Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsLinear ICsDS1878T+

DS1878

SFP+ Controller with Digital LDD Interface

______________________________________________________________________________________ 33

Table 05h is empty by default. It can be configured to

contain the alarm- and warning-enable bytes from Table

01h, Registers F8h–FFh with the MASK bit enabled

(Table 02h, Register 89h). In this case Table 01h is

empty.

Table 06h contains a temperature-indexed LUT that

allows the APC set point to change as a function of

temperature to compensate for TE. The APC LUT has

36 entries that determine the APC setting in 4°C win-

dows between -40°C and +100°C.

Table 07h contains a temperature-indexed LUT for con-

trol of DAC1. The LUT has 36 entries that determine the

DAC setting in 4°C windows between -40°C and +100°C.

Table 08h contains a temperature-indexed LUT for con-

trol of DAC2. The LUT has 36 entries that determine the

DAC setting in 4°C windows between -40°C and +100°C.

Auxiliary Memory (device A0h) contains 256 bytes of

EE memory accessible from address 00h–FFh. It is

selected with the device address of A0h.

See the

section for more com-

plete details of each byte’s function, as well as for

read/write permissions for each byte.

Shadowed EEPROM

Many NV memory locations (listed within the

Descriptions

section) are actually shadowed EEPROM

that are controlled by the SEEB bit in Table 02h,

The device incorporates shadowed-EEPROM memory

locations for key memory addresses that can be writ-

ten many times. By default the shadowed-EEPROM bit,

SEEB, is not set and these locations act as ordinary

EEPROM. By setting SEEB, these locations function

like SRAM cells, which allow an infinite number of write

cycles without concern of wearing out the EEPROM.

Setting SEEB also eliminates the requirement for the

EEPROM write time, t

. Because changes made with

SEEB enabled do not affect the EEPROM, these

changes are not retained through power cycles. The

power-on value is the last value written with SEEB dis-

abled. This function can be used to limit the number of

EEPROM writes during calibration or to change the

monitor thresholds periodically during normal opera-

tion helping to reduce the number of times EEPROM is

written.

EEPROM

(256 BYTES)

FFh

C ADDRESS A0h I

C ADDRESS A2h (DEFAULT)

AUXILIARY DEVICE

MAIN DEVICE

00h

ALARM-

ENABLE ROW

(8 BYTES)

PASSWORD ENTRY

(PWE) (4 BYTES)

TABLE-SELECT

BYTE

FFh

80h

F8h

TABLE 01h

EEPROM

(120 BYTES)

F7h

7Fh

00h

LOWER

MEMORY

3W CONFIG

FFh

80h

E8h

TABLE 02h

NONLOOKUP

TABLE CONTROL

AND

CONFIGURATION

REGISTERS

E7h

80h

TABLE 04h

MOD LUT

(72 BYTES)

C7h

F8h

TABLE 05h

ALARM-ENABLE ROW

(8 BYTES)

FFh

80h

TABLE 06h

APC LUT

(36 BYTES)

A3h

80h

TABLE 07h

DAC1 LUT

(36 BYTES)

A3h

80h

TABLE 08h

DAC2 LUT

(36 BYTES)

A3h

NOTE 1: IF ASEL = 0, THEN THE MAIN DEVICE I

C SLAVE ADDRESS IS A2h.

IF ASEL = 1, THEN THE MAIN DEVICE I

C SLAVE ADDRESS IS DETERMINED BY THE VALUE IN

TABLE 02h, REGISTER 8Ch.

NOTE 2: TABLE 00h DOES NOT EXIST.

NOTE 3: ALARM-ENABLE ROW CAN BE CONFIGURED TO EXIST AT TABLE 01h OR TABLE 05h USING THE

MASK BIT IN TABLE 02h, REGISTER 89h.

Figure 22. Memory Map