Datasheet

ManualsBrandsMAXIM INTEGRATED ManualsLinear ICsLinear IC - Op-amp Voltage feedback TSSOP 14

General Description

The MAX4452/MAX4352 single, MAX4453/MAX4353

dual, and MAX4454/MAX4354 quad amplifiers combine

high-speed performance with ultra-low power con-

sumption. The MAX4452/MAX4453/MAX4454 are unity-

gain stable and achieve a -3dB bandwidth of 200MHz,

while the MAX4352/MAX4353/MAX4354 are compen-

sated for a minimum closed-loop gain of +5V/V and

achieve a 80MHz -3dB bandwidth. These devices con-

sume only 620µA of supply current per amplifier.

These amplifiers operate from a +2.7V to +5.25V single

supply and feature rail-to-rail outputs. Along with an

excellent speed/power ratio of 323MHz/mA, these

devices feature a slew rate of 95V/µs and fast 20ns rise

and fall times. These devices are ideal for low-

power/low-voltage systems that require wide bandwidth

such as cell phones and keyless entry systems.

The MAX4452/MAX4352 are available in miniature 5-pin

SC70 and SOT23 packages, while the MAX4453/

MAX4353 are available in tiny 8-pin SOT23, Thin SOT23,

and SO packages. The MAX4454/MAX4354 are avail-

able in space-saving 14-pin TSSOP and SO packages.

________________________Applications

Battery-Powered Instruments

Cellular Telephones

Portable Communications

Keyless Entry

Baseband Applications

Features

♦ Ultra-Low 620µA Supply Current

♦ High Speed (MAX4452/MAX4453/MAX4454)

200MHz -3dB Bandwidth

30MHz 0.1dB Gain Flatness

95V/µs Slew Rate

♦ High Speed (MAX4352/MAX4353/MAX4354)

80MHz -3dB Bandwidth

4MHz 0.1dB Gain Flatness

240V/µs Slew Rate

♦ Single +3V/+5V Operation

♦ Rail-to-Rail Outputs

♦ Ultra-Small SC70-5, SOT23-5, SOT23-8 and Thin

SOT23-8 Packages

MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354

Low-Cost, +3V/+5V, 620µA, 200MHz,

Single-Supply Op Amps with Rail-to-Rail Outputs

________________________________________________________________ Maxim Integrated Products 1

19-1824; Rev 1; 1/05

Ordering Information

PA R T

T EM P RA N G E

PIN - PA C K A G E

TO P

M A R K

M A X4 4 5 2 E X K- T

- 40° C to + 85° C

5 S C 70- 5ABI

M AX 4452E U K- T

- 40° C to + 85° C

5 S OT23- 5

AD O V

M A X4 4 5 3 E KA- T

- 40° C to + 85° C

8 S OT23- 8

AAD S

M AX 4453E Z A- T

- 40° C to + 85° C 8 Thi n S O T23- 8

AAAB

M AX 4453E S A

- 40° C to + 85° C

8 S O—

M A X4 4 5 4 E U D

- 40° C to + 85° C

14 TS S O P —

M AX 4454E S D

- 40° C to + 85° C

14 S O —

M A X4 3 5 2 E X K- T

- 40° C to + 85° C

5 S C 70- 5

ABJ

M AX 4352E U K- T

- 40° C to + 85° C

5 S OT23- 5

AD OW

M A X4 3 5 3 E KA- T

- 40° C to + 85° C

8 S OT23- 8

AAD T

M AX 4353E S A

- 40° C to + 85° C

8 S O—

M A X4 3 5 4 E U D

- 40° C to + 85° C

14 TS S O P —

M AX 4354E S D

- 40° C to + 85° C

14 S O —

PART

NO.

AMPS

MIN

GAIN

BANDWIDTH

(MHz)

SLEW

RATE

(V/µs)

MAX4452

1 1 200 95

MAX4352

1 5 400 240

MAX4453

2 1 200 95

MAX4353

2 5 400 240

MAX4454

4 1 200 95

MAX4354

4 5 400 240

Selector Guide

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

Typical Operating Characteristic

Pin Configurations appear at end of data sheet.

