Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsData collecting ICsData acquisition IC - AD converter (ADC) External , Internal QSOP 20

General Description

The MAX1227/MAX1229/MAX1231 are serial 12-bit ana-

log-to-digital converters (ADCs) with an internal reference

and an internal temperature sensor. These devices fea-

ture an on-chip FIFO, scan mode, internal clock mode,

internal averaging, and AutoShutdown™. The maximum

sampling rate is 300ksps using an external clock. The

MAX1231 has 16 input channels, the MAX1229 has 12

input channels, and the MAX1227 has 8 input channels.

All input channels are configurable for single-ended or

differential inputs in unipolar or bipolar mode. All three

devices operate from a +3V supply and contain a 10MHz

SPI™-/QSPI™-/MICROWIRE™-compatible serial port.

The MAX1231 is available in 28-pin 5mm x 5mm TQFN

with exposed pad and 24-pin QSOP packages. The

MAX1227/MAX1229 are only available in QSOP pack-

ages. All three devices are specified over the extended

-40°C to +85°C temperature range.

________________________Applications

System Supervision

Data-Acquisition Systems

Industrial Control Systems

Patient Monitoring

Data Logging

Instrumentation

Features

o Internal Temperature Sensor (±0.7°C Accuracy)

o 16-Entry First-In/First-Out (FIFO)

o Analog Multiplexer with True Differential

Track/Hold

16-, 12-, 8-Channel Single Ended

8-, 6-, 4-Channel True Differential

(Unipolar or Bipolar)

o Accuracy: ±1 LSB INL, ±1 LSB DNL, No Missing

Codes Overtemperature

o Scan Mode, Internal Averaging, and Internal Clock

o Low-Power Single +3V Operation

1mA at 300ksps

o Internal 2.5V Reference or External Differential

Reference

o 10MHz 3-Wire SPI-/QSPI-/MICROWIRE-Compatible

Interface

o Space-Saving 28-Pin 5mm x 5mm TQFN Package

MAX1227/MAX1229/MAX1231

12-Bit 300ksps ADCs with FIFO,

Temp Sensor, Internal Reference

________________________________________________________________

Maxim Integrated Products

AIN0

TOP VIEW

EOC

DOUT

DIN

SCLK

GND

REF+

MAX1227

QSOP

AIN1

AIN2

AIN5

AIN3

AIN4

REF-/AIN6

CNVST/AIN7

EOC

DOUT

DIN

CSAIN3

AIN2

AIN1

AIN0

SCLK

GND

REF+AIN7

AIN6

AIN5

AIN4

CNVST/AIN11

REF-/AIN10AIN9

AIN8

MAX1229

QSOP

Pin Configurations

19-2851; Rev 7; 4/12

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,

or visit Maxim’s website at www.maxim-ic.com.

EVALUATION KIT

AVAILABLE

Ordering Information

PART TEMP RANGE PIN-PACKAGE

MAX1227BCEE+ 0°C to +70°C 16 QSOP

MAX1227BEEE+ -40°C to +85°C 16 QSOP

MAX1229BCEP+ 0°C to +70°C 20 QSOP

MAX1229BEEP+ -40°C to +85°C 20 QSOP

Pin Configurations continued at end of data sheet.

Ordering Information continued at end of data sheet.

AutoShutdown is a trademark of Maxim Integrated Products, Inc.

SPI/QSPI are trademarks of Motorola, Inc.

MICROWIRE is a trademark of National Semiconductor Corp.

Denotes a lead(Pb)-free/RoHS-compliant package.

EP = Exposed pad (TQFN only). Connect to GND.

Summary of content (22 pages)

