Installation Guide

ManualsBrandsMAXIMAL ManualsPower ControllersMAXIMAL Maximal FDV Series Dual Power Supply Access Power Controllers

Maximal11FDV

- Power Supply 1:

12VDC @ 3.3A or 24VDC @ 3.6A.

- Power Supply 2:

12VDC @ 3.3A or 24VDC @ 3.6A.

- Sixteen (16) PTC protected outputs.

Maximal33FDV

- Power Supply 1:

12VDC @ 5.3A or 24VDC @ 5.6A.

- Power Supply 2:

12VDC @ 5.3A or 24VDC @ 5.6A.

- Sixteen (16) PTC protected outputs.

Maximal55FDV

- Power Supply 1: 12VDC @ 9.3A.

- Power Supply 2: 12VDC @ 9.3A.

- Sixteen (16) PTC protected outputs.

Maximal75FDV

- Power Supply 1: 12VDC @ 9.3A.

- Power Supply 2: 24VDC @ 9.6A.

- Sixteen (16) PTC protected outputs.

Maximal77FDV

- Power Supply 1: 24VDC @ 9.6A.

- Power Supply 2: 24VDC @ 9.6A.

- Sixteen (16) PTC protected outputs.

Maximal FDV Series

Dual Power Supply

Access Power Controllers (PTC)

Models Include:

Rev. DFDV031115

More than just power.

Installing Company: _______________ Service Rep. Name: __________________________________

Address: _____________________________________________ Phone #: __________________

Installation Guide

Summary of content (16 pages)

PAGE 1
Maximal FDV Series Dual Power Supply Access Power Controllers (PTC) Models Include: Maximal11FDV - Power Supply 1: 12VDC @ 3.3A or 24VDC @ 3.6A. - Power Supply 2: 12VDC @ 3.3A or 24VDC @ 3.6A. - Sixteen (16) PTC protected outputs. Maximal33FDV - Power Supply 1: 12VDC @ 5.3A or 24VDC @ 5.6A. - Power Supply 2: 12VDC @ 5.3A or 24VDC @ 5.6A. - Sixteen (16) PTC protected outputs. Maximal55FDV - Power Supply 1: 12VDC @ 9.3A. - Power Supply 2: 12VDC @ 9.3A. - Sixteen (16) PTC protected outputs.
PAGE 2
Table of Contents: MaximalFDV Series Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 MaximalFDV Series Configuration Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Maximal Series Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 ACM8CB Access Power Controller Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
MaximalFDV Series Overview: Altronix MaximalFDV Access Power/Controllers distribute and switch power to access control systems and accessories. They convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into sixteen (16) independently controlled 12VDC or 24VDC PTC protected outputs. Outputs are activated by an open collector sink or normally open (NO) dry trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc.
PAGE 4
MaximalFDV Series Features: ACM8CB Access Power Controller Modules: • Sixteen (16) independently trigger controlled outputs. Output options: a) Sixteen (16) Fail-Safe filtered power outputs. b) Sixteen (16) Fail-Secure filtered power outputs. c) Any combination of the above. • Sixteen (16) Access Control System trigger inputs. Input trigger options: a) Sixteen (16) normally open (NO) dry trigger inputs. b) Sixteen (16) open collector inputs. c) Any combination of the above.
PAGE 5
MaximalFDV Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, the Canadian Electric Code, Part I, Part II and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. Power Supply Board LED Diagnostics (pg. 7) Access Power Controller LED Diagnostics (pg. 7) Power Supply Board Terminal Identification (pg. 7) Access Power Controller Terminal Identification (pg.
PAGE 6
8. ACM8CB Fire Alarm Interface options (Figs. 5-9, pg. 12): A normally closed [NC] or normally open [NO] input trigger from a fire alarm control panel or a polarity reversal input from an FACP signaling circuit will affect selected outputs. To enable FACP Disconnect for an output turn the corresponding switch(es) [SW1-SW8] OFF on each ACM8CB board. To disable FACP disconnect for an output turn the corresponding switch(es) [SW1-SW8] ON on each ACM8CB board.
PAGE 7
Maintenance: Unit should be tested at least once a year for the proper operation as follows: FACP Supervision: To ensure proper connection and operation of the Fire Alarm disconnect hookup. Please follow the appropriate procedure below: Normally Open Input: Placing a short between terminals marked [T] and [+ INP] will trigger the Fire Alarm Disconnect. Remove the short to reset. Normally Closed Input: Removing the wire from terminal marked [INP –] will trigger the Fire Alarm Disconnect.
PAGE 8
Power Supply Board Terminal Identification: Terminal Legend L, N + DC – Trigger EOL Supervised NO, GND RESET + AUX – Function/Description Connect 220VAC, 50/60Hz to these terminals: L to hot, N to neutral. Do not use terminal marked [G]. Factory connected to ACM8CB board. Fire Alarm Interface trigger input from a short or FACP. Trigger inputs can be normally open, normally closed from an FACP output circuit (Fig. 3, pg. 10). FACP interface latching or non-latching (Fig. 3, pg. 10).
PAGE 9
Power Supply Board Output Voltage Settings: Fig. 1 Fig. 1a ON SW1 ON OFF - 24V ON - 12V + DC --- OFF - 24V ON - 12V Access Power Controller Typical Application Diagram (for each ACM8CB): Fig. 2 Fig. 2a Intact = Dry Input Cut = Wet Input Normally Open (N.O.) Door Releasing Device FACP (Fire Alarm Control Panel) FACP Keypad Access Control Panel TRG C Fig.
PAGE 10
Fig.
PAGE 11
NEC Power-Limited Wiring Requirements: Power-limited and non power-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25” away from any non power-limited circuit wiring. Furthermore, all power-limited circuit wiring and non power-limited circuit wiring must enter and exit the cabinet through different conduits. One such example of this is shown below. Your specific application may require different conduit knockouts to be used.
PAGE 12
FACP Hook-Up Diagrams: Fig. 5 Optional hook-up using two (2) isolated power supply inputs (Only applicable on Maximal11FDV): Fig. 6 Polarity reversal input from FACP signaling circuit output (polarity is referenced in alarm condition): CUT JUMPER CUT JUMPERS J1 AND J2 FACP TRG J1 INTERFACE J2 ISOLATED POWER INPUT 12 OR 24 VAC OR VDC (ACM8 POWER) Fig.
PAGE 13
Notes: Maximal11FDV/33FDV/55FDV/75FDV/77FDV Series Installation Guide - 13 -
PAGE 14
Notes: - 14 - Maximal11FDV/33FDV/55FDV/75FDV/77FDV Series Installation Guide
PAGE 15
Enclosure Dimensions (H x W x D approximate): 26” x 19” x 6.25” (660.4mm x 482.6mm x 158.8mm) 19” (482.6mm) 4” (101.6mm) 7” (177.8mm) 4” (101.6mm) 2” (50.8mm) 6.25” (158.8mm) 2” (50.8mm) 19” (482.6mm) 8.9” (226.1mm) 8.4” (213.4mm) 0.85” (21.6mm) 7” (177.8mm) 8.5” (215.9mm) 8.4” (213.4mm) 0.85” (21.6mm) 1.25” (31.75mm) 2” (50.8mm) 1” (25.4mm) 8.9” (226.1mm) 6.25” (158.8mm) 0.85” (21.6mm) 26” (660.4mm) 7” (177.8mm) 4” (101.6mm) 26” (660.4mm) 1.0” (25.4mm) 7.5” (190.
PAGE 16
eFlow Power Supply/Chargers can be Controlled and Monitored while Reporting Power/Diagnostics from Anywhere over the Network... LINQ2 - Network Communication Module LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up and running at optimal levels.