73M1866B/73M1966B GUI User Guide March 23, 2009 Rev. 1.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 © 2009 Teridian Semiconductor Corporation. All rights reserved. Teridian Semiconductor Corporation is a registered trademark of Teridian Semiconductor Corporation. Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective owners.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide Table of Contents 1 Introduction ................................................................................................................................... 5 2 Getting Started............................................................................................................................... 6 2.1 GUI Installation ........................................................................................................................ 6 2.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 Figure Figure 1: Register Access Screen – R00-R09 Tab ................................................................................... 8 Table Table 1: GUI Controls .............................................................................................................................. 9 4 Rev. 1.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide 1 Introduction The 73M1866B/73M1966B Graphical User Interface (GUI) provides control of the 73M1866B and 73M1966B registers. The GUI is used to configure the 73M1866B and 73M1966B demo boards and to read the status conditions of these boards. This document applies to GUI software version 1.3. The GUI can be use with either the Demo Board or the Keychain Board. The GUI cannot be used if the SPI is connected to a host device.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 2 Getting Started This section describes how to install, start and use the GUI software. 2.1 GUI Installation Load the GUI software from the CD onto the PC that will be used to control the configuration of the 73M1x66B Demo Board. If the GUI software does not run automatically when the CD is installed, select Start Run and browse the CD drive for Teridian_73M1966_1_3_SETUP.EXE. Select OK. The following window appears. Select Run.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide This window shows the default destination for the GUI software Select Next. The following window appears. The user can change the destination folder from the default. Change the destination folder or select Next to accept the default folder. The GUI software loads into the specified folder and the following window appears. The setup is complete. Click Finish. The software is ready for use. Rev. 1.
73M1866B/73M1966B GUI User Guide 2.2 UG_1x66B_002 Using the GUI The 73M1866B or 73M1966B Demo Board must be set up before using the GUI. See the 73M1866B/73M1966B Demo Board User Manual for setup procedures. To start the GUI using Windows XP, select Start All Programs Teridian Teridian 73M1966B. The Register Access screen appears (see Figure 1). The screen is divided into a top half and a bottom half. The first row of the top half consists of five tabs: R00-R09, R0A-R12, R13-R1B, R1C-R25 and FPGA.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide The bottom half of the Register Access screen shows the status of the entire 73M1x66B register set (in hex) and provides information and parameter controls. Table 1 describes these controls. Table 1: GUI Controls Click Write Red to write all red values in the bottom half of the screen. Values become red when changed by checking or un-checking boxes in the top half of the screen. Click Write all to write all values (both read and black).
73M1866B/73M1966B GUI User Guide UG_1x66B_002 Sets the registers to a user-defined configuration contained in a specified script file. This is used to quickly put the registers into a configuration and the 73M1x66 into operational mode without having to individually set the register bits. If you have a configuration that you will use again later, the configuration can be saved as a script. See Log All Register Accesses to File. Used to keep a record of all register accesses performed by the user.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide 2.2.1 Controls for Registers R00 to R09 The GUI represents 73M1x66B registers in the form Rhh, where hh is the hexadecimal address. The 73M1866B/73M1966B Data Sheet represents these same registers in the form 0xhh. For detailed descriptions of 73M1x66B registers, see the 73M1866B/73M1966B Data Sheet. The tables below list the section numbers in the 73M1866B/73M1966B Data Sheet where additional information can be found about each bit.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 2.2.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide 2.2.3 Controls for Registers R13 to R1C Register Bit Name R13[7:6] R13[5] R13[4] R13[3] R13[2] R13[1] R13[0] R14[7] R14[6:5] DCIVn ILM ACCEN PLDM OVDTH IDISPD SEL16K TXBST DAAn R14[3] RXBST R14[2] RLPNH R14[1:0] R15[7] R15[6] R15[5] R15[4] R15[3] R15[2] R15[1] R15[0] R16[7] R16[6] R16[5] R16[4] R16[3:0] R17[5] R18[7:4] R19[7] RXGn ENOLD DISNTR CHPSEN CIDM THEN ENUVD ENOVD ENOID TXEN RXEN RLPNEN ATEN ACZn RXOCEN TESTn POLL Rev. 1.
73M1866B/73M1966B GUI User Guide Register Bit Name R19[6] R19[4] R19[3:0] MATCH IDL2 INDXn R1A[7:0] R1B[7:1] RNGn LVn 14 UG_1x66B_002 Summary Description Polling Match Ring Detect Functions Index Address of the register to be manually polled with the results placed in POLVAL. Result of Auxiliary A/D measuring the attenuated ring voltage. Line Voltage Reading Data Sheet Section 6.1 7.3 6.1 11.12 11.12 Rev. 1.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide 2.2.4 Controls for Registers R1D to R23 Registers Description R1C[7:1] R1D[7:4] R1E[7] R1E[6] R1E[5] R1E[4] R1E[3] R1E[2] R1F[7:0] LCn REVLSDn ILMON UVDET OVDET OIDET OLDET SLLS POLLVALn R20[7] R20[6:0] R21[7] R21[6:0] R22[7] R22[6] R22[5:3] R22[2:0] R23[7] R23[6] TPOL TTSn RPOL RTSn SR ADJ RCSn TCSn PCMEN MASTER R23[5:2] R23[1] R23[0] PCODEn LIN LAW R24[0] LB Rev. 1.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 3 Scripts If you have a configuration that will be used again later, the configuration can be saved by simple saving the current configuration by selecting “Save As Script” from the “File” drop-down menu. This will save ALL the register status information. Once the file has been saved, it can be edited so that only the registers you are interested in changing are contained in the file.
UG_1x66B_002 73M1866B/73M1966B GUI User Guide This is a listing of the “ring-rev-set-up.
73M1866B/73M1966B GUI User Guide UG_1x66B_002 ' Disable off hook functions except RXEN for CID W,1,0,0,16,40 ' Set DX polarity, timeslot 0 of WG W,1,0,0,20,9F ' Set DR polarity, timeslot 0 of WG W,1,0,0,21,1F ' Set clock slot for timeslot 0 of WG W,1,0,0,22,3F 4 Related Documentation The following 73M1x66B documents are available from Teridian Semiconductor Corporation: 73M1866B/73M1966B Data Sheet 73M1966B Evaluation Kit User Manual 73M1866/73M1966B Demo Board User Manual 73M1866/73M1966B Keychain Demo