PAGE 1
9-2851; Rev 7; 4/12 KIT ATION EVALU E L B A IL AVA 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Features o Internal Temperature Sensor (±0.
PAGE 2
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference ABSOLUTE MAXIMUM RATINGS VDD to GND ..............................................................-0.3V to +6V CS, SCLK, DIN, EOC, DOUT to GND.........-0.3V to (VDD + 0.3V) AIN0–AIN13, REF-/AIN_, CNVST/AIN_, REF+ to GND.........................................-0.3V to (VDD + 0.3V) Maximum Current into Any Pin............................................50mA Continuous Power Dissipation (TA = +70°C) 16-Pin QSOP (derate 8.
PAGE 3
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference (VDD = +2.7V to +3.6V, fSAMPLE = 300kHz, fSCLK = 4.8MHz (50% duty cycle), VREF = 2.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS CONVERSION RATE Power-Up Time tPU Acquisition Time tACQ Conversion Time tCONV External Clock Frequency fSCLK External reference 0.8 Internal reference (Note 3) 65 Internally clocked 3.5 µs 0.
PAGE 4
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference ELECTRICAL CHARACTERISTICS (continued) (VDD = +2.7V to +3.6V, fSAMPLE = 300kHz, fSCLK = 4.8MHz (50% duty cycle), VREF = 2.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DIGITAL INPUTS (SCLK, DIN, CS, CNVST) (Note 8) Input Voltage Low VIL Input Voltage High VIH Input Hysteresis VDD x 0.3 VDD x 0.
PAGE 5
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference PARAMETER SYMBOL SCLK Clock Period tCP CONDITIONS MIN Externally clocked conversion 208 Data I/O 100 TYP MAX UNITS ns SCLK Duty Cycle tCH 60 % SCLK Fall to DOUT Transition tDOT CLOAD = 30pF 40 ns CS Rise to DOUT Disable tDOD CLOAD = 30pF 40 ns CS Fall to DOUT Enable tDOE CLOAD = 30pF 40 ns DIN to SCLK Rise Setup tDS 40 ns SCLK Rise to DIN Hold 40 tDH 0 CS Rise-to-SCLK Rise Setup Time tCSS1 40 ns CS Fal
PAGE 6
Typical Operating Characteristics (continued) (VDD = +3V, VREF = +2.5V, fSCLK = 4.8MHz, CLOAD = 30pF, TA = +25°C, unless otherwise noted.) SUPPLY CURRENT (µA) 600 80 60 40 500 400 700 0 1000 100 1 10 FREQUENCY (kHz) SUPPLY CURRENT vs. TEMPERATURE 625 MAX1227/29/31 toc07 0.4 fS = 300ksps SUPPLY CURRENT (µA) SHUTDOWN SUPPLY CURRENT (µA) 0.5 3.3 SUPPLY VOLTAGE (V) SAMPLING RATE (ksps) SHUTDOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE 0.3 0.2 620 615 610 0.1 0 605 2.7 3.0 3.3 3.
PAGE 7
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference INTERNAL REFERENCE VOLTAGE vs. TEMPERATURE 2.502 2.498 2.494 0.1 0 -0.1 -0.2 2.490 -15 10 35 60 85 3.0 3.3 -0.1 -40 3.6 -15 35 60 85 GAIN ERROR vs. TEMPERATURE 1.5 GAIN ERROR (LSB) 1.0 MAX1227/29/31 toc15 2.0 MAX1227/29/31 toc14 1.5 10 TEMPERATURE (°C) GAIN ERROR vs. SUPPLY VOLTAGE 1.0 0.5 0.5 0 2.7 3.0 -40 -15 10 35 60 SUPPLY VOLTAGE (V) TEMPERATURE (°C) TEMPERATURE SENSOR ERROR vs.
PAGE 8
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Pin Description PIN NAME FUNCTION MAX1231 TQFN-EP MAX1231 QSOP MAX1229 MAX1227 2–12, 26, 27, 28, 1–14 — — — — 1–10 — AIN0–9 Analog Inputs — — — 1–6 AIN0–5 Analog Inputs 13 15 — — REF-/AIN14 Negative Input for External Differential Reference/Analog Input 14. See Table 3 for details on programming the setup register.
PAGE 9
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference MAX1227/MAX1229/MAX1231 CS tCP tCH tCSS0 tCSH1 tCSH0 tCSS1 SCLK tDH tDS DIN tDOT tDOD tDOE DOUT Figure 1. Detailed Serial-Interface Timing Diagram CS DIN SCLK SERIAL INTERFACE OSCILLATOR CONTROL DOUT EOC CNVST AIN1 AIN2 T/H AIN15 12-BIT SAR ADC FIFO AND ACCUMULATOR TEMP SENSE REFREF+ INTERNAL REFERENCE MAX1227 MAX1229 MAX1231 Figure 2.
PAGE 10
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Converter Operation The MAX1227/MAX1229/MAX1231 ADCs use a fully differential, successive-approximation register (SAR) conversion technique and an on-chip T/H block to convert temperature and voltage signals into a 12-bit digital result. Both single-ended and differential configurations are supported, with a unipolar signal range for singleended mode and bipolar or unipolar ranges for differential mode.
PAGE 11
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference CIN+ DAC COMPARATOR + HOLD GND (SINGLE ENDED); AIN1, AIN3, AIN5…AIN15 (DIFFERENTIAL) CIN- HOLD HOLD VDD/2 Figure 3. Equivalent Input Circuit Unipolar/Bipolar Address the unipolar and bipolar registers through the setup register (bits 1 and 0). Program a pair of analog channels for differential operation by writing a 1 to the appropriate bit of the bipolar or unipolar register.
