Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsInterface ICsInterface IC - transceivers RS232 2/2 SOIC 16 W

AVAILABLE

Functional Diagrams

Pin Configurations appear at end of data sheet.

Functional Diagrams continued at end of data sheet.

UCSP is a trademark of Maxim Integrated Products, Inc.

For pricing, delivery, and

ordering information, please contact Maxim Direct

at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.

+5V, RS-232 Transceivers

with 0.1µF External Capacitors

Selector Guide

General Description

The MAX200–MAX209/MAX211/MAX213 transceivers

are designed for RS-232 and V.28 communication inter-

faces where Q12V supplies are not available. On-board

charge pumps convert the +5V input to the Q10V needed

for RS-232 output levels. The MAX201 and MAX209

operate from +5V and +12V, respectively, and contain a

+12V to -12V charge-pump voltage converter.

The MAX200–MAX209/MAX211/MAX213 drivers and

receivers meet all EIA/TIA-232E and CCITT V.28 speci-

fications at a 20kbps data rate. The drivers maintain the

Q5V EIA/TIA-232E output signal levels at data rates in

excess of 120kbps when loaded in accordance with the

EIA/TIA-232E specification.

The 5FW shutdown mode of the MAX200, MAX205,

MAX206, and MAX211 conserves energy in battery-pow-

ered systems. The MAX213 has an active-low shutdown

and an active-high receiver enable control. Two receiv-

ers of the MAX213 are active, allowing the ring indicator

(RI) to be monitored easily using only 75FW power.

The MAX211 and MAX213 are available in a 28-pin, wide

small-outline (SO) package and a 28-pin shrink small-

outline (SSOP) package, which occupies only 40% of the

area of the SO. The MAX207 is now available in a 24-pin

SO package and a 24-pin SSOP. The MAX203 and

MAX205 use no external components and are recom-

mended for applications with limited circuit board space.

Next-Generation Device Features

S For Low-Cost Applications:

MAX221E: ±15kV ESD-Protected, +5V, 1µA,

Single RS-232 Transceiver with AutoShutdown™

S For Low-Voltage and Space-Constrained Applications:

MAX3222E/MAX3232E/MAX3237E/MAX3241E/

MAX3246E: ±15kV ESD-Protected, Down

to 10nA, +3.0V to +5.5V, Up to 1Mbps, True

RS-232 Transceivers (MAX3246E Available in

UCSP™ Package)

S For Space-Constrained Applications:

MAX3228E/MAX3229E: ±15kV ESD-Protected,

+2.5V to +5.5V, RS-232 Transceivers in UCSP

S For Low-Voltage or Data Cable Applications:

MAX3380E/MAX3381E: +2.35V to +5.5V, 1µA,

2Tx/2Rx RS-232 Transceivers with ±15kV ESD-

Protected I/O and Logic Pins

S For Low-Power Applications:

MAX3224E–MAX3227E/MAX3244E/MAX3245E:

±15kV ESD-Protected, 1µA, 1Mbps,

+3.0V to +5.5V, RS-232 Transceivers with

AutoShutdown Plus™

Applications

Computers: Laptops, Palmtops, Notebooks

Battery-Powered Equipment

Handheld Equipment

AutoShutdown, AutoShutdown Plus, and UCSP are trademarks of Maxim Integrated Products, Inc.

Ordering Information appears at end of data sheet.

PART

POWER-SUPPLY

VOLTAGE (V)

NUMBER

OF RS-232

DRIVERS

NUMBER

OF RS-232

RECEIVERS

NUMBER OF

RECEIVERS

ACTIVE IN

SHUTDOWN

NUMBER OF

EXTERNAL

CAPACITORS

(0.1µF)

LOW-POWER

SHUTDOWN/TTL

THREE-STATE

MAX200 +5 5 0 0 4 Yes/No

MAX201 +5 and +9.0 to +13.2 2 2 0 2 No/No

MAX202 +5 2 2 0 4 No/No

MAX203 +5 2 2 0 None No/No

MAX204 +5 4 0 0 4 No/No

MAX205 +5 5 5 0 None Yes/Yes

MAX206 +5 4 3 0 4 Yes/Yes

MAX207 +5 5 3 0 4 No/No

MAX208 +5 4 4 0 4 No/No

MAX209 +5 and +9.0 to +13.2 3 5 0 2 No/Yes

MAX211 +5 4 5 0 4 Yes/Yes

MAX213 +5 4 5 2 4 Yes/Yes

19-0065; Rev 7; 12/05

MAX200–MAX209/

MAX211/MAX213

Summary of content (23 pages)

