Owners Manual

ManualsBrandsMaxLite ManualsLampingMaxLite Single 18 Watt White T8 Bi Pin (G13) LED Bulb - 5000K

Operating Instructions L13T8EX4xx & L18T8EX4xx Series

MaxLite External LED T8 - 4FT

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

Page: 1

REV: 11/22/17

General Safety Information

WARNING - Risk of fire or electric shock. Luminaire wiring and electrical parts

may be damaged when drilling for installation of LED retrofit kit. Check for enclosed

wiring and components.

WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires

knowledge of luminaires electrical systems. If not qualified, do not attempt

installation. Contact a qualified electrician.

WARNING - Risk of fire or electric shock. Install this kit only in luminaires that have the

construction features and dimensions shown in the photographs and/or drawings and

where the input rating of the retrofit kit does not exceed the input rating of the luminaire.

Only those open holes indicated in the photographs and/or drawings may be made or altered as a

result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other

sharp objects.

Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder

terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical

connections to lampholder lead wires by employing applicable connectors.

THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.

The LED tube are intended to retrofit surface mount, Type IC or non-IC recessed mount Listed

fluorescent luminaires that use maximum 4 straight tubular lamps with or without a diffuser, the

minimum dimension of luminaries are tabulated below:

NOTE: The external T8 lamps can be installed single-ended or double-ended.

(See page 2 for single-ended installation or page 3 for double-ended.)

The products are intended to be used in dry and damp locations only.

Summary of content (4 pages)

PAGE 1
Operating Instructions L13T8EX4xx & L18T8EX4xx Series MaxLite® External LED T8 - 4FT General Safety Information WARNING - Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components. WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
PAGE 2
Operating Instructions L13T8EX4xx & L18T8EX4xx Series MaxLite® External LED T8 - 4FT Installation & Operation - Single-Ended Wiring Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock. Step 1: Make sure the circuit breaker that supplies power to the fixture is turned off. Step 2: Remove lens or diffusion cover on the lighting fixture.
PAGE 3
Operating Instructions L13T8EX4xx & L18T8EX4xx Series MaxLite® External LED T8 - 4FT Installation & Operation - Double-Ended Wiring Disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off using the light switch is not sufficient to prevent electrical shock. Step 1: Make sure the circuit breaker that supplies power to the fixture is turned off. Step 2: Remove lens or diffusion cover on the lighting fixture.
PAGE 4
Operating Instructions L13T8EX4xx & L18T8EX4xx Series MaxLite® External LED T8 - 4FT Warranty Information MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.