MAINTENANCE MANUAL FOR WHEELCHAIR LIFT MODEL NO. WL7 DOT-Public Use Lift PATENTS PENDING © MAXON Lift Corp. 2005 MP-04-03 REV.
PATENTS PENDING
11921 Slauson Ave. Santa Fe Springs, CA. 90670 LIFT CORP. CUSTOMER SERVICE: TELEPHONE (562) 464-0099 TOLL FREE (800) 227-4116 FAX: (888) 771-7713 NOTE: For latest version of all Manuals (and replacements), download the Manuals from Maxon’s website at www.maxonlift.com.
TABLE OF CONTENTS SAFETY SUMMARY ............................................................................................................ 6 LIFT COMPONENTS & TERMINOLOGY ............................................................................... 8 MAINTENANCE SCHEDULE ........................................................................................... 10 CHECKING HYDRAULIC FLUID LEVEL............................................................................. 11 CHANGING HYDRAULIC FLUID ....
PLATFORM ASSEMBLY .................................................................................................... 44 HYDRAULIC COMPONENTS ............................................................................................. 48 12 VDC POWER UNIT ........................................................................................................ 50 ELECTRICAL COMPONENTS ........................................................................................... 52 DECALS AND DECAL PLACEMENT ..
SAFETY SUMMARY Comply with the following WARNINGS and safety precautions while maintaining the Wheelchair Lift. See Operator’s Manual MP-04-02 for operating safety requirements. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Read and understand the instructions in this Maintenance Manual before performing maintenance on the Lift. 2. Before operating the Lift, read and understand the operating instructions contained in Operator’s Manual MP-04-02. 3.
11921 Slauson Ave. Santa Fe Springs, CA.
LIFT COMPONENTS & TERMINOLOGY 12 INBOARD 8 RIGHT 5 13 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 12 8 9 3 10 14 6 2 11 1 7 LEFT 3 14 4 LIFT COMPONENTS (SEE TABLE 9-1) FIG.
NAME THRESHHOLD PLATE 2. OUTBOARD ROLLSTOP 3. SEAT BELT 4. PLATFORM 5. HANDRAILS 6. INBOARD ROLLSTOP 7. 8. ELECTRICAL ACTUATOR HYDRAULIC CYLINDER 9. HYDRAULIC POWER UNIT (COVER IS SHOWN) 10. LIFT CONTROLLER 11. 12. BASE THRESHHOLD WARNING BEACON 13. THRESHHOLD WARNING ALARM 14. PLATFORM LIGHTS DESCRIPTION Component that bridges the entry way, through the Lift, into the vehicle. Detects if that portion of Lift is occupied during "UP/DOWN" operation between vehicle floor and the ground.
MAINTENANCE SCHEDULE NOTE: The Lift Controller counts the number of cycles & lifts over the lifetime of the Lift. One CYCLE is counted each time the Lift is unfolded from the stowed position to floor level, lowered to the ground, raised to floor level, and then stowed. One LIFT is counted each time the Lift is lowered from floor level to the ground, and raised back to floor level.
CHECKING HYDRAULIC FLUID LEVEL Keep dirt, water and other contaminants from entering the hydraulic system. Before opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up contaminants that can get in the openings. Also, protect the openings from accidental contamination. NOTE: WL7 may be equipped with 1 of 2 different sizes of Reservoir. To make sure you have correct fluid level, measure length of Reservoir before checking fluid level. FILLER CAP 1.
CHANGING HYDRAULIC FLUID CAUTION Keep dirt, water and other contaminants from entering the hydraulic system. Before opening the hydraulic fluid reservoir filler cap, drain plug and hydraulic lines, clean up contaminants that can get in the openings. Also, protect the openings from accidental contamination. PUMP COVER 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Unbolt the Pump Cover and remove it from the Lift as shown in FIG. 12-1.
4. Bolt the Reservoir on the Pump. (FIG. 13-1). Reconnect tubes to barb fittings on the Reservoir. TUBE BARBED FITTINGS 5. Pull out (no threads) Filler Cap (FIG. 12-2). Fill the Reservoir with Hydraulic Fluid (TABLE 13-1) to level (“FL1”) you measured in step 2. Reinstall Filler Cap (FIG. 12-2) TUBE RESERVOIR R ECOMMEN D ED H YD R AU LIC FLU ID B R AN D PAR T N U MB ER ROSEMEAD THS FLUID 17111 EXXON UNIVIS HVI 26 PUMP BOLTS (4 PLACES) UNBOLTING / BOLTING RESERVOIR (LH PUMP SHOWN) FIG.