MAX4452/3/4 toc01

0.40

0.45

0.55

0.50

0.70

0.75

0.65

0.60

0.80

SUPPLY CURRENT (mA)

2.7 3.5 3.93.1

4.3

4.7 5.1 5.5

SUPPLY VOLTAGE (V)

SUPPLY CURRENT vs.

SUPPLY VOLTAGE (PER AMPLIFIER)

Summary of content (19 pages)

PAGE 1
9-1824; Rev 1; 1/05 Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs The MAX4452/MAX4352 single, MAX4453/MAX4353 dual, and MAX4454/MAX4354 quad amplifiers combine high-speed performance with ultra-low power consumption. The MAX4452/MAX4453/MAX4454 are unitygain stable and achieve a -3dB bandwidth of 200MHz, while the MAX4352/MAX4353/MAX4354 are compensated for a minimum closed-loop gain of +5V/V and achieve a 80MHz -3dB bandwidth.
PAGE 2
MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354 Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs ABSOLUTE MAXIMUM RATINGS Supply Voltage (VCC to VEE)..................................................+6V Differential Input Voltage ......................................................2.5V IN_-, IN_+, OUT_..............................(VCC + 0.3V) to (VEE - 0.3V) Current into Input Pins (IN_+, IN_-) ..................................
PAGE 3
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs (V CC = +5V, V EE = 0, V CM = +1.75V, R L = 1kΩ to V CC /2, A VCL = +1V/V (MAX4452/MAX4453/MAX4454), A VCL = +5V/V (MAX4352/MAX4353/MAX4354), TA = +25°C, unless otherwise noted.) PARAMETER Small Signal -3dB Bandwidth Large Signal -3dB Bandwidth Bandwidth for 0.1dB Flatness Slew Rate Rise/Fall Time SYMBOL BWSS BWLS BW0.
PAGE 4
MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354 Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs AC ELECTRICAL CHARACTERISTICS (continued) (V CC = +5V, V EE = 0, V CM = +1.75V, R L = 1kΩ to V CC /2, A VCL = +1V/V (MAX4452/MAX4453/MAX4454), A VCL = +5V/V (MAX4352/MAX4353/MAX4354), TA = +25°C, unless otherwise noted.
PAGE 5
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs (V CC = +5V, V EE = 0, V CM = +1.75V, R L = 1kΩ to V CC /2, A VCL = +1V/V (MAX4452/MAX4453/MAX4454), A VCL = +5V/V (MAX4352/MAX4353/MAX4354), TA = +25°C, unless otherwise noted.) PARAMETER SYMBOL Two-Tone, Third-Order Intermodulation Distortion CONDITIONS MIN TYP f1 = 2MHz, f2 = 2.1MHz MAX -65 UNITS dBc Input Noise-Voltage Density en f = 10kHz 15 nV/√Hz Input Noise-Current Density in f = 10kHz 0.
PAGE 6
Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.75V, AVCL = +1V/V (MAX4452/MAX4453/MAX4454), AVCL = +5V/V (MAX4352/MAX4353/MAX4354), RL = 1kΩ to VCC/2, CL = 5pF, TA = +25°C, unless otherwise noted.
PAGE 7
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs MAX4352/MAX4353/MAX4354 LARGE-SIGNAL PULSE RESPONSE MAX4452/MAX4453/MAX4454 SMALL-SIGNAL PULSE RESPONSE MAX4452/3/4 toc13 MAX4352/MAX4353/MAX4354 SMALL-SIGNAL PULSE RESPONSE MAX4452/3/4 toc14 MAX4452/3/4 toc15 RL = 150Ω RL = 150Ω INPUT 50mV/div INPUT 200mV/div INPUT 10mV/div OUTPUT 50mV/div OUTPUT 1V/div OUTPUT 50mV/div 50ns/div 50ns/div MAX4352/MAX4353/MAX4354 LARGE-SIGNAL PULSE RESPONSE MAX4452/3/4 toc16 C
PAGE 8