PAGE 1
MAX200–MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors AILABLE AV General Description Next-Generation Device Features The MAX200–MAX209/MAX211/MAX213 transceivers are designed for RS-232 and V.28 communication interfaces where Q12V supplies are not available. On-board charge pumps convert the +5V input to the Q10V needed for RS-232 output levels. The MAX201 and MAX209 operate from +5V and +12V, respectively, and contain a +12V to -12V charge-pump voltage converter.
PAGE 2
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors ABSOLUTE MAXIMUM RATINGS VCC. .........................................................................-0.3V to +6V V+............................................................... (VCC - 0.3V) to +14V V- . ..........................................................................+0.3V to -14V Input Voltages TIN.......................................................... -0.3V to (VCC + 0.3V) RIN. ............................
PAGE 3
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors ELECTRICAL CHARACTERISTICS (continued) (MAX202/MAX204/MAX206/MAX208/MAX211/MAX213: VCC = +5V Q10%; MAX200/MAX203/MAX205/MAX207: VCC = +5V Q5%, C1–C4 = 0.1FF; MAX201/MAX209: VCC = +5V Q10%, V+ = +9.0V to +13.2V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER CONDITIONS MIN TYP 0.8 1.2 Shutdown mode, MAX213, R4, R5 0.6 1.
PAGE 4
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors Typical Operating Characteristics 60kbps 5.8 VCC = +5V ALL Tx OUTPUTS LOADED 3kIIICL TA = +25NC 5.2 5.0 0 12 -SLEW RATE 10 8 6 116kbps 4 2 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 0 5000 1000 2000 3000 4000 LOAD CAPACITANCE (pF) MAX201 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 20kbps 9.0 60kbps 8.5 8.0 VCC = +5V ALL Tx OUTPUTS LOADED 3kIIICL TA = +25NC V+ = 12V 7.5 7.0 0 240kbps VCC = +4.
PAGE 5
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors Detailed Description 0.1FF ISHDN The MAX200–MAX209/MAX211/MAX213 consist of three sections: charge-pump voltage converters, drivers (transmitters), and receivers. Each section is described in detail. +5.5V 0.1FF C1+ VCC C1- MAX200 MAX205 MAX206 MAX211 MAX213 V+ +5V to ±10V Dual Charge-Pump Voltage Converter 0.1FF C2+ 0.1FF C2- +5.5V V0.1FF 400kI T1 T0 T5 TIN +5.
PAGE 6
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors 0.1FF 0.1FF +5V +5V 0.1FF 0.1FF VCC C1+ V+ 0.1FF C1+ VCC V+ C1C2+ MAX200-MAX209 MAX211 MAX213 V- 0.1FF C1C2+ 0.1FF C2- MAX200-MAX209 MAX211 MAX213 V0.1FF 0.1FF +5V C2- 400kI 0.
PAGE 7
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors current typically to 1µA (15µA for the MAX213). The time required to exit shutdown is 1ms, as shown in Figure 5. All receivers except R4 and R5 on the MAX213 are put into a high-impedance state in shutdown mode. The MAX213’s R4 and R5 receivers still function in shutdown mode. These two receivers are useful for monitoring external activity while maintaining minimal power consumption.
PAGE 8
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors Applications Information Capacitor Selection The type of capacitor used is not critical for proper operation. Ceramic capacitors are suggested. To ensure proper RS-232 signal levels over temperature when using 0.1FF capacitors, make sure the capacitance value does not degrade excessively as the temperature varies. If in doubt, use capacitors with a larger nominal value.
PAGE 9
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX200 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 7 8 0.1FF +6.3V 10 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER 0.1FF +6.3V V+ 9 11 0.1FF +16V C2+ 12 +10V TO -10V VOLTAGE INVERTER C2- V- 13 0.1FF +16V +5V TOP VIEW 400kI 5 T1IN T3OUT 1 20 T4OUT T1OUT 2 19 T5IN T2OUT 3 18 N.C.