ADJUSTMENTS MAT SWITCH ADJUSTMENT ILLUMINATED POWER SWITCH 1. Make sure power switch (FIG. 14-1A) is turned on and illuminated. Lower Lift to the ground (FIG. 14-1A). 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1/4” LIFT AT GROUND LEVEL FIG. 14-1A HEIGHT MEASUREMENT (RH SIDE SHOWN) FIG. 14-1B 2. Measure the height of the Threshhold Plate as shown in (FIG. 14-1B). If the height is not 1/4”, do step 3. If the height is already 1/4”, skip step 3, and go on to step 4.
THRESHOLD WARNING BEACON ADJUSTMENT SCREW THRESHHOLD PLATE BASE PLATE ADJUSTING SWITCH FIG. 15-1B RH SIDE OF LIFT FIG. 15-1A CW UNTIL ALARM & BEACONS TURN ON 5. Step on Threshhold Plate. Warning Alarm and Beacons should activate. If the Warning Alarm and Beacons do not activate, turn Adjustment Screw (FIG. 15-1B) clockwise (FIG. 15-2) a little. Repeat until Warning Alarm and Beacons activate when you step on Threshhold Plate and turn off when you step off Threshhold Plate.
PLATFORM TILT ADJUSTMENT NOTE: The platform tilt adjustment is important for operation of the Outboard Rollstop and for keeping Platform level when it reaches the ground. Vehicle floor height, Lift installation angle, and stiffness of the Vehicle suspension may change the angle of Platform on the ground. 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 NOTE: For the following procedure, ground level is where the Outboard Rollstop is first fully opened for crossing. 1.
ILLUMINATED POWER SWITCH 1. Make sure power switch (FIG. 17-1) is turned on and illuminated. Unfold the Lift (FIG. 17-1). LIFT AT FLOOR LEVEL FIG. 17-1 OUTBOARD ROLLSTOP 2. Loosen hex nut (FIG. 17-2) on OUTBOARD ROLLSTOP adjustment screw. Turn OUTBOARD ROLLSTOP adjustment screw counter-clockwise (FIG. 17-3) until the screw breaks contact with switch actuator and Controller reading is OUTBD SW (FIG. 17-4). ADJUSTMENT SET SCREW HEX NUT OUTBOARD ROLLSTOP FIG.
GROUND SWITCH ADJUSTMENT 1. Make sure power switch (FIG. 18-1) is illuminated and turned on. Lower Lift to the ground (FIG. 18-1). ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 LIFT AT GROUND LEVEL FIG. 18-1 CONTROLLER NOTE: When using the Manual Pump, first make sure the notches are lined up vertically on tip of the Manual Backup Handle. Then make sure Handle is fully engaged with Manual Pump before you start pumping with the Handle.
3” ADJUSTMENT SCREW PLATFORM 3” ABOVE GROUND FIG. 19-1 CCW UNTIL CONTROLLER READS “GROUND” CW UNTIL CONTROLLER READS “UP” GROUND SWITCH ADJUSTMENT SCREW FIG. 19-2 4. Raise the lift to Vehicle Floor level (FIG. 19-4). Then lower the Lift to the ground (FIG. 18-1). Controller should display GROUND (FIG. 193) . GROUND CONTROLLER READING PLATFORM AT GROUND LEVEL FIG. 19-3 5. Use the Manual Pump (FIG. 18-2) to raise the Lift so the top surface of Platform is 3” above ground (FIG. 19-1). Controller (FIG.
STOW SWITCH ADJUSTMENT 1. Make sure power switch (FIG. 20-1) is turned on and illuminated. Stow the Lift (FIG. 20-1). ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 STOWED LIFT (PUMP ON LH SIDE ) FIG. 20-1 2. Open the pressure release valve (FIG. 20-2) counter-clockwise with the Backup Pump Handle. As the Lift starts to unfold and rests against the latches (FIG. 20-3), close the pressure release valve (FIG. 20-2) clockwise).
