Datasheet

ManualsBrandsMaxbotix ManualsRobot PartsXL-MaxSonar-EZ4 High-Performance Ultrasonic Rangefinder

XL-MaxSonar

- EZ/AE™ Series

Page 1

Web: www.maxbotix.com

PD11840l

MaxBotix Inc., products are engineered and assembled in the USA.

XL-MaxSonar

- EZ™ Series

High Performance Sonar Range Finder

MB1200, MB1210, MB1220, MB1230, MB1240, MB1260, MB1261

MB1300, MB1310, MB1320, MB1330, MB1340, MB1360, MB1361

The XL-MaxSonar-EZ

series has high power output along with real-time auto sensitivity

adjustments for changing conditions (temperature, voltage and acoustic or electrical noise)

that ensure you receive the most reliable (in air) ranging data for every reading taken. The XL-MaxSonar

-EZ/AE sensors have a low power requirement of 3.3V – 5.5V and operation provides very short to long-range detection and ranging,

in a tiny and compact form factor. The MB1200 and MB1300 sensor series detects objects from 0-cm

to 765-cm (25.1 feet) or

1068cm (35 feet) (select models) and provide sonar range information from 20-cm

2,3

out to765-cm or 1068-cm (select models) with

1-cm resolution. Objects from 0-cm

to 20-cm

2,3

typically range as 20-cm

2,3

. The interface output formats included are pulse width

output (MB1200 series), real-time analog voltage envelope (MB1300 series), analog voltage output, and serial digital output.

Objects from 0-mm to 1-mm may not be detected.

For the MB1200/MB1300, MB1210/1310, MB1260/MB1360, and MB1261/MB1361, this distance is 25-cm.

Please see Close Range Operation

Notes:

Objects from 0-mm to 1-mm may not be detected.

For the MB1200/MB1300, MB1210/1310,

MB1260/MB1360, and MB1261/MB1361, this

distance is 25-cm.

Please see Close Range Operation.

MB1200 through MB1240 and MB1300 through

MB1340.

MB1260, MB1261, MB1360, MB1361.

See page 2, Pin 6 Vcc Operation.

Please reference page 4 for minimum

operating voltage verses temperature

information.

Please reference page 16 for part number key.

Features

• High acoustic power output

• Real-time auto sensitivity

adjustments and noise rejection for

every ranging cycle

• Calibrated beam angle

• Continuously variable gain

• Object detection as close as 1-mm

from the sensor

• 3.3V to 5.5V supply with very low

average current draw

6,7

• Readings can occur up to every

100mS, (10-Hz rate)

• Free run operation can

continually measure and output range

information

• Triggered operation provides the

range reading as desired

• Pulse Width (MB1200 series)

• Real-time analog envelope (MB1300

series)

• All interfaces are active

simultaneously

• Sensor operates at 42KHz

• Serial, 0 to Vcc, 9600Baud, 81N

• Analog, (Vcc/1024) / cm

• Analog, (Vcc/1024) / 2cm

Benefits

• Acoustic and electrical noise

resistance

• Reliable and stable range data

• Low cost

• Quality controlled beam

characteristics

• Very low power range, excellent for

multiple sensor or battery based

systems

• Ranging can be triggered externally

or internally

• Sensor reports the range reading

directly, frees up user processor

• Fast measurement cycle

• User can choose any of the sensor

outputs

• Easy mounting

• No power up calibration required

• Perfect for objects that may be

directly in front of the sensor during

power up

Applications and Uses

• Bin level measurement

• Proximity zone detection

• People detection

• Robot ranging sensor

• Autonomous navigation

• Environments with acoustic and

electrical noise

• Multi-sensor arrays

• Distance measuring

• Long range object detection

• Users who prefer to process the

analog voltage envelope (MB1300

series)

• -40°C to +65°C operation (+85°C

limited operation) (40°C to 0°C

recommended operation in

environments that are non-frosting,

non-condensation, and indoor only)

Close Range Operation

Applications requiring 100% reading-to-reading reliability should not use MaxSonar sensors at a distance closer than

20cm. Although most users find MaxSonar sensors to work reliably from 0 to 20cm

2,3

for detecting objects in many

applications, MaxBotix

Inc. does not guarantee operational reliability for objects closer than the minimum reported

distance. Because of ultrasonic physics, these sensors are unable to achieve 100% reliability at close distances.

