Datasheet

DESIGNATION QTY DESCRIPTION
U1 1
Power-management IC
(32 TQFN-EP)
Maxim MAX16920BATJ/V+
— 10 Shunts
— 1
PCB: MAX16920B EVALUATION
KIT+
ADDITIONAL COMPONENTS FOR MAX16920A
EVALUATION
— 3
22FF Q10%, 10V X7R ceramic
capacitors (1206)
Murata GRM31CR71A226K
SUPPLIER PHONE WEBSITE
Cooper Bussmann 916-941-1117 www.cooperet.com
Diodes Incorporated 805-446-4800 www.diodes.com
Murata Electronics North America, Inc. 770-436-1300 www.murata-northamerica.com
Panasonic Corp. 800-344-2112 www.panasonic.com
TDK Corp. 847-803-6100 www.component.tdk.com
Vishay 402-563-6866 www.vishay.com
DESIGNATION QTY DESCRIPTION
— 1
47FF Q10%, 10V X7R ceramic
capacitor (1210)
Murata GRM32ER71A476K
— 1
47FH, 1.14A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-470-R
— 1
22FH, 1.68A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-220-R
— 1
10FH, 2.56A inductor
(7.60mm x 7.60mm x 4.35mm)
Cooper Bussmann DRA74-100-R
_________________________________________________________________ Maxim Integrated Products 2
MAX16920B Evaluation Kit
Evaluates: MAX16920A/MAX16920B
Quick Start
Required Equipment
• MAX16920B EV kit
• 12V, 2.5A DC power supply
• Four electronic loads (e.g., HP6060B)
• Four voltmeters
Procedure
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn on
power supplies until all connections are completed.
1) Verify that all jumpers are in their default position, as
shown in Table 1.
2) Adjust the power supply to 12V and connect to the
VIN and PGND PCB pads on the EV kit.
3) Adjust the first load to 150mA and connect to the
OUT1 and PGND1 PCB pads on the EV kit.
4) Connect the first voltmeter to the OUT1 and PGND1
PCB pads on the EV kit.
5) Adjust the second load to 600mA and connect to the
OUT2 and PGND2 PCB pads on the EV kit.
6) Connect the second voltmeter to the OUT2 and
PGND2 PCB pads on the EV kit.
7) Adjust the third load to 1.5A and connect to the OUT3
and PGND3 PCB pads on the EV kit.
8) Connect the third voltmeter to the OUT3 and PGND3
PCB pads on the EV kit.
9) Adjust the fourth load to 150mA and connect to the
OUTA and GND PCB pads on the EV kit.
10) Connect the fourth voltmeter to the OUTA and GND
PCB pads on the EV kit.
11) Connect the SYNC and GND PCB pads on the EV kit
together.
12) Turn on the DC power supply.
13) Enable all loads.
14) Verify that the first voltmeter reads approximately 3.3V.
15) Verify that the second voltmeter reads approximately 5V.
16) Verify that the third voltmeter reads approximately 3.3V.
17) Verify that the fourth voltmeter reads approximately 5V.
Component List (continued)
Component Suppliers
Note: Indicate that you are using the MAX16920B when contacting these component suppliers.