3. Remove cover from top of tower (FIG. 21-1A). ADJUSTMENT SCREW JAM NUT LIFT TO REMOVE 4. Loosen jam nut (FIG. 21-1B) on the STOW switch adjust COVER ment screw. Then turn adjustment screw 1/2 turn clockLIFT WITH LH PUMP wise (FIG. 21-2). (LH TOWER SHOWN) FIG. 21-1A STOW SWITCH ADJUSTMENT FIG. 21-1B 5. Repeat step 1 to stow the Lift and check the Platform in the stowed position. CW - 1/2 TURN STOW SWITCH ADJUSTMENT SCREW FIG. 21-2 6. When adjustment is complete, tighten jam nut (FIG.
STAR (*) SWITCH ADJUSTMENT 1. Make sure power switch (FIG. 22-1) is turned on and illuminated. Stow the Lift (FIG. 22-1). ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 STOWED LIFT (PUMP ON LH SIDE ) FIG. 22-1 PRESSURE RELEASE VALVE BACKUP PUMP HANDLE 2. Open the pressure release valve (FIG. 22-2) counter-clockwise with the Backup Pump Handle. As the Lift starts to unfold and rests against the latches (FIG.
ADJUSTMENT SCREW 3. Remove cover from top of tower (FIG. 23-1A). JAM NUT LIFT TO REMOVE 4. Loosen jam nut (FIG. 23-1B). Turn the STAR (*) switch adjustment screw until Lift Controller displays STOWED * COVER (FIG. 23-2). LIFT WITH LH PUMP (RH TOWER SHOWN) FIG. 23-1A STAR (*) SWITCH ADJUSTMENT FIG. 23-1B 5. Next turn the STAR (*) switch adjustment screw (FIG. 23-3) another 1/2 turn clockwise. Then tighten jam nut (FIG. 23-1B). STOWED* CONTROLLER READING PLATFORM STOWED & STAR SWITCH ACTIVATED FIG.
FOLD SWITCH ADJUSTMENT NOTE: The FOLD switch adjustment screw is always on the same side of the Lift as the Pump Cover. ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 1. Make sure power switch (FIG. 24-1) is turned on and illuminated. Make sure Controller is reading FLOOR (FIG. 24-2) before going to the next step. LIFT AT FLOOR LEVEL FIG. 24-1 FLOOR CONTROLLER READING PLATFORM AT FLOOR LEVEL FIG.
UNFOLD. CONTROLLER READING PLATFORM STOPPED BEFORE FOLDING FIG. 25-1 NOTE: When using the Manual Pump, first make sure the notches are lined up vertically on tip of the Manual Backup Handle. Then make sure Handle is fully engaged with Manual Pump before you start pumping with the Handle. See the Operation Manual for more information on operating the Manual Pump. MANUAL PUMP BACKUP PUMP HANDLE 4. Use the Backup Pump (FIG.
FOLD SWITCH ADJUSTMENT - Continued 5. Remove cover from top of tower (FIG. 26-1A). ADJUSTMENT SCREW HEX NUT LIFT TO REMOVE 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 COVER 6. Loosen hex nut (FIG. 26-1B) and cap screw. Turn adjustment screw clockwise or counter-clockwise as required (FIG. 26-2) until Controller reads FOLD (FIG. 26-3). LIFT WITH LH PUMP (LH TOWER SHOWN) FIG. 26-1A CAP SCREW FOLD SWITCH ADJUSTMENT FIG.
UNFOLD UP DOWN HAND CONTROL FIG. 27-1 NOTE: Watch the Controller readings as the Platform starts folding. 8. Push FOLD on the Hand Control (FIG. 27-1). Controller reading should be FOLD. (dot) as shown in FIG. 27-2. FOLD. CONTROLLER READING PLATFORM STARTS MOVING TO FOLD FIG. 27-2 LOWER ARM ROLLER 9. Before the roller on the Platform Closer Arm touches the lower Parallel Arm (FIG. 27-3), Controller reading should change to FOLD (FIG. 27-4). PLATFORM CLOSER ARM LIFT WITH LH PUMP (RH TOWER SHOWN) FIG.
FLOOR SWITCH ADJUSTMENT NOTE: The Platform FLOOR switch adjustment screw is always on the opposite side of the Lift from the Pump Cover. 1. Make sure power switch (FIG. 28-1) is turned on and illuminated. Stow the Lift (FIG. 28-1). ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 STOWED LIFT (PUMP ON LH SIDE ) FIG. 28-1 2. Use hand control (FIG. 28-2) to UNFOLD Lift to vehicle floor level. Then lower the Lift DOWN to ground level.