______________________________________________________________________________________________________________________________________

Warning: Personal Safety Applications

We do not recommend or endorse this product be used as a component in any personal safety applications. This product

is not designed, intended or authorized for such use. These sensors and controls do not include the self-checking

redundant circuitry needed for such use. Such unauthorized use may create a failure of the MaxBotix

Inc. product which

may result in personal injury or death. MaxBotix

Inc. will not be held liable for unauthorized use of this component.

Summary of content (18 pages)

PAGE 1
XL-MaxSonar®- EZ™ Series XL-MaxSonar® - EZ/AE™ Series High Performance Sonar Range Finder MB1200, MB1210, MB1220, MB1230, MB1240, MB1260, MB1261 MB1300, MB1310, MB1320, MB1330, MB1340, MB1360, MB13618 The XL-MaxSonar-EZ series has high power output along with real-time auto sensitivity adjustments for changing conditions (temperature, voltage and acoustic or electrical noise) that ensure you receive the most reliable (in air) ranging data for every reading taken.
PAGE 2
XL-MaxSonar® - EZ/AE™ Series About Ultrasonic Sensors Our ultrasonic sensors are in air, non-contact object detection and ranging sensors that detect objects within an area. These sensors are not affected by the color or other visual characteristics of the detected object. Ultrasonic sensors use high frequency sound to detect and localize objects in a variety of environments. Ultrasonic sensors measure the time of flight for sound that has been transmitted to and reflected back from nearby objects.
PAGE 3
XL-MaxSonar® - EZ/AE™ Series Sensor Minimum Distance The sensor minimum reported distance is 20cm1 (7.87 inches). However, the XL-MaxSonar-EZ will range and report targets to the front sensor face. Large targets closer than 20cm1 will typically range as 20cm1. 1 For the MB1200/MB1300, MB1210/1310, MB1260/MB1360, and MB1261/MB1361, this distance is 25-cm.
PAGE 4
XL-MaxSonar® - EZ/AE™ Series Voltage vs Temperature The graph below shows minimum operating voltage of the sensor verses temperature. MaxBotix Inc., products are engineered and assembled in the USA. Copyright 2005 - 2021 MaxBotix Incorporated Patent 7,679,996 Page 4 Web: www.maxbotix.
PAGE 5
XL-MaxSonar® - EZ/AE™ Series Real-time Noise Rejection While the XL-MaxSonar® is designed to operate in the presence of noise, best operation is obtained when noise strength is low and desired signal strength is high. Hence, the user is encouraged to mount the sensor in such a way that minimizes outside acoustic noise pickup. In addition, keep the DC power to the sensor free of noise.
PAGE 6
XL-MaxSonar® - EZ/AE™ Series Sensor Timing Diagrams Power Up Timing Sensor Free-Run Timing Real-Time Operation Timing Description 175mS after power-up, the XL-MaxSonar is ready to begin ranging. If Pin-4 is left open or held high (20uS or greater), the sensor will take a range reading. The XL-MaxSonar checks the Pin-4 at the end of every cycle. Range data can be acquired once every 99mS. Each 99mS period starts by Pin-4 being high or open, after which the XL-MaxSonar calibrates and calculates for 20.
PAGE 7
XL-MaxSonar® - EZ/AE™ Series Using Multiple Sensors in a single system When using multiple ultrasonic sensors in a single system, there can be interference (cross-talk) from the other sensors. MaxBotix Inc., has engineered a solution to this problem for the XL-MaxSonar-EZ sensors. The solution is referred to as chaining. We have 3 methods of chaining that work well to avoid the issue of cross-talk. The first method is AN Output Commanded Loop.
PAGE 8
