Owner's Manual

ManualsBrandsMaxLite ManualsCeiling LightsMaxLite LSU GEN3 Single Light 48-3/4" Wide Integrated LED Flush Mount Ceiling Light

12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.com

Page : 1

REV: 01/13/16

Operating Instructions LSU Series

MaxLite

LED UTILITY WRAP FIXTURES

General Safety Information

• To reduce the risk of death, personal injury or

property damage from fire, electric shock, falling

parts, cuts/abrasions, and other hazards read all

warnings and instructions included with and on

the fixture box and all fixture labels.

• Before installing, servicing, or performing routine

maintenance upon this equipment, follow these

general precautions.

• Commercial installation, service and

maintenance of luminaires should be performed

by a qualified licensed electrician.

• For Residential installation: If you are unsure

about the installation or maintenance of the

luminaires, consult a qualified licensed

electrician and check your local electrical code.

• DO NOT INSTALL DAMAGED PRODUCT!

• This fixture is intended to be connected to a properly

installed and grounded UL listed junction box.

WARNING:

RISK OF ELECTRICALSHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• Make all electrical and grounded connections in accordance with the National Electrical Code and any

applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

CAUTION:

RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or

performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

CAUTION:

RISK OF FIRE

• Keep combustible and other materials that can burn away from luminaire and lamp/lens.

• MIN 90°C SUPPLY CONDUCTORS.

Picture is for illustration purposes only. Your model may vary.

Summary of content (8 pages)

PAGE 1
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES General Safety Information • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels. • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
PAGE 2
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES General Wiring Diagram CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply. Connecting panels to AC source supply: All units must be individually connected to the AC supply.
PAGE 3
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Mounting Instructions-Cont’d 3. Select wiring access point and remove appropriate knockout. 4. Select installation point and locate studs. 5. For rear access points feed wires through hole. 6. Using 1” mounting screw or 3”x3/16 toggle bolts, secure fixture in place using keyhole slots provided. 7. After making wiring connections, replace wire cover and diffuser into place. 8.
PAGE 4
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Optional Motion Sensor MOTION SENSOR OPTION WIRING: © Copyright 2016. MaxLite, Inc. All Rights Reserved. 12 York Ave, West Caldwell, NJ 07006 Tel: 973-244-7300 Fax: 973-244-7333 Email: info@maxlite.
PAGE 5
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Setting and adjusting the Motion Sensor To make setting and control adjustments, you will need to access the three rotary DIP controls behind the lens. Default parking profile Default Stair profile Please note, your control is equipped with a quality neoprene seal. This seal does expand over time providing maximum sealing protection possible.
PAGE 6
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Battery Back Up Option-Cont’d: READ AND FOLLOW ALL SAFETY INSTRUCTIONS! Installation Instructions 1. To prevent high voltage from being present on yellow & orange output leads prior to installation, converter connector must be open. Do not join converter connector until installation is complete and AC power is supplied to the emergency driver. 2. This product is for use with an emergency LED lighting load and supplies up to 8.
PAGE 7
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Fixture Your fixture comes with an additional housing on rear to enclose the battery back up unit Housing Step Down Transformer (347V – 240V) BBU 1. Location of SDT. Driver SDT CAUTION: Always disconnect power to luminaire before attaching, removing or servicing. Risk of shock or fire. © Copyright 2016. MaxLite, Inc. All Rights Reserved.
PAGE 8
Operating Instructions LSU Series MaxLite® LED UTILITY WRAP FIXTURES Warranty LIMITED WARRANTY FOR CERTAIN MAXLITE® LED LIGHTING FIXTURES, SPECIFICALLY LED TROFFERS; TROFFER RETROFITS; PANEL LUMINAIRES; DOWNLIGHTS; HIGH BAY; WRAP AND VAPOR TIGHT; PLUG & PLAY LIGHT BARS; EXIT SIGNS.