6. Loosen hex nut and cap screw (FIG. 29-1B). Turn adjustment screw clockwise to decrease the overlap and counter-clockwise to increase the overlap (FIG. 29-2). Repeat steps 1 - 3 to check alignment of the edges of the Inboard Rollstop and Base Plate (FIG. 15-3). ADJUSTMENT SCREW CAP SCREW HEX NUT LIFT TO REMOVE COVER LIFT WITH LH PUMP (RH TOWER SHOWN) FIG. 29-1A FLOOR SWITCH ADJUSTMENT FIG.
PRESSURE SWITCH ADJUSTMENT (IF EQUIPPED) NOTE: Before doing this procedure, make sure vehicle battery is fully charged. An undercharged battery can make Lift operate incorrectly. 1. Make sure power switch (FIG. 30-1) is turned on and illuminated. UNFOLD Platform and then lower it DOWN to the ground (FIG. 30-1). PLATFORM AT “FOLD” (STOWED) POSITION ILLUMINATED POWER SWITCH 11921 Slauson Ave. Santa Fe Springs, CA.
LOAD 50 LBS. PLATFORM AT FLOOR LEVEL INBOARD ROLLSTOP PLATFORM WITH 50 LB. LOAD FIG. 31-1 4. If the Platform starts folding with the 50 pound load, stop folding Platform. Then UNFOLD Platform to vehicle floor level as shown in FIG. 30-1. Controller reading should be FLOOR (FIG. 30-3) . OCCUPIED CONTROLLER READING OCCUPIED PLATFORM AT FLOOR LEVEL FIG. 31-2 SCREWS 5. Remove Pump Cover (FIG. 31-3). PUMP COVER FLAT WASHERS (3 PLACES) BOLTING/ UNBOLTING THE PUMP COVER (LH PUMP SHOWN) FIG.
PRESSURE SWITCH ADJUSTMENT (IF EQUIPPED) - Continued FLAT TIP SCREWDRIVER 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 6. Turn the Pressure Switch set screw (FIG. 321B) counter-clockwise a little at a time. Try to FOLD platform using Hand Control. Release FOLD Switch if platform starts to fold. Then, UNFOLD platform to vehicle floor level (FIG. 32-2). Repeat this step until platform will not fold with the 50 pound load and Controller reading is OCCUPIED (FIG. 32-3).
PLATFORM WITHOUT LOAD FIG. 33-1 PLATFORM AT “FOLD” (STOWED) POSITION PLATFORM AT GROUND LEVEL 8. FOLD the Platform to stowed position. (FIG. 33-2). Controller reading should be FOLD (FIG. 33-3) while Lift is folding and STOWED * (FIG. 33-4) when Lift is stowed and interlock is on. FOLDING & UNFOLDING PLATFORM FIG. 33-2 FOLD CONTROLLER READING PLATFORM FOLDING FIG. 33-3 STOWED* CONTROLLER READING PLATFORM STOWED & INTERLOCK ON FIG. 33-4 33 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
PRESSURE SWITCH ADJUSTMENT (IF EQUIPPED) - Continued 9. UNFOLD Platform and then lower it DOWN to the ground (FIG. 34-1). Then raise the Lift and FOLD it to stowed position (FIG. 34-1).Make sure Lift operates correctly as it unfolds, lowers, raises, and folds. PLATFORM AT “FOLD” (STOWED) POSITION 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 PLATFORM AT GROUND LEVEL FOLDING & UNFOLDING PLATFORM FIG. 34-1 10. Reinstall the Pump Cover (FIG. 34-2).
PARTS BREAKDOWN 4 6 5 4 6 4 5 6 5 5 6 5 6 5 2 1 3 6 4 5 6 1 3 6 5 SEE PLATFORM ASSY ITEM QTY. PART NO. 1 2 905005 2 1 DESCRIPTION RETAINING RING, 3/4" 265038-03 SHAFT, 36" LG. 265038-04 SHAFT, 39" LG. 3 2 261321 4 4 267110-01 PINCH SHIELD, PLASTIC 5 8 902000-5 FLAT WASHER, #10 6 8 904002-2 RIVET, 5/15" IDIA. X 0.565" LG. SPACER 35 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
MAIN ASSEMBLY-2 30 9A 9A 11921 Slauson Ave. Santa Fe Springs, CA.
