Datasheet
Table Of Contents
- 1 Hardware Description
- 1.1 Hardware Overview
- 1.2 Analog Front End (AFE)
- 1.3 Digital Computation Engine (CE)
- 1.4 80515 MPU Core
- 1.4.1 Memory Organization and Addressing
- 1.4.2 Special Function Registers (SFRs)
- 1.4.3 Generic 80515 Special Function Registers
- 1.4.4 Special Function Registers (SFRs) Specific to the 71M6531D/F and 71M6532D/F
- 1.4.5 Instruction Set
- 1.4.6 UARTs
- 1.4.7 Timers and Counters
- 1.4.8 WD Timer (Software Watchdog Timer)
- 1.4.9 Interrupts
- 1.5 On-Chip Resources
- 1.5.1 Oscillator
- 1.5.2 Internal Clocks
- 1.5.3 Real-Time Clock (RTC)
- 1.5.4 Temperature Sensor
- 1.5.5 Physical Memory
- 1.5.6 Optical Interface
- 1.5.7 Digital I/O – 71M6531D/F
- 1.5.8 Digital I/O – 71M6532D/F
- 1.5.9 Digital IO – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.10 LCD Drivers – 71M6531D/F
- 1.5.11 LCD Drivers – 71M6532D/F
- 1.5.12 LCD Drivers – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.13 Battery Monitor
- 1.5.14 EEPROM Interface
- 1.5.15 SPI Slave Port
- 1.5.16 Hardware Watchdog Timer
- 1.5.17 Test Ports (TMUXOUT pin)
- 2 Functional Description
- 3 Application Information
- 3.1 Connection of Sensors
- 3.2 Connecting 5-V Devices
- 3.3 Temperature Measurement
- 3.4 Temperature Compensation
- 3.5 Connecting LCDs
- 3.6 Connecting I2C EEPROMs
- 3.7 Connecting Three-Wire EEPROMs
- 3.8 UART0 (TX/RX)
- 3.9 Optical Interface (UART1)
- 3.10 Connecting the V1 Pin
- 3.11 Connecting the Reset Pin
- 3.12 Connecting the Emulator Port Pins
- 3.13 Connecting a Battery
- 3.14 Flash Programming
- 3.15 MPU Firmware
- 3.16 Crystal Oscillator
- 3.17 Meter Calibration
- 4 Firmware Interface
- 4.1 I/O RAM and SFR Map – Functional Order
- 4.2 I/O RAM Description – Alphabetical Order
- 4.3 CE Interface Description
- 5 Electrical Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 Recommended External Components
- 5.3 Recommended Operating Conditions
- 5.4 Performance Specifications
- 5.4.1 Input Logic Levels
- 5.4.2 Output Logic Levels
- 5.4.3 Power-Fault Comparator
- 5.4.4 Battery Monitor
- 5.4.5 Supply Current
- 5.4.6 V3P3D Switch
- 5.4.7 2.5 V Voltage Regulator
- 5.4.8 Low-Power Voltage Regulator
- 5.4.9 Crystal Oscillator
- 5.4.10 LCD DAC
- 5.4.11 LCD Drivers
- 5.4.12 Optical Interface
- 5.4.13 Temperature Sensor
- 5.4.14 VREF
- 5.4.15 ADC Converter, V3P3A Referenced
- 5.5 Timing Specifications
- 5.6 Typical Performance Data
- 5.7 71M6531D/F Package
- 5.8 71M6532D/F Package
- 5.9 Pin Descriptions
- 6 Ordering Information
- 7 Related Information
- 8 Contact Information
- Appendix A: Acronyms
- Appendix B: Revision History
![](/manual/maxim-integrated/71m6531f-im-f/datasheet-english/images/img-100.png)
Data Sheet 71M6531D/F-71M6532D/F FDS 6531/6532 005
100 Rev 2
5.4 Performance Specifications
5.4.1 Input Logic Levels
Table 70: Input Logic Levels
Parameter
Condition
Min
Typ
Max
Unit
Digital high-level input voltage
a
, V
IH
2
V
Digital low-level input voltage
a
, V
IL
0.8
V
Input pull-up current, I
IL
E_RXTX,
E_RST, CKTEST
Other digital inputs
VIN=0 V, ICE_E=1
10
10
-1
0
100
100
1
µA
µA
µA
Input pull down current, I
IH
ICE_E
RESET
PB
Other digital inputs
VIN = V3P3D
10
10
-1
-1
0
0
100
100
1
1
µA
µA
µA
µA
a
In battery powered modes, digital inputs should be below 0.3 V or above 2.5 V to minimize battery current.
5.4.2 Output Logic Levels
Table 71: Output Logic Levels
Parameter
Condition
Min
Typ
Max
Unit
Digital high-level output voltage V
OH
I
LOAD
= 1 mA
V3P3D–0.4
V
I
LOAD
= 15 mA
V3P3D-0.6
V
Digital low-level output voltage V
OL
I
LOAD
= 1 mA
0
0.4
V
I
LOAD
= 15 mA
0.8
V
OPT_TX VOH (V3P3D-OPT_TX)
ISOURCE=1 mA
0.4
V
OPT_TX VOL
ISINK=20 mA
0.7
V
5.4.3 Power-Fault Comparator
Table 72: Power-Fault Comparator Performance Specifications
Parameter
Condition
Min
Typ
Max
Unit
Offset Voltage: V1-VBIAS
-20
+15
mV
Hysteresis Current: V1
Vin = VBIAS – 100 mV
0.8
1.2
μA
Response Time: V1
+100 mV overdrive
Voltage at V1 rising
Voltage at V1 falling
10
8
37
100
100
µs
μs
WDT Disable Threshold: V1-V3P3A
-400
-10
mV
5.4.4 Battery Monitor
Table 73: Battery Monitor Performance Specifications (BME= 1)
Parameter
Condition
Min
Typ
Max
Unit
Load Resistor
27
45
63
kΩ
LSB Value
[M40MHZ, M26MHZ]
= [00], [10], or [11]
FIR_LEN[1:0]=0 (L=138)
FIR_LEN[1:0]=1 (L=288)
FIR_LEN[1:0]=2 (L=384)
(-10%)
-48.7
-5.35
-2.26
(+10%)
μV
μV
μV
[M40MHZ, M26MHZ]
= [01]
FIR_LEN[1:0]=0 (L=186)
FIR_LEN[1:0]=1 (L=384)
FIR_LEN[1:0]=2 (L=588)
(-10%)
-19.8
-2.26
-0.63
(+10%)
μV
μV
μV
Offset Error
-200
0
+100
mV