User Manual

XBee®/XBee‐PRO®ZBRFModules
©2011DigiInternational,Inc. 152
- Integral PCB Antenna (-0.5 dBi)
XBee-PRO (S2) RF Module
The following antennas are approved for use with the embedded XBee-PRO S2 RF Module:
- Dipole (2.1 dBi, Omni-directional, Articulated RPSMA, Digi part number A24-HABSM)
- Chip Antenna (-1.5 dBi)
- Attached Monopole Whip (1.5 dBi)
- Integral PCB Antenna (-0.5 dBi).
XBee-PRO (S2B) RF Module
The following antennas are approved for use with the embedded XBee-PRO RF S2B Module:
- Dipole (2.1 dBi, Omni-directional, Articulated RPSMA, Digi part number A24-HABSM)
- PCB Embedded Trace Antenna (-0.5dBi)
- Attached Monopole Whip (1.5 dBi).
Canada (IC)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Labeling Requirements
Labeling requirements for Industry Canada are similar to those of the FCC. A clearly visible label on the
outside of the final product enclosure must display the following text:
Contains Model XBee Radio, IC: 4214A-XBEE2
The integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B -
Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accepts FCC
test report or CISPR 22 test report for compliance with ICES-003.
If it contains an XBee-PRO (S2) RF Module, the clearly visible label on the outside of the final product
enclosure must display the following text:
Contains Model XBee PRO Radio, IC: 1846A-XBEEPRO2
If it contains an XBee-PRO (S2B) RF Module, the clearly visible label on the outside of the final product
enclosure must display the following text:
Contains Model XBee PRO S2B Radio, IC: 1846A-PROS2B
The integrator is responsible for its product to comply with IC ICES-003 & FCC Part 15, Sub. B -
Unintentional Radiators. ICES-003 is the same as FCC Part 15 Sub. B and Industry Canada accepts FCC
test report or CISPR 22 test report for compliance with ICES-003.
Transmitters for Detachable Antennas
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in
the table above with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device. The required antenna impedance is
50 ohms.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'exploitation de l'émetteur.