LED Lighting System Owner’s Manual
Dear Customer, Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. User Memo: Date of purchase: Dealer name: Dealer address: Dealer website: Dealer email: Dealer phone no.: Please visit us on facebook or twitter! https://www.facebook.com/Maxspect http://twitter.
Package Content Please check the content in the package.
Precautions Before using this Maxspect™ R420R LED Lighting System please read these operating instructions carefully. Take special care to follow the safety suggestions listed below. Afterwards keep this manual handy for future reference. Before using the Maxspect™ R420R LED Lighting System 1. 2. Remove any plastic bags and packaging material protecting the fixture. Never look directly at the LED bulbs when you switch on the system. Incorrect use of this apparatus will increase eye hazard. On Safety 1.
Installation Mounting the R420R LED Lighting System Before connecting the LED Modules to Power Supply, first mount the system by using the provided Stand. 1. Assemble the Stand. Assemble the stand by inserting the rails into the two holes located to the side of the R420R LED Module, as illustrated in the following diagram. 2. Tighten the Thumb Screws. Tighten the thumb screws to secure the position of the stand.
Installation 3. Mounting the LED Module on your Aquarium.
Installation 4. Pendant Mounting You can also suspension mount the R420R unit, as illustrated in the following diagram: 5.
Installation 7
Operating Instructions Basic Operations Follow the instructions below to operate and program the R420R LED Module. Note The LED Module turns on automatically when power is connected, and turns off when power is cut. When power is resumed, the LED Module will restore to the previous saved setting automatically, whether it was last set at Manual, Preset or Automatic Mode, and the intensity level of all the LED channels. Switching between Manual, Preset and Automatic Mode 1.
Operating Instructions Manual Mode “M” Under Manual mode, user can adjust the brightness of the two channels by using the control dial. 1. Press the control dial once to enter setup. Channel A will be selected by default. M A: 100% B: 100% LED: ON 2. Rotate the dial to adjust its brightness. (e.g. 100% 60%) M A: 60% B: 100% LED: ON 3. Press the control dial again to switch to Channel B.
Operating Instructions 4. Rotate the dial to adjust its brightness. (e.g. 100% 85%) M A: 60% B: 85% LED: ON 5. Press the control dial again to switch to ON/OFF toggle. M A: 60% B: 85% LED: ON 6. Rotate the control dial to turn the fixture ON or OFF. M A: 60% B: 85% LED: OFF 7. Press the control dial one more time to exit.
Operating Instructions Preset Mode “P” Under Preset mode, the fixture will be running the following predefined photo-period profiles. Under Preset mode, the LCD panel will display the current time and time-point. (e.g. the following diagram illustrates the current time lies between time-point 3 and 4.) P 1 A: 100% 2 3 4 B: 5 6 100% 1. Press the control dial once to enter setup. Preset #1 will be selected by default. P Preset1 S Preset2 2. Rotate the dial to select the desired preset profile.
Operating Instructions Automatic Mode “A” Under the Automatic mode, users can program their own photo-period profile using 6 Time-Points. Understanding Time Points There are a total of 6 Time Points. You can program different luminous output intensity at each Time Point to control the photoperiod and brightness of the system.
Operating Instructions Under Automatic mode, similar to the Preset mode, the LCD panel will also display the current time and time-point. (e.g. the following diagram illustrates the current time lies between time-point 3 and 4.) A 1 A: 100% 2 3 4 B: 5 6 100% 1. Press the control dial once to enter setup. A TIME S PROGRAM 2. Rotate the dial to select between which setting you wish to change. (e.g. Time Program) A TIME S PROGRAM 3. Press the control dial again to select the setting.
Operating Instructions Automatic mode – Setting the clock 1. A Once you are in the clock setting mode, the hour digit is selected by default. TIME: S 2. A 06: Rotate the dial to set the hour. (e.g. 06:30 08:30) TIME: S 3. A 08: A S 5. 30 Press the control dial to change to the minute digit. TIME: S 4. 30 08: 30 Rotate the dial to set the minute. (e.g. 08:30 08:45) TIME: 08: 45 When finished, press and hold the control dial for 2 seconds to exit setup.
Operating Instructions Automatic mode – Programming the Photo-Period 1. Once you are in the program setting mode, Time Point 1 is selected by default. A TP: 1 S A: 100% 8:00 B: 100% 2. Rotate the control dial to select the Time Point you want to modify. (e.g. TP1 TP2) A TP: 2 S A: 3. 100% B: 100% Press the control dial to change the time setting for this Time Point. A TP: 2 S A: 4. 9:00 100% 9:00 B: 100% Rotate the control dial to set the time for the first Time Point. (e.g.
Operating Instructions 5. Press the control dial to change to Channel A. A TP: 2 S A: 100% 6. TP: 2 S A: 80% TP: 2 S A: 80% 10:00 B: 100% 10:00 B: 100% Rotate the dial to change the brightness. (e.g. 100% 95%) A TP: 2 S A: 9. 100% Press the control dial to change to Channel B. A 8. B: Rotate the dial to change the brightness. (e.g. 100% 80%) A 7. 10:00 80% 10:00 B: 95% When finished, press and hold the control dial for 2 seconds to exit setup.
Limited Warranty Maxspect Ltd. warrants all Maxspect™ R420R LED Lighting System products against defects in workmanship for a period of 12-months from the date of purchase. If a defect exists during the warranty period, Maxspect Ltd. at its option will either repair (using new or remanufactured parts) or replace (with a new or remanufactured unit) the product at no charge.
Specifications LED Module Dimensions (L x W x H) R420R – 160w 690mm × 265mm x 25mm (27” x 10” x 0.9”) R420R – 120w 520mm × 265mm x 25mm (20.5” x 10” x 0.9”) Power Supply Unit Weight 2 kg (4.4 lb) Model Input Voltage / Current Output Voltage / Current Weight Meanwell NES-200-36 4.5A/115VAC - 2.5A/230VAC 36V 5.9A 2 kg (4.4 lb) Note: For latest specifications on LED layout, types and color spectrum, please visit our website at www.maxspect.com Specifications are subject to change without notice.
Maxspect Limited www.maxspect.com NOTE: Products, packaging, features and specifications are subject to change. All screen images are simulated. © 2009-2012 Maxspect Limited. Reproduction in whole or in part without written permission is prohibited. All rights reserved. Maxspect and R420R are trademarks of Maxspect Limited. Cree and XLamp are trademarks of Cree, Inc. R420R Owner’s Manual Version 1.0.