ITEM QTY. PART NO. 1 1 900009-5 DESCRIPTION 2 2 900009-3 CAP SCREW, 5/16"-18 X 3/4" LG, GRADE 8 3 1 266755-01 HANDRAIL ASSEMBLY, LH 3A 1 904004-3 RIVET, 0.156" DIA X 0.550" LG. 3B 1 905019 3C 1 905314-01 C AP BUMPER 4 3 901001 5 7 902000-7 6 2 906414-01 CABLE CLAMP 7 2 904004-3 RIVET, 0.156" DIA X 0.550" LG.
LH PLATFORM CLOSER ARM 4 2 15 11 14 1 12 11 10 6 13 18 16 17 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO. 1 1 266621-01 2 2 265017 3 1 904701-02 SELF LOCKING PIN 4 1 266901-01 ACTUATOR ASSEMBLY 5 1 904004-3 RIVET 6 1 902000-4 FLAT WASHER, #8 7 1 906414-01 CABLE CLAMP, PLASTIC 8 1 900009-2 CAP SCREW, 5/16"-18 X 1" LG, GRADE 8 9 1 902000-7 FLAT WASHER, 5/16" 10 1 266545-02 BEARING 11 2 903409-05 FLAT WASHER, 1/2" X 1-1/4" O.D. 12 1 900005-6 BUTTON SCREW, 1/4"-20 X 1-1/2" LG.
MAIN ASSEMBLY-3 5 30 31 REFER TO MAIN ASSEMBLY-2, ITEM 32 2 29 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO. 1 2 900009-3 CAP SCREW, 5/16"-18 X 3/4" LG, GRADE 8 UPPER ARM ASSEMBLY (BEARINGS INCLUDED) 2 DESCRIPTION 1 266609-01 2A 4 265072 SELF LUBE BEARING 2B 1 901005 HEX NUT, 5/16"-18, GRADE 8 2C 1 903006-1 SET SCREW, 5/16"-18 X 1" LG. 1 266756-01 HANDRAIL ASSEMBLY RH RIVET, .0156" DIA. X 0.550" LG.
MAIN ASSEMBLY-4 4 24 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO. 1 3 900001-11 BUTTONHEAD SCREW, 5/16"-18 X 5/8" LG. 2 7 902000-7 FLAT WASHER, 5/16" 266827-01 COVER ASSEMBLY, LH 3 1 266828-01 COVER ASSEMBLY, RH 904002-2 RIVET, 3/16" DIA. X 0.565" LG. 266605-01 MAIN FRAME (FOR 30" WIDE PLATFORM) 266605-02 MAIN FRAME (FOR 33" WIDE PLATFORM) 4 4 5 1 DESCRIPTION 6 2 266852-01 LATCH SUPPORT PIN 7 2 908027-01 SLEEVE BEARING, 1/2" I.D.
PLATFORM ASSEMBLY 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. 1 1 PART NO. DESCRIPTION 266714-01 OUTROLL RAMP, 30" 266714-02 OUTROLL RAMP, 33" 2 1 900023-4 SCREW, PAN HD, 8-32 X1/2" LG. (STAINLESS) 3 1 903107-01 HEX NUT, 8-32 4 2 903402-02 FLAT WASHER, 3/4", NYLON 5 2 266719-02 SWIVEL NUT, THIN HEX, 1/2" 6 2 266545-04 BEARING 7 2 266893-02 ROLLER FLANGED 8 4 903409-04 FLAT WASHER, 1/2", 1-1/8" O.D. (STAINLESS) 9 4 903409-01 FLAT WASHER, 9/32", 1" O.D.
PLATFORM ASSEMBLY - Continued 41C 41 41D 41A 41B 41E 41D 46 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO. 31 2 902013-09 32 3 901000 33 3 900005-5 BUTTON SCREW 1/4"-20 X 1-1/4" LG. 34 2 266623-01 PLATFORM STOP 35 5 905070-01 CABLE TIE HOLDER 36 5 904004-3 RIVET, 0156" DIA. X .550 LG. 37 2 900009-6 CAP SCREW, 5/16"-18 X 1-1/2" LG.