Typical Operating Characteristics (continued) (VCC = +5V, VEE = 0, VCM = +1.75V, AVCL = +1V/V (MAX4452/MAX4453/MAX4454), AVCL = +5V/V (MAX4352/MAX4353/MAX4354), RL = 1kΩ to VCC/2, CL = 5pF, TA = +25°C, unless otherwise noted.) COMMON-MODE REJECTION vs. FREQUENCY VOLTAGE NOISE DENSITY vs.
PAGE 9
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs MAX4352/MAX4353/MAX4354 POWER-UP TIME MAX4452/MAX4453/MAX4454 POWER-UP TIME ISOLATION RESISTANCE vs. CAPACITIVE LOAD MAX4452/3/4 toc33 MAX4452/3/4 toc32 MAX4452/3/4 toc31 30 28 26 5V 5V VSUPPLY VSUPPLY RISO (Ω) 24 0 0 22 20 18 1.5V 16 1.5V VOUT VOUT 14 0 12 0 10 0 50 100 500ns/div 500ns/div INPUT BIAS CURRENT vs. TEMPERATURE INPUT OFFSET CURRENT vs. TEMPERATURE 150 CLOAD (pF) 0.7 0.6 0.5 0.4 0.
PAGE 10
MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354 Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs Pin Description PIN NAME 10 FUNCTION MAX4452 MAX4352 MAX4453 MAX4353 MAX4454 MAX4354 1 — — OUT Amplifier Output 2 4 11 VEE Negative Power Supply 3 — — IN+ Noninverting Amplifier Input 4 — — IN- Inverting Amplifier Input 5 8 4 VCC Positive Power Supply — 1 1 OUTA — 2 2 INA- Amplifier A Inverting Input — 3 3 INA+ Amplifier A Noninverting
PAGE 11
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs The MAX4452/MAX4352 single, MAX4453/MAX4353 dual, and MAX4454/MAX4354 quad, single-supply, railto-rail, voltage-feedback amplifiers achieve high slew rates and wide bandwidths while consuming only 620µA per amplifier. Excellent speed/power ratio makes them ideal for portable devices and high-frequency signal applications.
PAGE 12
MAX4452/MAX4453/MAX4454/MAX4352/MAX4353/MAX4354 Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs RG RG RF RF IN VOUT VOUT RS IN RO RO VOUT = (RF / RG) VIN VOUT = [1+ (RF / RG)] VIN RS Figure 3b. Inverting Gain Configuration Figure 3a.
PAGE 13
• Use surface-mount instead of through-hole components for better high-frequency performance. • Use a PC board with at least two layers; it should be as free from voids as possible. • Keep signal lines as short and as straight as possible. Do not make 90° turns; round all corners.
PAGE 14
Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) SC70, 5L.
PAGE 15
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs DIM A A1 B C e E H L N E H INCHES MILLIMETERS MAX MIN 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 BSC 0.150 0.157 0.228 0.244 0.016 0.050 MAX MIN 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 BSC 3.80 4.00 5.80 6.20 0.40 SOICN .EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 1.
PAGE 16
Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) SOT-23 5L .
PAGE 17
Low-Cost, +3V/+5V, 620µA, 200MHz, Single-Supply Op Amps with Rail-to-Rail Outputs CL E MIN MAX A A1 A2 0.90 0.00 0.90 1.45 0.15 1.30 b 0.28 0.45 C D E 0.09 2.80 2.60 0.20 3.00 3.00 SYMBOL CL CL E1 E1 1.50 L 0.30 L2 e PIN 1 I.D. DOT (SEE NOTE 6) SOT23, 8L .EPS SEE DETAIL "A" e b 1.75 0.60 0.25 BSC. 0.65 BSC. 1.95 REF. e1 0 0 8 e1 D C CL L2 A A2 GAUGE PLANE A1 SEATING PLANE C 0 L NOTE: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2.
PAGE 18
Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) TSSOP4.40mm.
PAGE 19
Package Information (continued) 8LTHIN SOT.EPS (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.