PAGE 12
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Applications Information Register Descriptions The MAX1227/MAX1229/MAX1231 communicate between the internal registers and the external circuitry through the SPI-/QSPI-compatible serial interface. Table 1 details the registers and the bit names. Tables 2–7 show the various functions within the conversion register, setup register, averaging register, reset register, unipolar register, and bipolar register.
PAGE 13
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference BIT NAME — BIT FUNCTION 7 (MSB) Set to 1 to select conversion register. CHSEL3 6 Analog input channel select. CHSEL2 5 Analog input channel select. CHSEL1 4 Analog input channel select. CHSEL0 3 Analog input channel select. SCAN1 2 Scan mode select. SCAN0 1 Scan mode select. TEMP Set to 1 to take a single temperature 0 (LSB) measurement. The first conversion result of a scan contains temperature information.
PAGE 14
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Table 3. Setup Register BIT NAME BIT FUNCTION — 7 (MSB) — 6 Set to 1 to select setup register. CKSEL1 5 Clock mode and CNVST configuration. Resets to 1 at power-up. CKSEL0 4 Clock mode and CNVST configuration. REFSEL1 3 Reference mode configuration. Set to zero to select setup register. REFSEL0 2 Reference mode configuration.
PAGE 15
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Output Data Format Figures 4–7 illustrate the conversion timing for the MAX1227/MAX1229/MAX1231. The 12-bit conversion result is output in MSB-first format with four leading zeros. DIN data is latched into the serial interface on the rising edge of SCLK. Data on DOUT transitions on the falling edge of SCLK. Conversions in clock modes 00 and 01 are initiated by CNVST.
PAGE 16
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Table 6. Averaging Register BIT NAME BIT — 7 (MSB) Set to zero to select averaging register. FUNCTION — 6 Set to zero to select averaging register. Set to 1 to select averaging register. — 5 AVGON 4 Set to 1 to turn averaging on. Set to zero to turn averaging off. NAVG1 3 Configures the number of conversions for single-channel scans.
PAGE 17
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference the internal oscillator. See Figure 5 for clock mode 01 timing. Performing Conversions in Clock Mode 00 In clock mode 00, the wake-up, acquisition, conversion, and shutdown sequences are initiated through CNVST and performed automatically using the internal oscillator. Results are added to the internal FIFO to be read out later. See Figure 4 for clock mode 00 timing.
PAGE 18
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference CNVST (CONVERSION2) (ACQUISITION1) (ACQUISITION2) CS (CONVERSION1) SCLK DOUT LSB1 MSB1 MSB2 EOC REQUEST MULTIPLE CONVERSIONS BY SETTING CNVST LOW FOR EACH CONVERSION. Figure 5. Clock Mode 01 (CONVERSION BYTE) DIN (UP TO 514 INTERNALLY CLOCKED ACQUISITIONS AND CONVERSIONS) CS SCLK DOUT MSB1 LSB1 MSB2 EOC THE CONVERSION BYTE BEGINS THE ACQUISITION. CNVST IS NOT REQUIRED. Figure 6.
PAGE 19
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference (ACQUISITION1) (CONVERSION1) (ACQUISITION2) CS SCLK DOUT MSB1 LSB1 MSB2 EOC EXTERNALLY TIMED ACQUISITION, SAMPLING AND CONVERSION WITHOUT CNVST. Figure 7.
PAGE 20
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference OUTPUT CODE OUTPUT CODE FULL-SCALE TRANSITION 11 . . . 111 11 . . . 110 11 . . . 101 011 . . . 111 FS = VREF + VCOM 2 011 . . . 110 ZS = COM 000 . . . 010 -VREF + VCOM 2 VREF 1 LSB = 4096 -FS = 000 . . . 001 FS = VREF + VCOM ZS = VCOM V 1 LSB = REF 4096 00 . . . 011 00 . . . 010 000 . . . 000 111 . . . 111 111 . . . 110 111 . . . 101 100 . . . 001 00 . . . 001 100 . . . 000 00 . . .
PAGE 21
12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference 17 REF+ AIN8 9 16 CNVST/AIN15 AIN9 10 15 REF-/AIN14 AIN10 11 14 AIN13 AIN11 12 13 AIN12 Total Harmonic Distortion ⎡ ⎤ THD = 20 x log⎢ ⎛⎝ V22 + V32 + V4 2 + V52 ⎞⎠ / V1⎥ ⎢⎣ ⎥⎦ where V1 is the fundamental amplitude, and V2–V5 are the amplitudes of the first five harmonics. 20 SCLK 19 N.C. AIN2 AIN1 AIN0 N.C. EOC DOUT DIN 26 25 24 23 22 4 18 VDD 5 17 N.C.
PAGE 22
MAX1227/MAX1229/MAX1231 12-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference Revision History REVISION NUMBER REVISION DATE 3 2/10 Removed the A grade products from the Ordering Information table and Electrical Characteristics table.