Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsDev KitsPCB design board

MAX15062B Evaluation Kit Evaluates: MAX15062B

Component List

19-6638; Rev 0; 4/13

Ordering Information appears at end of data sheet.

General Description

The MAX15062B evaluation kit (EV kit) is a fully assem-

bled and tested circuit board that demonstrates the

performance of the MAX15062B 60V, 300mA ultra-small,

high-efficiency, synchronous step-down converter. The

EV kit operates over a wide 6.5V to 60V input voltage

range, and provides up to 300mA at the preset 5V output.

The device features undervoltage lockout, overcurrent

protection, and thermal shutdown. The EV kit switches

at a fixed frequency of 500kHz, and delivers a peak

efficiency of 92% with the supplied components.

The EV kit comes installed with the MAX15062BATA+

in an 8-pin (2mm x 2mm) lead(Pb)-free/RoHS-compliant

TDFN package.

Features

● 6.5Vto60VInputVoltageRange

● 5VOutput,300mAContinuousCurrent

● InternalCompensation

● EN/UVLOforOn/OffControlandProgrammable

InputUndervoltageLockout

● 92%PeakEfficiency

● 500kHzFixed-FrequencyPWMOperation

● PFMorForced-PWMModeofOperation

● HiccupModeOvercurrentProtection

● Open-DrainRESETOutput

● ThermalShutdown

● ProvenPCBLayout

● FullyAssembledandTested

Component Suppliers

Note: Indicate that you are using the MAX15062B when contacting these component suppliers.

DESIGNATION QTY DESCRIPTION

C1 1

22µF, 100V electrolytic capacitor

(8mm x 10.2mm)

PanasonicEEEHA2A220UP

C2 1

1µF ±10%, 100V X7R ceramic

capacitor (1206)

MurataGRM31CR72A105KA

C3 1

1µF ±10%, 6.3V X7R ceramic

capacitor (0603)

MurataGRM188R70J105K

C4 1

10µF ±10%, 6.3V X7R ceramic

capacitor (1206)

MurataGRM31CR70J106K

JU1–JU3 3 2-pin headers

DESIGNATION QTY DESCRIPTION

L1 1

47µH,560mAinductor

Coilcraft,Inc.LPS4018-473ML

R1 1 3.32MΩ±1%resistor(0402)

R2 1 768kΩ±1%resistor(0402)

R3 1 100kΩ±1%resistor(0402)

U1 1

60V, 300mA, ultra-small, high-

efciency,synchronousstep-

downDC-DCconverter(8TDFN)

Maxim MAX15062BATA+

— 3 Shunts

— 1

PCB:MAX15062BEVALUATION

KIT

SUPPLIER PHONE WEBSITE

Coilcraft,Inc. 847-639-6400 www.coilcraft.com

MurataElectronicsNorthAmerica,Inc. 770-436-1300 www.murata-northamerica.com

PanasonicCorp. 800-344-2112 www.panasonic.com

Summary of content (8 pages)

PAGE 1
MAX15062B Evaluation Kit Evaluates: MAX15062B General Description The MAX15062B evaluation kit (EV kit) is a fully assembled and tested circuit board that demonstrates the performance of the MAX15062B 60V, 300mA ultra-small, high-efficiency, synchronous step-down converter. The EV kit operates over a wide 6.5V to 60V input voltage range, and provides up to 300mA at the preset 5V output. The device features undervoltage lockout, overcurrent protection, and thermal shutdown.
PAGE 2
MAX15062B Evaluation Kit Evaluates: MAX15062B Quick Start Detailed Description Recommended Equipment ● MAX15062B EV kit ● 60V adjustable, 0.5A DC power supply ● Electronic load up to 300mA ● Voltmeter Procedure The EV kit is fully assembled and tested. Follow the steps below to verify board operation. Caution: Do not turn on the power supply until all connections are completed. 1) Verify that shunts are installed on jumpers JU1 and JU2 (EN/UVLO).
PAGE 3
MAX15062B Evaluation Kit Evaluates: MAX15062B Active-Low Open-Drain Reset Output (RESET) operation. Keep JU3 open to enable the light-load PFM operation. See Table 2 for proper JU3 configuration. The EV kit provides a PCB pad to monitor the status of the RESET output. RESET goes high when VOUT rises above 95% (typ) of its nominal regulated output voltage. When VOUT falls below 92% (typ) of its nominal regulated voltage, RESET is pulled low. Table 2.
PAGE 4
MAX15062B Evaluation Kit Evaluates: MAX15062B EV Kit Performance Report (continued) LOAD TRANSIENT RESPONSE— PFM OR PWM MODE (LOAD CURRENT STEPPED FROM 150mA TO 300mA) LOAD TRANSIENT RESPONSE— PWM MODE (LOAD CURRENT STEPPED FROM NO LOAD TO 150mA) MAX15062B EV toc07 MAX15062B EV toc06 VOUT (AC) 100mV/div VOUT (AC) 100mV/div IOUT 100mA/div IOUT 100mA/div 20µs/div 20µs/div BODE PLOT MAX15062B EV toc08 50 EN/UVLO 5V/div 40 GAIN (dB) 72 10 36 0 0 -10 -36 -20 IOUT 100mA/div RESET 5V/div
PAGE 5
MAX15062B Evaluation Kit VIN 6.5V TO 60V GND Evaluates: MAX15062B 1 C1 22µF 100V C2 1µF 100V R1 3.32MΩ 1% 1 JU1 2 EN/UVLO VIN LX U1 MAX15062B 2 EN/UVLO GND 8 7 L1 47µH 5V, 300mA C4 10µF 6.3V VOUT GND VOUT 4 1 JU2 2 VCC R2 768kΩ 1% VCC MODE R3 100kΩ VCC 1% C3 1µF 3 V CC RESET 6 RESET MODE 5 1 JU3 2 Figure 1. MAX15062B EV Kit Schematic www.maximintegrated.
PAGE 6
MAX15062B Evaluation Kit Evaluates: MAX15062B 1.0” Figure 2. MAX15062B EV Kit Component Placement Guide— Component Side 1.0” Figure 3. MAX15062B EV Kit PCB Layout—Component Side 1.0” Figure 4. MAX15062B EV Kit PCB Layout—Solder Side www.maximintegrated.
PAGE 7
MAX15062B Evaluation Kit Evaluates: MAX15062B Ordering Information PART TYPE MAX15062BEVKIT# EVKIT #Denotes RoHS compliant. www.maximintegrated.
PAGE 8
MAX15062B Evaluation Kit Evaluates: MAX15062B Revision History REVISION NUMBER REVISION DATE 0 4/13 DESCRIPTION Initial release PAGES CHANGED — For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied.