts and accessories When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with these ramps. 15. Wear ANSI-approved impact safety goggles, a safety helmet, and heavy -duty work gloves when loading, unloading or handling ramps. 16. Keep proper footing and balance when loading or unloading. 22.
Tongue Edge Correct Wrong SETUP AND OPERATION INSTRUCTIONS TO PREVENT SERIOUS INJURY: Before loading or unloading turn vehicle’s engine off, set its transmission in gear or park, engage its emergency brake and block its wheels. Make sure the Ramps are clean and dry before loading or unloading. Setup 1. The tailgate the ramps will sit on and both of the ramps must be dry and clean. Check for and tighten any loose hardware. 2. Sit the tongue (angled lip) of the Ramps on the tailgate.
Chain Adjustment 1. Remove the bolt and washer that hold the safety chain to the ramp. 2. Reinsert the bolt through a link that will shorten the chain so the loading ramp can not be pulled backwards more than an inch or two. 3. Make sure the washer prevents the bolt from slipping through the chain link and tighten the bolt securely. 4. Adjust the other chain to equal length. 4- Wheel ATV Loading and Unloading • These ramps are for use with 2-wheeled dirt bikes and 4-wheeled ATV’s only.
Unloading WARNING! Riding an ATV while unloading is dangerous and should not be attempted. 1. Have an assistant monitor the Ramp tongues for slippage on the tailgate. 2. Setup the ramps on the truck bed as explained under operation. Remove all tie down straps and securing equipment from the ATV. 3. While staying off the ATV, start the engine, disengage the parking brake, put the transmission into reverse, and make sure the wheels are in a straight line with the ramps.
MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY: Remove the ramps from the vehicle before performing any maintenance or service. Do not use damaged equipment. If Ramps are damaged, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the Ramps. Check for: 2. Clean the ramps after each use.
Assembly Diagram Bolt M8 x 16 (5) Tongue (2) Ramp (1) Attach Safety Chain (3) to one of the holes on the side of the ramp using an Bolt M6 x 20 (8), Nut M6 (7) and Flat Washer Ø6 (9) Flat Washer Ø8 (6) Nut M8 (4) Safety Chain (3) customerservice@focus-ontools.
Limited Manufacturer Warranty FOT makes every effort to ensure that this product meets high quality and durability standards. FOT warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.