XL-MaxSonar® - EZ/AE™ Series Independent Sensor Operation The XL-MaxSonar-EZ sensors have the capability to operate independently when the user desires. When using the XL-MaxSonar-EZ sensors in single or independent sensor operation, it is easiest to allow the sensor to free-run. Free-run is the default mode of operation for all of the MaxBotix Inc., sensors. The XL-MaxSonar-EZ sensors have three separate outputs that update the range data simultaneously: Analog Voltage, Pulse Width, and RS232 Serial.
PAGE 9
XL-MaxSonar® - EZ/AE™ Series _______________________________________________________________________________________________________________________________________ Beam Characteristics Background Information Regarding our Beam Patterns Each XL-MaxSonar-EZ sensor has a calibrated beam pattern. Each sensor is matched to provide the People Sensing: approximate detection pattern shown in this datasheet.
PAGE 10
MB1200/MB1300: XL-MaxSonar-EZ/AE0 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZ/AE0 is the highest sensitivity and widest beam sensor of the XL-MaxSonar-EZ/AE sensor series. The wide beam makes this sensor ideal for a variety of applications including people detection, autonomous navigation, and wide beam applications. Note: All sensors sold after Oct 01, 2013 have a minimum reported distance of 25cm. All sensors sold before this date have a 20cm minimum reported distance.
PAGE 11
MB1210/MB1310: XL-MaxSonar-EZ/AE1 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZ/AE1 has slightly less sensitivity and narrower beam than the MB1200/MB1300 sensors. This makes the MB1210/MB1310 an ideal sensor for applications in which the MB1200/MB1300 are too sensitive. Note: All sensors sold after Oct 01, 2013 have a minimum reported distance of 25cm. All sensors sold before this date have a 20cm minimum reported distance.
PAGE 12
MB1220/MB1320: XL-MaxSonar-EZ/AE2 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZ/AE2 is the recommended sensor for users unsure of which XL-MaxSonar-EZ/AE sensor to use. This sensor balances sensitivity and detection to targets of different sizes. This sensor is a good comprise between sensitivity and side object rejection.
PAGE 13
MB1230/MB1330: XL-MaxSonar-EZ/AE3 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZ/AE3 is a narrow beam, and is slightly more sensitive then the MB1240/MB1340.
PAGE 14
MB1240/MB1340: XL-MaxSonar-EZ/AE4 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZ/AE4 is the least sensitive and narrowest beam pattern in the XL-MaxSonar-EZ/AE sensor series. This makes the senor great for applications in which there is a large amount of acoustic. The MB1240/MB1340 sensor is also recommended in applications where only large target detection is required.
PAGE 15
MB1260/MB1360: XL-MaxSonar-EZ/AEL0 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZL/AEL0 has the same gain and sensitive as the MB1200/MB1300. This sensor features a longer range of 1068cm to large targets. This sensor is recommended for long range measurement to large targets. Note: Firmware rev 1.6b and newer have a 25cm minimum reported distance. This applies to all sensors sold after February 20, 2013. All sensors sold before this date have a 20cm minimum reported distance.
PAGE 16
MB1261/MB1361: XL-MaxSonar-EZL/AEL1 XL-MaxSonar® - EZ/AE™ Series The XL-MaxSonar-EZL/AEL1 is the long range version of the MB1210/MB1310 ultrasonic sensor. This sensor features a longer maximum range of 1068cm to large targets. This sensor is recommended for applications in which the MB1210/ MB1310 do not have a long enough detection distance.
PAGE 17
XL-MaxSonar® - EZ/AE™ Series Part Numbers All part numbers are a combination of a six-character base followed by a dash and a three-digit product code. Please review the following table for more information on the three-digit product code.
PAGE 18
XL-MaxSonar® - EZ/AE™ Series After reviewing this datasheet, do you have any more questions? We offer Technical Support on all of our products even if you purchased them through one of our many vendors worldwide.