Datasheet
Table Of Contents
- 1 Hardware Description
- 1.1 Hardware Overview
- 1.2 Analog Front End (AFE)
- 1.3 Digital Computation Engine (CE)
- 1.4 80515 MPU Core
- 1.4.1 Memory Organization and Addressing
- 1.4.2 Special Function Registers (SFRs)
- 1.4.3 Generic 80515 Special Function Registers
- 1.4.4 Special Function Registers (SFRs) Specific to the 71M6531D/F and 71M6532D/F
- 1.4.5 Instruction Set
- 1.4.6 UARTs
- 1.4.7 Timers and Counters
- 1.4.8 WD Timer (Software Watchdog Timer)
- 1.4.9 Interrupts
- 1.5 On-Chip Resources
- 1.5.1 Oscillator
- 1.5.2 Internal Clocks
- 1.5.3 Real-Time Clock (RTC)
- 1.5.4 Temperature Sensor
- 1.5.5 Physical Memory
- 1.5.6 Optical Interface
- 1.5.7 Digital I/O – 71M6531D/F
- 1.5.8 Digital I/O – 71M6532D/F
- 1.5.9 Digital IO – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.10 LCD Drivers – 71M6531D/F
- 1.5.11 LCD Drivers – 71M6532D/F
- 1.5.12 LCD Drivers – Common Characteristics for 71M6531D/F and 71M6532D/F
- 1.5.13 Battery Monitor
- 1.5.14 EEPROM Interface
- 1.5.15 SPI Slave Port
- 1.5.16 Hardware Watchdog Timer
- 1.5.17 Test Ports (TMUXOUT pin)
- 2 Functional Description
- 3 Application Information
- 3.1 Connection of Sensors
- 3.2 Connecting 5-V Devices
- 3.3 Temperature Measurement
- 3.4 Temperature Compensation
- 3.5 Connecting LCDs
- 3.6 Connecting I2C EEPROMs
- 3.7 Connecting Three-Wire EEPROMs
- 3.8 UART0 (TX/RX)
- 3.9 Optical Interface (UART1)
- 3.10 Connecting the V1 Pin
- 3.11 Connecting the Reset Pin
- 3.12 Connecting the Emulator Port Pins
- 3.13 Connecting a Battery
- 3.14 Flash Programming
- 3.15 MPU Firmware
- 3.16 Crystal Oscillator
- 3.17 Meter Calibration
- 4 Firmware Interface
- 4.1 I/O RAM and SFR Map – Functional Order
- 4.2 I/O RAM Description – Alphabetical Order
- 4.3 CE Interface Description
- 5 Electrical Specifications
- 5.1 Absolute Maximum Ratings
- 5.2 Recommended External Components
- 5.3 Recommended Operating Conditions
- 5.4 Performance Specifications
- 5.4.1 Input Logic Levels
- 5.4.2 Output Logic Levels
- 5.4.3 Power-Fault Comparator
- 5.4.4 Battery Monitor
- 5.4.5 Supply Current
- 5.4.6 V3P3D Switch
- 5.4.7 2.5 V Voltage Regulator
- 5.4.8 Low-Power Voltage Regulator
- 5.4.9 Crystal Oscillator
- 5.4.10 LCD DAC
- 5.4.11 LCD Drivers
- 5.4.12 Optical Interface
- 5.4.13 Temperature Sensor
- 5.4.14 VREF
- 5.4.15 ADC Converter, V3P3A Referenced
- 5.5 Timing Specifications
- 5.6 Typical Performance Data
- 5.7 71M6531D/F Package
- 5.8 71M6532D/F Package
- 5.9 Pin Descriptions
- 6 Ordering Information
- 7 Related Information
- 8 Contact Information
- Appendix A: Acronyms
- Appendix B: Revision History
Data Sheet 71M6531D/F-71M6532D/F FDS 6531/6532 005
98 Rev 2
5 Electrical Specifications
5.1 Absolute Maximum Ratings
Table 67 shows the absolute maximum ranges for the device. Stresses beyond Absolute Maximum Ratings
may cause permanent damage to the device. These are stress ratings only and functional operation at
these or any other conditions beyond those indicated under recommended operating conditions (Section
5.3) is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability. All voltages are with respect to GNDA.
Table 67: Absolute Maximum Ratings
Voltage and Current
Supplies and Ground Pins
V3P3SYS, V3P3A
−
0.5 V to 4.6 V
VBAT
-0.5 V to 4.6 V
GNDD
-0.5 V to +0.5 V
Analog Output Pins
V3P3D
-10 mA to 10 mA,
-0.5 V to 4.6 V
VREF
-10 mA to +10 mA,
-0.5 V to V3P3A+0.5 V
V2P5
-10 mA to +10 mA,
-0.5 V to 3.0 V
Analog Input Pins
IA, VA, IB, VB, V1
-10 mA to +10 mA
-0.5 V to V3P3A+0.5 V
XIN, XOUT
-10 mA to +10 mA
-0.5 V to 3.0 V
All Other Pins
Configured as SEG or COM drivers
-1 mA to +1 mA,
-0.5 to V3P3D+0.5
Configured as Digital Inputs
-10 mA to +10 mA,
-0.5 to 6 V
Configured as Digital Outputs
-15 mA to +15 mA,
-0.5 V to V3P3D+0.5 V
All other pins
−
0.5 V to V3P3D+0.5 V
Temperature and ESD Stress
Operating junction temperature (peak, 100ms)
140 °C
Operating junction temperature (continuous)
125 °C
Storage temperature
−
45 °C to +165 °C
Solder temperature – 10 second duration
250 °C
ESD stress on all pins
4 kV