Datasheet

DESIGNATION QTY DESCRIPTION
C1, C2, C3 3
0.1FF Q10%, 16V X7R ceramic
capacitors (0603)
Murata GRM188R71C104KA01D
C4 1
4.7FF Q10%, 10V X5R ceramic
capacitor (0603)
TDK C2012X5R1A475K/0.85
C5 1
10FF Q10%, 10V X5R ceramic
capacitor (0603)
TDK C2012X5R1A106K/1.25
C6 1
1FF Q10%, 10V X7R ceramic
capacitor (0603)
TDK C1608X7R1A105K
C7 1
0.01FF Q10%, 16V X7R ceramic
capacitor (0603)
Murata GRM188R71C103KA01D
F1 1
4.7FF EMI filter (3-terminal
capacitor)
Murata NFM21PC475B1A3D
J1 1 6-pin right-angle male header
J2 1 8-pin (2 x 4) straight male header
J3, JP1,
JP2, JP3
4 3-pin straight male headers
DESIGNATION QTY DESCRIPTION
Q1 1
2.2A, 30V p-channel MOSFET
(3 SOT23)
Vishay Si2303CDS
R1–R5 5
4.7kI Q1% resistors (0603)
R6, R7 2
150I Q5% resistors (0603)
R8 1
7.5kI Q1% resistor (1206)
R9 1
845I Q1% resistor (1206)
R10 1
4.02kI Q1% resistor (0603)
R11 1
402I Q1% resistor (0603)
R12 1
8.06kI Q1% resistor (0603)
R13 1
0.2I Q1%, 2W current-sense
resistor (2512)
Stackpole CSRN2512FKR200
R14, R15 2
10kI Q5% resistors (0603)
U1 1
Low-cost, 8-bit DAC (5 SOT23)
Maxim MAX5380MEUK+
U2 1
Current-sense amplifier with
12-bit ADC (10 FMAX
M
)
Maxim MAX9611AUB+
— 3 Shorting jumpers
— 1 PCB: EPCB9611PM1
SUPPLIER PHONE WEBSITE
Murata Electronics North America, Inc. 770-436-1300 www.murata-northamerica.com
TDK Corp. 847-803-6100 www.component.tdk.com
Vishay 402-563-6866 www.vishay.com
PIN SIGNAL DESCRIPTION
1 N.C. Not connected
2 N.C. Not connected
3 SCL I
2
C serial clock
4 SDA I
2
C serial data
5 GND Ground
6 VCC Power supply
_________________________________________________________________ Maxim Integrated Products 2
MAX9611PMB1 Peripheral Module
Component List
Component Suppliers
Note: Indicate that you are using the MAX9611PMB1 when contacting these component suppliers.
µMAX is a registered trademark of Maxim Integrated Products,
Inc.
Detailed Description
I
2
C Interface
The MAX9611PMB1 peripheral module can interface to
the host in one of two ways. It can plug directly into a
Pmod-compatible port (configured for I
2
C) through con-
nector J1, or in this case, other I
2
C boards can attach to
the same I
2
C bus through connector J2.
I
2
C Interface (Daisy-Chaining Modules)
Alternatively, the peripheral module can connect to other
I
2
C-based Pmod modules using a 4-conductor ribbon
cable connecting to the J2 connector. In this situation,
pins 1-4 and 5-8 on J2 provide two connections to the
I
2
C bus, allowing the module to be inserted into an I
2
C
bus daisy-chain.
Connector J1 provides connection of the module to the
Pmod host. The pin assignments and functions adhere
to the Pmod standard recommended by Digilent. See
Table 1.
Table 1. Connector J1 (I
2
C Communication)