Owners Manual

ManualsBrandsMaxLite ManualsCeiling LightsMaxLite Utility Wrap Single Light 24" Wide Integrated LED Flush Mount - 4000K - On/Off Motion Sensor

Operating Instructions LSU Series

MaxLite LED Utility Wrap Fixture

12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

Page: 1

REV: 05/03/18

General Safety Information

• To reduce the risk of death, personal injury or property damage from fire,

electric shock, falling parts, cuts/abrasions, and other hazards read all

warnings and instructions included with and on the fixture box and all

fixture labels.

• Before installing, servicing, or performing routine maintenance upon

this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires

should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or

maintenance of the luminaires, consult a qualified licensed electrician

and check your local electrical code.

• DO NOT INSTALL DAMAGED PRODUCT!

• This fixture is intended to be connected to a properly installed and grounded

UL listed junction box.

WARNING:

RISK OF ELECTRICALSHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture

to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label

information.

• Make all electrical and grounded connections in accordance with the National Electrical

Code and any applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION:

RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing,

servicing or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

CAUTION:

RISK OF FIRE

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.

• MIN 90°C SUPPLY CONDUCTORS.

Models: LSU Series

Picture is for illustration purposes

only. Your model may vary.

Summary of content (8 pages)

PAGE 1
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 2
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture General Wiring Diagram CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply. Connecting panels to AC source supply: All units must be individually connected to the AC supply.
PAGE 3
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Mounting Instructions Before installation, ensure if power supply is disconnected. Cables must be connected in accordance to instruction and proper standing rules. 5. For rear access points feed wires through hole. 6. Using 1” mounting screw or 3”x3/16 toggle bolts, secure fixture in place using keyhole slots provided. Lens Cover N L Driver Screw 7. After making wiring connections, replace wire cover and diffuser into place. 8.
PAGE 4
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Optional Motion Sensor Lens Access Screws Upper Housing Lower Housing Coupling Assembly Stand offs Mounting Key Holes Motion Sensor Option Wiring © Copyright 2018. MaxLite, Inc. All Rights Reserved. 12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.
PAGE 5
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Setting & Adjusting Motion Sensor To make setting and control adjustments, you will need to access the three rotary DIP controls behind the lens. Control Mode H The LOD-500 series features 8 different control modes for selection via rotary DIP switch. Please refer to the following table and sensor operation charts to select the desired control mode. SW.
PAGE 6
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Battery Backup Option (Continued) READ AND FOLLOW ALL SAFETY INSTRUCTIONS! 1. To prevent high voltage from being present on yellow & orange output leads prior to installation, converter connector must be open. Do not join converter connector until installation is complete and AC power is supplied to the emergency driver. 2. This product is for use with an emergency LED lighting load and supplies up to 8.
PAGE 7
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Fixture Your fixture comes with an additional housing on rear to enclose the battery back up unit Side View Housing BBU Step Down Transformer (347V Only) Note: not suitable for BBU models. 1. Location of SDT. Driver SDT CAUTION: Always disconnect power to luminaire before attaching, removing or servicing. Risk of shock or fire. © Copyright 2018. MaxLite, Inc. All Rights Reserved.
PAGE 8
Operating Instructions LSU Series MaxLite® LED Utility Wrap Fixture Warranty Information MaxLite Inc. warrants its products for a minimum period of FIVE (5) years from the date of original purchase from MaxLite or its authorized distributor/dealer (the “Warranty Period”), as follows: If a Product fails to operate during the Warranty Period as a result of defects in materials or workmanship, MaxLite will, at its option, repair it, replace it with the same or like Product.