R TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY GUIDELINES KEY PARTS DIAGRAM TECHNICAL INFORMATION TYPES OF NAILS OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING EXPLODED VIEW PARTS LIST WARRANTY NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-888-670-6682.
4 R model no. 058-9844-2 | contact us 1-888-670-6682 SAFETY GUIDELINES TECHNICAL SPECIFICATIONS MAGAZINE CAPACITY up to 100 nails NAILS 34° clipped-head (paper strip) nails (2–3 1/2") with the following diameters: 0.113, 0.120, 0.131" (2.87, 3.05, 3.33 mm); smooth/ring /screw OPERATING PRESSURE 70–120 PSI (4.8–8.3 bar) AVERAGE AIR CONSUMPTION 0.09 CF/cycle @ 90 PSI AIR INLET 1/4"–18 NPT WEIGHT 8 lb 10 oz (3.
6 R model no. 058-9844-2 | contact us 1-888-670-6682 Safety guidelines • Do not use oxygen or any other combustible or bottled gas to power air-powered tools. Failure to observe this warning can cause an explosion and serious personal injury or death. Use only the compressed air to power airpowered tools. Use a minimum of 25' (7.6 m) of hose to connect the tool to the compressor. Failure to comply will result in serious injury or loss of life. • Risk of electric shock. Do not expose a compressor to rain.
8 R model no. 058-9844-2 | contact us 1-888-670-6682 Potential hazard that may result in moderate injury or damage to equipment. Always ensure that the tool has stopped before connecting it to the air supply. Do not wear watches, rings, bracelets, or loose clothing when using any air tool. Do not overload the tool. Allow the tool to operate at its optimum speed for maximum efficiency. Do not use a tool that is leaking air, with missing or damaged parts, or that requires repairs.
10 R model no. 058-9844-2 | contact us 1-888-670-6682 No. Description No. Description 1 Trigger 4 Magazine pusher latch 2 Magazine 5 Safety tip 3 Air inlet plug 6 Depth adjustment dial Compatible compressors GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with MAXIMUM® air-powered tools. The compressor should be able to supply a minimal air delivery of 5.
12 R model no. 058-9844-2 | contact us 1-888-670-6682 Wood density >0.6 g/cm3 ≤0.6 g/cm3 Nail size Compressor air pressure <2 1/2" (63 mm) 100 PSI (7 bar) ≥2 1/2" (63 mm) 110 PSI (7.6 bar) <2 1/2" (63 mm) 70 PSI (5 bar) ≥2 1/2" (63 mm) 110 PSI (7.6 bar) NOTE: Please note that the filter-regulator-lubricator and air hose are sold separately. WARNING! Potential hazard that could result in serious injury or loss of life.
14 R model no. 058-9844-2 | contact us 1-888-670-6682 This lightweight MAXIMUM® Air-powered Clipped-head Framing Nailer drives 2 to 3 1/2" (50 to 90 mm) long clipped-head framing nails. Loading Nails Fig. C Operation Acceptable Nails Length: 2 to 3 1/2" (50 to 90 mm) 1. Disconnect the tool (1) from the air supply (2) (Fig. C). Angle: 34° 1 2 3 1/2” （90 mm） 2” (50 mm) Fig. A 34° Fig. B This nailer can be used with a variety of shank types (e.g.
16 R model no. 058-9844-2 | contact us 1-888-670-6682 Operation Mode 3. Insert a strip of nails into the magazine. Ensure the points of the nails are facing down. Be sure to insert the heads of the nails into the channel. Release pusher (1) to push nails forward until it comes to the end. The tool is now ready for use (Fig. E). (See nail type icon on page 14.) 1 Fig. E Fig. F 2 1 2 4. Plug in compressor, turn it on and set the pressure regulator to 90 PSI (6.2 bar).
18 R model no. 058-9844-2 | contact us 1-888-670-6682 • Weather Operation Fig. H Adjusting the Nail Depth When operating any air-powered tool below freezing temperature： For varying materials, the nail depth can be adjusted tool-free with the depth adjustment dial (Fig. H). Fig. I • Increasing Nail Penetration Depth • Verify the compressor tank have been properly drained prior to use. Keep tool as warm as possible using any safe, convenient method.
20 R model no.
22 R model no. 058-9844-2 | contact us 1-888-670-6682 Troubleshooting PROBLEM POSSIBLE CAUSES SOLUTIONS The following chart lists common issues and solutions. Please read it carefully and follow all instructions closely. The tool does not operate properly–it does not drive the nail or operates sluggishly. 1. The air supply is inadequate. 2. Lubrication is inadequate. 3. The O-rings or seals are worn or damaged. 4. The exhaust port in the cylinder head is blocked. 1.
24 R model no. 058-9844-2 | contact us 1-888-670-6682 No. Description No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Screw Screw Spring Washer Washer Exhaust Cover Cylinder Cap Gasket Spring Valve O-ring O-ring O-ring Valve Seat Stopped Washer 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Screw Collar Cylinder Seal Cylinder O-ring Restrictive Plate O-ring O-ring Piston Assembly Bumper A Bumper B Circlip Bushing Body No. Description No.
26 model no. 058-9844-2 | contact us 1-888-670-6682 This MAXIMUM product is guaranteed for a period of 5 years from the date of original retail purchase against defects in workmanship and materials only and is subject to the following components: a) Component A: The carrying case is guaranteed for a period of 1-year from the date of original retail purchase against defects in workmanship and materials.
28 R model no. 058-9844-2 | contact us 1-888-670-6682 Additional Limitations This warranty applies only to the original purchaser and may not be transferred. In addition to the 5-Year Limited Warranty, this MAXIMUM product is covered by our: This warranty applies for a period of 5 years from the date of original retail purchase, as indicated on the bill of sale.
