Installation Notes

PARKING AIR HEATER
30
6.3.4 Power mode operation 6.3.6 Setting time
The power mode has 5 levels (P1-P5), "P1" is the minimum power
level (lowest fuel consumption), P5 is the maximum power level
(highest fuel consumption). Press the " " or " " key to adjust
the power level, which will be displayed on a bar graph.
Fig.28
Long press the " " key to enter power mode/temperature mode,
and select the power mode. "P1" will be displayed, as
Fig.28.
6.3.5 Temperature (thermostat) mode operation (Auto)
Long press the " " key to enter power mode/temperature
mode, select the temperature mode to show the Celsius symbol,
and press the " " or " " keys to adjust the temperature, which
can be set in the range of 5°C - 30°C.
1）Press the " " or " " key to select whether to set the
start-up time or shut-down time. (Displaying "ON" signifies
start-up, "OFF" signifies shut-down.)
3) Press the " " and " " keys to adjust the time value. The time
range is 1-24 hours and minimum adjustment is 10 minutes.
5) Long press the " " key for 2 seconds to erase the settings
and exit the interface.
7) Starting the timing function:
Long press the " " and " " keys to start the timing function.
This will start the timed start-up in the shut-down state, or the
timed shut-down in the operating state. Short press the " "
key to see the remaining time.
6) Long press the " "+" "keys for 2 seconds to exit the timing
setup interface.
OK
2)Press the " " key to enter the selected mode.
OK
4) Press the " " key to save the settings and exit the interface.
OK
Press the " " + " " keys at the same time for 2 seconds to
enter the timing setup interface. The display will show "10.1 hours"
and a flickering " " icon, which means that the start-up time
is being set. If the display shows "OFF", it means the shut-down
time is being set.
OK
6.3 LCD Panel Switch Functions
6.3.1 Manual pump operation(Pump_oil)
DO NOT cut off the power supply to the heater during the
cooling process, or its internal temperature will remain too
high, causing deformation of the combustion chamber. This
deformation may result in insufficient air entering the
combustion chamber, causing carbon deposits, white
smoke or failure to ignite, or even damaging the glow plug.
Settings cannot be adjusted until the startup process is
complete. After startup, switching between power and
temperature modes or shutting the heater down becomes
possible.
When operating the device for the first time, it is recommended
to pump fuel using manual pump mode, thereby quickly filling
the entire fuel pipeline.
PARKING AIR HEATER
29
In shut-down state, long press the " " + " " keys at the same
time for 2 seconds. The LCD will show "OIL"as
Fig.24, and after
pumping fuel successfully the device will automatically switch into
operating state.
In manual pump mode, long press " " + " " for 2 seconds to exit.
Fig.24 Fig.25
Fig.26 Fig.27
6.3.2 Start-up operation
About 3 seconds after the heater starts up, its glow plug will start
to operate; its fuel pump will start operating after about 1.5
minutes. After successful ignition, the heater will start to operate
normally after about 5 minutes.
In shut-down state, press the " " key to start the device, which
will display its start-up status as
Fig.25.
6.3.3 Shut down operation
After pressing the " " key, the fuel pump will stop immediately,
but the fan will remain running to cool down the heat exchanger
case for 3-5 minutes, displaying "OFF", as
Fig.26.
It will then display "U-12V" as
Fig.27. which means that the
heater has shut down completely.