User manual

Toolbox 32 User Manual 1.47d www.cse-semaphore.com/mykingfisher
Page
271
RTU Data - Port Registers
Port Registers contain the configuration parameters and communication statistics for the ports configured in
the RTU. Most of these registers are read / write which means they can be changed while the RTU is running
by using ladder logic. For the following registers, nn is the port number (1-16) and cc is the register channel
where applicable.
Configuration Parameters
#YPMODnn
The type of module (PC-1/CP-x/MC-x) and port number (1-3) configured for port
nn.
CP-x P1= 30, PC-1 P1 = 45, MC-x P1 = 59, CP-x P2= 94, PC-1 P2 = 109, MC-x
P2 = 123, CP-x P3= 158, MC-x P3 = 187, CP-x P4 = 222.
Read/Write
#YPADDRnn
Slot Address (1-64) of the module containing port nn
Read/Write
#YPTYPnn
Port Type. 0=RS232, 1=RS485, 2=Radio, 3=Pline, 4=PSTN, 5=TMR,
6=RADIO_HOT, 9=RS422, 8=Mobitex, 10=Ethernet, 11=Video, 12=RS232
RADIO, 13=MicroX RADIO, 14=GPS Internal, 15=GPS External, 16=Line-2.
Read/Write
#YPSPnn
(300 - 57600, 65535=115200 bps) Port Speed
Read/Write
#YPPREnn
Pre-Tx Delay (ms)
Read/Write
#YPP
OSnn
Post-Tx Delay (ms)
Read/Write
#YPPCOLnn
Port protocol.
Series 2 = 0; ADS Data Logger = 7; Allen Bradley = 21; ALERT = 71;
Alstrom Relay = 50; ASCII No Parity = 43; ASCII Even Parity = 53; BCL
ARC Device = 52; Conitel = 80; Cooper = 64; DATAC = 14; Datataker =
46; Datran DT300 = 58; DNP-
3 (all settings) = 38; DV1000 = 34; Form 4C
= 6; FUJI Micrex-F = 29; FUJI NJ Series = 36; GE CCM = 26; GE SNP-X
= 47; GE T60 Relay = 51; Genisys = 44; Genisys Master = 81; GPS = 49;
GPS NMEA = 76; HART = 23; IDEC PLC = 48; INLINE = 17; INLINE2 =
55; INTRAC = 16; JZA Train Control = 41; MAC-800 = 10; Mercury = 28;
Microtran = 11; Mier Transposer = 62; Minitran = 12; G&F Minitran = 18;
MTran Host = 33; Mbus ASCII Init = 66; Mbus init, S2 = 2; Mbus
init&resp, S2 = 2; Mbus SCADA, S2 = 2; Mbus slave, S2 = 1; Mbus
init&parity = 130; Mbus init&resp&par = 130; Mbus SCADA&parity = 129;
Mbus slave&parity = 129; Modem Sw Unit = 15; Monitor WeatherStn =
45; Multitrode 2PC = 25; NEC DCU = 22; OMRON = 19; PEEK = 74;
Remote Data Logger = 39; S1 Ctrl, Mbus, S2 = 0; S1 Outstn, S2 = 0; S1
Ctrl, no CRC, S2 = 4; S1 Out, no CRC, S2 = 4; SER_SSPA = 77; Shaft
Encoder = 20; Simatic TI = 72; SM6615 = 78; STIC Gauge = 27;
Tandberg = 63; Traffic Light Controller = 61; TRIO Eseries = 70; TS5000
= 30; User-Defined (all settings) = 57; YSI Logger = 42.
Read/Write