User Manual
Table Of Contents
- 1. Overview
- 2. RF Module Operation
- 3. XBee ZigBee Networks
- Introduction to ZigBee
- ZigBee Stack Layers
- Networking Concepts
- ZigBee Application Layers: In Depth
- Coordinator Operation
- Router Operation
- End Device Operation
- Channel Scanning
- 4. Transmission, Addressing, and Routing
- 5. Security
- 6. Network Commissioning and Diagnostics
- 7. Managing End Devices
- 8. XBee Analog and Digital IO Lines
- 9. API Operation
- API Frame Specifications
- API UART Exchanges
- Supporting the API
- API Frames
- AT Command
- AT Command - Queue Parameter Value
- ZigBee Transmit Request
- Explicit Addressing ZigBee Command Frame
- Remote AT Command Request
- Create Source Route
- AT Command Response
- Modem Status
- ZigBee Transmit Status
- ZigBee Receive Packet
- ZigBee Explicit Rx Indicator
- ZigBee IO Data Sample Rx Indicator
- XBee Sensor Read Indicator
- Node Identification Indicator
- Remote Command Response
- Over-the-Air Firmware Update Status
- Route Record Indicator
- Many-to-One Route Request Indicator
- Sending ZigBee Device Objects (ZDO) Commands with the API
- Sending ZigBee Cluster Library (ZCL) Commands with the API
- Sending Public Profile Commands with the API
- 10. XBee Command Reference Tables
- 11. Module Support
- Appendix A: Definitions
- Appendix B: Agency Certifications
- Appendix C: Migrating from ZNet 2.5 to XBee ZB
- Appendix D: Additional Information
XBee®/XBee‐PRO®ZBRFModules
©2011DigiInternational,Inc. 9
Specifications
SpecificationsoftheXBee®/XBee‐PRO®ZBRFModule
Specification XBee XBee-PRO (S2) XBee-PRO (S2B)
Performance
Indoor/Urban Range up to 133 ft. (40 m)
Up to 300 ft. (90 m), up to 200 ft (60 m)
international variant
Up to 300 ft. (90 m), up to 200 ft (60 m)
international variant
Outdoor RF line-of-sight
Range
up to 400 ft. (120 m)
Up to 2 miles (3200 m), up to 5000 ft
(1500 m) international variant
Up to 2 miles (3200 m), up to 5000 ft (1500
m) international variant
Transmit Power Output
2mW (+3dBm), boost mode enabled
1.25mW (+1dBm), boost mode
disabled
50mW (+17 dBm)
10mW (+10 dBm) for International
variant
63mW (+18 dBm)
10mW (+10 dBm) for International variant
RF Data Rate 250,000 bps 250,000 bps 250,000 bps
Data Throughput up to 35000 bps (see chapter 4) up to 35000 bps (see chapter 4) up to 35000 bps (see chapter 4)
Serial Interface Data Rate
(software selectable)
1200 bps - 1 Mbps
(non-standard baud rates also
supported)
1200 bps - 1 Mbps
(non-standard baud rates also
supported)
1200 bps - 1 Mbps
(non-standard baud rates also supported)
Receiver Sensitivity
-96 dBm, boost mode enabled
-95 dBm, boost mode disabled
-102 dBm -102 dBm
Power Requirements
Supply Voltage 2.1 - 3.6 V 3.0 - 3.4 V 2.7 - 3.6 V
Operating Current
(Transmit, max output
power)
40mA (@ 3.3 V, boost mode
enabled)
35mA (@ 3.3 V, boost mode
disabled)
295mA (@3.3 V)
170mA (@3.3 V) international variant
205mA, up to 220 mA with programmable
variant (@3.3 V)
117mA, up to 132 mA with programmable
variant (@3.3 V), International variant
Operating Current
(Receive))
40mA (@ 3.3 V, boost mode
enabled)
38mA (@ 3.3 V, boost mode
disabled)
45 mA (@3.3 V)
47 mA, up to 62 mA with programmable
variant (@3.3 V)
Idle Current (Receiver off) 15mA 15mA 15mA
Power-down Current
< 1 uA @ 25
o
C3.5 A typical @ 25
o
C3.5 A typical @ 25
o
C
General
Operating Frequency
Band
ISM 2.4 GHz ISM 2.4 GHz ISM 2.4 GHz
Dimensions 0.960” x 1.087” (2.438cm x 2.761cm) 0.960 x 1.297 (2.438cm x 3.294cm) 0.960 x 1.297 (2.438cm x 3.294cm)
Operating Temperature -40 to 85º C (industrial) -40 to 85º C (industrial) -40 to 85º C (industrial)
Antenna Options
Integrated Whip, Embedded PCB
Antenna, RPSMA, or U.FL Connector
Integrated Whip Antenna, Embedded
PCB Antenna, RPSMA or U.FL
Connector
Integrated Whip Antenna, Embedded PCB
Antenna, RPSMA or U.FL Connector
Networking & Security
Supported Network
Topologies
Point-to-point, Point-to-multipoint,
Peer-to-peer, and Mesh
Point-to-point, Point-to-multipoint, Peer-
to-peer, and Mesh
Point-to-point, Point-to-multipoint, Peer-to-
peer, and Mesh
Number of Channels 16 Direct Sequence Channels 14 Direct Sequence Channels 15 Direct Sequence Channels
Channels 11 to 26 11 to 24 11 to 25
Addressing Options
PAN ID and Addresses, Cluster IDs
and Endpoints (optional)
PAN ID and Addresses, Cluster IDs and
Endpoints (optional)
PAN ID and Addresses, Cluster IDs and
Endpoints (optional)
Agency Approvals
United States (FCC Part
15.247)
FCC ID: OUR-XBEE2 FCC ID: MCQ-XBEEPRO2 FCC ID: MCQ-PROS2B
Industry Canada (IC) IC: 4214A-XBEE2 IC: 1846A-XBEEPRO2 IC: 1846A-PROS2B
Europe (CE) ETSI ETSI (International variant) ETSI (10 mW max)










