User's Manual

9XTend™ OEM RF Module - Product Manual v2.x6x
© 2010 MaxStream, Inc. 70
IC (Industry Canada) Certification
Labeling Requirements
Labeling requirements for Industry Canada are similar to those of the FCC. A clearly visible label
on the outside of the final product enclosure must display the following text:
Contains Model 9XTend Radio, IC: 4214A-9XTEND
The integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B -
Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accepts
FCC test r
eport or CISPR 22 test report for compliance with ICES-003.
C-TICK (Australia) Certification
Power Requirements
Regulations in Australia stipulate a maximum of 30 dBm EIRP (Effective Isotropic Radiated Power).
The EIRP equals the sum (in dBm) of power output, antenna gain and cable loss and cannot not
exceed 30 dBm.
Figure A-02. EIRP Formula for Australia
NOTE: The maximum EIRP for the FCC (United States) and IC (Canada) is 36 dBm.
Yagi antennas (approved when operating at 100 mW power output or lower)
Part Number Type Connector Gain Application
eliboM / dexiFiBd 1.6NPRigaY tnemelE 26Y-90A
eliboM / dexiFiBd 1.7NPRigaY tnemelE 37Y-90A
eliboM / dex
iFiBd 1.8NPRigaY tnemelE 48Y-90A
eliboM / dexiFiBd 1.9NPRigaY tnemelE 49Y-90A
eliboM / dexiFiBd 1.01NPR
igaY tnemelE 501Y-90A
eliboM / dexiFiBd 1.11NPRigaY tnemelE 611Y-90A
eliboM / dexiFiBd 1.21NPRigaY tnem
elE 721Y-90A
eliboM / dexiFiBd 1.31NPRigaY tnemelE 931Y-90A
eliboM / dexiFiBd 1.41NPRigaY tnemelE
0141Y
-90A
eliboM / dexiFiBd 1.41NPRigaY tnemelE 2141Y-90A
eliboM / dexiFiBd 1.51NPRigaY tnemelE 3151Y-90A
eli
boM / dexiFiBd 1.51NPRigaY tnemelE 5151Y-90A
eliboM / dexiFiBd 1.6CNTPRigaY tnemelE 2MT6Y-90A
eliboM /
dexiFiBd 1.7CNTPRigaY tnemelE 3MT7Y-90A
eliboM / dexiFiBd 1.8CNTPRigaY tnemelE 4MT8Y-90A
eliboM / dexiF
iBd 1.9CNTPRigaY tnemelE 4MT9Y-90A
eliboM / dexiFiBd 1.01CNTPRigaY tnemelE 5MT01Y-90A
eliboM
/ dexiFiBd
1.11CNTPRigaY tnemelE 6MT11Y-90A
eliboM / dexiFiBd 1.21CNTPRigaY tnemelE 7MT21Y-90A
eliboM / dexiFiBd
1.31CNTPRigaY tnemelE 9MT31Y-90A
eliboM / dexiFiBd 1.41CNTPRigaY tnemelE 01MT41Y-90A
eliboM / dexiFiBd
1.41CNTPRigaY tnemelE 21MT41Y-90A
eliboM / dexiFiBd 1.51CNTPRigaY tnemelE 31MT51Y-90A
eliboM / dexiFiBd
1.51CNTPRigaY tnemelE 51MT51Y-90A
Models with ware comply with requirements to be used in end products in Australia. All products with EMC
and radio communications must have a registered C-Tick mark. Registration to use the compliance mark will only be accepted
from Australian manufacturers or importers, or their agent, in Australia. In order to have a C-Tick mark on an end product, a
company must comply with (a) or (b) below.
(a) have a company presence in Australia
(b) have a company/distributor/agent in Australia that will sponsor the importing of said product
Contact Digi for questions related to locating a contact in Australia.