HYDRAULIC COMPONENTS 13 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO. DESCRIPTION 1 2 906718-01 2 1 261351 HOSE ASSEMBLY, 27" LG. (1/8" I.D.) 3 1 261350 HOSE ASSEMBLY, 63" LG. (1/8" I.D.) 4 1 905026 TEE FITTING, JIC#4 M-M-F 5 1 905027 ELBOW FITTING, JIC#4 M-F 6 1 905250 TEE, SWIVEL BRANCH NUT, JIC 1/4" 7 1 450017 FITTING, STRAIGHT THREAD, O-RING, #6- JIC#4 8 1 905249 SWIVEL, 1/4" JIC-1/4" NP, FEMALE- 9 2 905024 ELBOW FITTING, MALE #10-32 - 1/4," BARB 10 1 224370-05 HOSE, PLASTIC, 52-1/2" LG. (1/8" I.D.
12 VDC POWER UNIT 13 7 11 10 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 8 6 9 HEX NUT (REF) 4 9B 3 2 9A 5 12 CAUTION 1 A small amount of torque is required for tightening the hex nut on Cartridge Valve, Item 9B. Torque the Cartridge Valve hex nut to 30 LB.-IN. Overtightening hex nut may damage Cartridge Valve.
QTY. PART NO. DESCRIPTION R EF 1 266950-01 PUMP ASSEMBLY, WL7 1 1 265117-02 RESERVOIR, 2 QT.
ELECTRICAL COMPONENTS 3 2 NOTE: Before disconnecting or connecting Hand Control, roll back sleeve from connector to gain access to connector lock. 13 1 16 5 17 4 11921 Slauson Ave. Santa Fe Springs, CA.
QTY. PART NO.
DECALS AND DECAL PLACEMENT DECAL (ALARM) DECAL “C” DECAL “A” DECAL “O” DECAL “K” DECAL “B” 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 SERIAL PLATE DECAL “F” DECAL “L” DECAL “M” DISPLAY OVERLAY DECAL “I” DECAL“J” DECAL “G” DECAL“N” DECAL “P” DECAL “D” DECAL “E” DECAL“N” DECAL “H” All WARNING, CAUTION, and OPERATION decals provided with Wheelchair Lift must always be in place on the Lift and Vehicle (see FIG. 52-1), and must always be legible.
11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECAL SET P/N 266704-01 FIG.
DECALS AND DECAL PLACEMENT - Continued HAND CONTROL & HANGER MOUNTING DECAL “J” DECAL “I” DECAL “A” 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 DECAL “C” DECAL “B” CABLE HOOK DOOR TYPICAL PLACEMENT OF DECALS ON VEHICLE FIG.
ANTI-SLIP & SAFETY STRIPING YELLOW TAPE (BOTTOM-ROLLSTOP) PN 905293-17 ANTI-SLIP TAPE (ROLLSTOP) PN 096015-10 ANTI-SLIP TAPE (TOP-ROLLSTOP) PN 096012-10 ANTI-SLIP TAPE PN 096014-10 ANTI-SLIP TAPE PN 096013-10 YELLOW TAPE (OUTBOARD) PN 905293-11 YELLOW TAPE (OUTBOARD) PN 905293-14 YELLOW TAPE (THRESHOLD PLATE) PN 905293-12 YELLOW TAPE (INBOARD) PN 905293-16 YELLOW TAPE PN 905293-11 YELLOW TAPE PN 905293-14 YELLOW TAPE (INBOARD & OUTBOARD) PN 905293-13 57 PATENTS PENDING 11921 Slauson Ave.
ANTI-SLIP & SAFETY STRIPING - Continued (33” WIDE PLATFORM) 11921 Slauson Ave. Santa Fe Springs, CA.
SYSTEM DIAGRAMS FLOW CONTROL VALVE - .5 GPM FLOW CONTROL VALVE - .5 GPM CYLINDER CYLINDER PRESSURE TRANSDUCER PRESSURE PORT MANUAL RELEASE VALVE MANUAL BACK-UP PUMP S.V.2 S.V.1 .2 GPM RETURN RETURN M 102 GEAR PUMP R.V. SET @ 1850 PSI FILLER BREATHER FIG. 59-1 59 PATENTS PENDING 11921 Slauson Ave. Santa Fe Springs, CA.
ELECTRICAL SYSTEM DIAGRAM 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 SWITCH CONTACT CONFIGURATIONS & LEGENDS FIG.