PAGE 10
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX201 Pin Configurations/Typical Operating Circuit +5V INPUT +9V TO +12V 0.1FF 13 (15) TOP VIEW 1 14 V+ C+ 1 C- 2 13 VCC V- 3 12 GND T2OUT 4 MAX201 R2IN 5 0.1FF +16V V- 11 T1OUT 8 T1IN 1 16 V+ 2 15 VCC V- 3 14 GND T2OUT 4 MAX201 13 T1OUT R2IN 5 R2OUT 12 R1IN 6 11 R1OUT T2IN 7 10 T1IN 8 9 N.C. C2 0.
PAGE 11
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX202 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF +6.3V 0.1FF 16 1 0.1FF +6.3V 3 VCC C1+ V+ 2 +10V 6 -10V +5V TO +10V VOLTAGE DOUBLER C1- 4 TOP VIEW 0.1FF +16V C1+ 1 16 VCC V+ 2 15 GND C1- 3 14 T1OUT C2+ 4 MAX202 12 R1OUT 5 V- 6 11 T1IN T2OUT 7 10 T2IN R2IN 8 9 5 +10V TO -10V VOLTAGE INVERTER C2- V- 0.
PAGE 12
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX203 Pin Configurations/Typical Operating Circuit +5V INPUT TOP VIEW 0.
PAGE 13
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX204 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 6 7 0.1FF +6.3V 9 10 0.1FF +16V 11 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER C2+ +10V TO -10V VOLTAGE INVERTER C2- V+ V- 8 0.1FF +6.3V 12 0.
PAGE 14
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX205 Pin Configuration/Typical Operating Circuit +5V INPUT 0.
PAGE 15
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX206 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 9 10 0.1FF +6.3V 12 13 0.1FF +16V 14 VCC C1+ V+ +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 11 0.1FF +6.3V 15 0.
PAGE 16
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX207 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 9 10 0.1FF +6.3V 12 13 0.1FF +16V 14 C1+ VCC C1- +5V TO +10V VOLTAGE DOUBLER C2+ V+ +10V TO -10V VOLTAGE INVERTER C2- V- 11 0.1FF +6.3V 15 0.
PAGE 17
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX208 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 9 10 0.1FF +6.3V 12 13 0.1FF +16V 14 VCC C1+ V+ 11 0.1FF +6.3V +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 15 0.
PAGE 18
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX209 Pin Configuration/Typical Operating Circuit +5V INPUT 9V - 13.2V INPUT 0.1FF 4 6 0.1FF +16V 7 VCC C+ 5 V+ 8 +10V TO +10V VOLTAGE INVERTER C- 0.1FF +16V +5V TOP VIEW 400kI R1OUT 1 24 T1IN R1IN 2 23 T2IN T1OUT 19 T1 +5V 22 R2OUT GND 3 VCC 4 24 T1IN MAX209 V+ 5 20 T2OUT C+ 6 19 T1OUT C- 7 18 R3IN V- 8 17 R3OUT R5IN 9 16 T3IN R5OUT 10 15 N.C.
PAGE 19
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX211 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 11 12 0.1FF +6.3V 14 0.1FF +6.3V VCC C1+ C1- +5V TO +10V VOLTAGE DOUBLER V+ +10V TO -10V VOLTAGE INVERTER V- 13 15 0.1FF +16V C2+ 16 C2- 17 0.
PAGE 20
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors MAX213 Pin Configuration/Typical Operating Circuit +5V INPUT 0.1FF 11 12 0.1FF +6.3V 14 15 0.1FF +16V 16 0.1FF +6.3V VCC C1+ V+ +5V TO +10V VOLTAGE DOUBLER C1C2+ +10V TO -10V VOLTAGE INVERTER C2- V- 13 17 0.
PAGE 21
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.
PAGE 22
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. 22 PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
PAGE 23
MAX200–MAX209/MAX211/MAX213 +5V, RS-232 Transceivers with 0.1µF External Capacitors Revision History REVISION NUMBER REVISION DATE 6 10/03 Changed the Features section and section information to the Next-Generation Device Features section. 1 7 12/05 Added Note 1 to the Absolute Maximum Ratings section. 2 DESCRIPTION PAGES CHANGED Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.