Owners Manual

ManualsBrandsMaxLite ManualsLampingMaxLite Single 9 Watt DirectFit White T8 Bi Pin (G13) LED Bulb - 3500K

Operating Instructions LED T8 DirectFit Series - 4FT (Metal End Caps)

MaxLite LED T8 DirectFit Lamps

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION

CAUTION – RISK OF FIRE. DO NOT INSTALL THIS LAMP IN A PRE-HEAT LUMINAIRE.

CAUTION – RISK OF FIRE. USE ONLY PLACE OF FLUORESCENT LAMPS

SPECIFIED ON LABEL.

THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS. IF LAMP DOES NOT

LIGHT WHEN THE LUMINAIRE IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE

AND CONTACT LAMP MANUFACTURER OR QUALIFIED ELECTRICIAN.

DIRECT REPLACEMENT FOR THE FOLLOWING LAMPS ONLY 4ft MEDIUM BI-PIN T8 FLUORESCENT LAMPS

32W/48T8, 30W/48T8, 28W/48T8, 25W/48T8

CAUTION - RISK OF FIRE. IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION (BUZZING,

FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND CONTACT

MANUFACTURER.

SUITABLE FOR DAMP LOCATIONS.

THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.

SEE MAXLITE.COM FOR BALLAST COMPATIBILITY.

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

Page: 1

REV: 11/06/17

Safety

ati

Installation Instructions

1. Turn off the power to the luminaire. (Fig. 1)

2. Remove diffuser (if provided).

3. Remove the existing fluorescent lamps from the

luminaire. Verify the fluorescent tube type is listed on

the label of MaxLite LED T8 DirectFit lamp. (Fig. 2)

4. Dispose the existing fluorescent lamps in

accordance with government regulations in your area.

5. Install MaxLite LED T8 DirectFit lamps. Ensure that

the pins are firmly seated in the lampholders. (Fig. 3)

6. Replace diffuser (if removed in step 2).

7. Switch on power to the luminaire. (Fig. 4)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and (2)this device must accept any interference

received, including interference that may cause undesired operation

Product image is for illustrative purposes

only and may differ from the actual product.

Summary of content (4 pages)

PAGE 1
Operating Instructions LED T8 DirectFit Series - 4FT (Metal End Caps) MaxLite® LED T8 DirectFit Lamps General Safety Information READ AND FOLLOW ALL SAFETY INSTRUCTIONS DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION CAUTION – RISK OF FIRE. DO NOT INSTALL THIS LAMP IN A PRE-HEAT LUMINAIRE. CAUTION – RISK OF FIRE. USE ONLY PLACE OF FLUORESCENT LAMPS SPECIFIED ON LABEL. THIS LAMP ONLY OPERATES ON ELECTRONIC BALLASTS.
PAGE 2
Operating Instructions LED T8 DirectFit Series - 4FT (Metal End Caps) MaxLite® LED T8 DirectFit Lamps Warranty Information MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.
PAGE 3
CONSIGNES D’INSTALLATION LAMPES DIRECFIT T8 DEL DE MAXLITE SÉRIES - 4 PIEDS (EMBOUT MÉTALLIQUE) MaxLite® Lampes DirectFit T8 Del De MaxLite Informations générales de sécurité LIRE ET SUIVRE TOUTES LES CONSIGNES DE SÉCURITÉ DANGER – RISQUE DE DÉCHARGE ÉLECTRIQUE – DÉBRANCHER AVANT TOUTE INSTALLATION ATTENTION – RISQUE D’INCENDIE. NE PAS INSTALLER CETTE LAMPE DANS UN LUMINAIRE AVEC PRÉCHAUFFAGE. CETTE LAMPE NE PEUT ÊTRE UTILISÉE QU’AVEC DES BALLASTS ÉLECTRONIQUES.
PAGE 4
CONSIGNES D’INSTALLATION LAMPES DIRECFIT T8 DEL DE MAXLITE SÉRIES - 4 PIEDS (EMBOUT MÉTALLIQUE) MaxLite® Lampes DirectFit T8 Del De MaxLite Informations sur la garantie MaxLite Inc.