User Manual
Table Of Contents
- 1. Overview
- 2. RF Module Operation
- 3. XBee ZigBee Networks
- Introduction to ZigBee
- ZigBee Stack Layers
- Networking Concepts
- ZigBee Application Layers: In Depth
- Coordinator Operation
- Router Operation
- End Device Operation
- Channel Scanning
- 4. Transmission, Addressing, and Routing
- 5. Security
- 6. Network Commissioning and Diagnostics
- 7. Managing End Devices
- 8. XBee Analog and Digital IO Lines
- 9. API Operation
- API Frame Specifications
- API UART Exchanges
- Supporting the API
- API Frames
- AT Command
- AT Command - Queue Parameter Value
- ZigBee Transmit Request
- Explicit Addressing ZigBee Command Frame
- Remote AT Command Request
- Create Source Route
- AT Command Response
- Modem Status
- ZigBee Transmit Status
- ZigBee Receive Packet
- ZigBee Explicit Rx Indicator
- ZigBee IO Data Sample Rx Indicator
- XBee Sensor Read Indicator
- Node Identification Indicator
- Remote Command Response
- Over-the-Air Firmware Update Status
- Route Record Indicator
- Many-to-One Route Request Indicator
- Sending ZigBee Device Objects (ZDO) Commands with the API
- Sending ZigBee Cluster Library (ZCL) Commands with the API
- Sending Public Profile Commands with the API
- 10. XBee Command Reference Tables
- 11. Module Support
- Appendix A: Definitions
- Appendix B: Agency Certifications
- Appendix C: Migrating from ZNet 2.5 to XBee ZB
- Appendix D: Additional Information
XBee®/XBee‐PRO®ZBRFModules
©2011DigiInternational,Inc. 116
Node Identification Indicator
Frame Type: 0x95
This frame is received when a module transmits a node identification message to identify itself (when AO=0).
The data portion of this frame is similar to a network discovery response frame (see ND command).
Example: If the commissioning push button is pressed on a remote router device with 64-bit
address 0x0013A200 40522BAA, 16-bit address 0x7D84, and default NI string, the following node
identification indicator would be received.
Frame Fields Offset Example Description
A
P
I
P
a
c
k
e
t
Start Delimiter 00x7E
Length MSB 1 0x00 Number of bytes between the length and the checksum
Frame-specific Data
LSB 2 0x20
Frame Type 30x95
64-bit Source
Address
MSB 4 0x00
64-bit address of sender
50x13
60xA2
70x00
80x40
90x52
10 0x2B
LSB 11 0xAA
16-bit Source
Network Address
MSB 12 0x7D
16-bit address of sender.
LSB 13 0x84
Receive Options 14 0x02
0x01 - Packet Acknowledged
0x02 - Packet was a broadcast packet
Source 16-bit
address
15 0x7D
Set to the 16-bit network address of the remote. Set to
0xFFFE if unknown.
16 0x84
64-bit Network
address
17 0x00
Indicates the 64-bit address of the remote module that
transmitted the node identification frame.
18 0x13
19 0xA2
20 0x00
21 0x40
22 0x52
23 0x2B
24 0xAA
NI String 25 0x20
Node identifier string on the remote device. The NI-String
is terminated with a NULL byte (0x00).
26 0x00
Parent 16-bit
address
27 0xFF
Indicates the 16-bit address of the remote's parent or
0xFFFE if the remote has no parent.
28 0xFE
Device Type 29 0x01
0 = Coordinator
1 = Router
2 = End Device
Source Event 30 0x01
1 = Frame sent by node identification pushbutton event
(see D0 command)
2 = Frame sent after joining event occurred (see JN
command).
3 = Frame sent after power cycle event occurred (see JN
command).
Digi Profile ID
31 0xC1
Set to Digi's application profile ID.
32 0x05
Manufacturer ID
33 0x10
Set to Digi's Manufacturer ID.
34 0x1E
Checksum 35 0x1B 0xFF - the 8 bit sum of bytes from offset 3 to this byte.