Datasheet
Table Of Contents
- 1 Hardware Description
- 1.1 Hardware Overview
- 1.2 Analog Front End (AFE)
- 1.3 Digital Computation Engine (CE)
- 1.4 80515 MPU Core
- 1.4.1 Memory Organization and Addressing
- 1.4.2 Special Function Registers (SFRs)
- 1.4.3 Generic 80515 Special Function Registers
- 1.4.4 Special Function Registers (SFRs) Specific to the 71M6531D/F and 71M6532D/F
- 1.4.5 Instruction Set
- 1.4.6 UARTs
- 1.4.7 Timers and Counters
- 1.4.8 WD Timer (Software Watchdog Timer)
- 1.4.9 Interrupts
- 1.5 On-Chip Resources
- 1.5.1 Oscillator
- 1.5.2 Internal Clocks
- 1.5.3 Real-Time Clock (RTC)
- 1.5.4 Temperature Sensor
- 1.5.5 Physical Memory
- 1.5.6 Optical Interface
- 1.5.7 Digital I/O – 71M6531D/F
- 1.5.8 Digital I/O – 71M6532D/F
- 1.5.9 Digital IO – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.10 LCD Drivers – 71M6531D/F
- 1.5.11 LCD Drivers – 71M6532D/F
- 1.5.12 LCD Drivers – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.13 Battery Monitor
- 1.5.14 EEPROM Interface
- 1.5.15 SPI Slave Port
- 1.5.16 Hardware Watchdog Timer
- 1.5.17 Test Ports (TMUXOUT pin)
- 2 Functional Description
- 3 Application Information
- 3.1 Connection of Sensors
- 3.2 Connecting 5-V Devices
- 3.3 Temperature Measurement
- 3.4 Temperature Compensation
- 3.5 Connecting LCDs
- 3.6 Connecting I2C EEPROMs
- 3.7 Connecting Three-Wire EEPROMs
- 3.8 UART0 (TX/RX)
- 3.9 Optical Interface (UART1)
- 3.10 Connecting the V1 Pin
- 3.11 Connecting the Reset Pin
- 3.12 Connecting the Emulator Port Pins
- 3.13 Connecting a Battery
- 3.14 Flash Programming
- 3.15 MPU Firmware
- 3.16 Crystal Oscillator
- 3.17 Meter Calibration
- 4 Firmware Interface
- 4.1 I/O RAM and SFR Map – Functional Order
- 4.2 I/O RAM Description – Alphabetical Order
- 4.3 CE Interface Description
- 5 Electrical Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 Recommended External Components
- 5.3 Recommended Operating Conditions
- 5.4 Performance Specifications
- 5.4.1 Input Logic Levels
- 5.4.2 Output Logic Levels
- 5.4.3 Power-Fault Comparator
- 5.4.4 Battery Monitor
- 5.4.5 Supply Current
- 5.4.6 V3P3D Switch
- 5.4.7 2.5 V Voltage Regulator
- 5.4.8 Low-Power Voltage Regulator
- 5.4.9 Crystal Oscillator
- 5.4.10 LCD DAC
- 5.4.11 LCD Drivers
- 5.4.12 Optical Interface
- 5.4.13 Temperature Sensor
- 5.4.14 VREF
- 5.4.15 ADC Converter, V3P3A Referenced
- 5.5 Timing Specifications
- 5.6 Typical Performance Data
- 5.7 71M6531D/F Package
- 5.8 71M6532D/F Package
- 5.9 Pin Descriptions
- 6 Ordering Information
- 7 Related Information
- 8 Contact Information
- Appendix A: Acronyms
- Appendix B: Revision History
FDS 6531/6532 005 Data Sheet 71M6531D/F-71M6532D/F
Rev 2 83
Name
Location
Reset
Wake
Dir
Description
LCD_SEG33[3:0]
…
LCD_SEG35[3:0]
2051[3:0]
…
2053[3:0]
0
…
0
L
…
L
R/W
…
R/W
LCD_SEG37[3:0]
2055[3:0]
0
L
R/W
LCD_SEG39[3:0]
…
LCD_SEG41[3:0]
2057[3:0]
…
2059[3:0]
0
…
0
L
…
L
R/W
…
R/W
LCD_SEG48[7:4]
…
LCD_SEG49[7:4]
2036[7:4]
…
2037[7:4]
0
…
0
L
…
L
R/W
…
R/W
LCD_SEG63[7:4]
…
LCD_SEG66[7:4]
2045[7:4]
…
2048[7:4]
0
…
0
L
…
L
R/W
…
R/W
LCD_SEG71[7:4]
…
LCD_SEG73[7:4]
204D[7:4]
…
204F[7:4]
0
…
0
L
…
L
R/W
…
R/W
LCD_Y
2021[6] 0 L R/W
LCD Blink Frequency (ignored if blink is disabled or if the segment is off).
0 = 1 Hz (500 ms ON, 500 ms OFF)
1 = 0.5 Hz (1 s ON, 1 s OFF)
M26MHZ
M40MHZ
2005[4]
2005[0]
0
0
0
0
R/W
R/W
M26MHZ and M40MHZ set the master clock (MCK) frequency. These bits are reset on
chip reset and may only be set. Attempts to write zeroes to M40MHZ and M26MHZ.are
ignored.
MPU_DIV[2:0]
2004[2:0] 0 0 R/W
The MPU clock divider (from MCK). These bits may be programmed by MPU without
risk of losing control.
MPU_DIV[2:0]
Resulting Clock Frequency
000
MCK/2
2
001
MCK/2
3
010
MCK/2
4
011
MCK/2
5
100
MCK/2
6
101
MCK/2
7
110
MCK/2
8
111
MCK/2
8