High Performance V.34/V.42bis 28,800 BPS Internal Plug and Play FAX/Voice/Data Modem Featuring Advanced FullDuplex Speakerphone Functions User's Manual Part #MAN080 Rev. 1.
Contents Section One - Introduction ................................. 1 Section Two - Installation .................................. 1 Section Three - AT Command Set .................... 7 Section Four - S Registers .............................. 13 Section Five - Result Codes ............................ 15 Section Six - Troubleshooting .......................... 15 Section Seven - Support and Service .............. 17 Appendix A - Specifications ............................
Section One - Introduction This 28.8 Kbps Plug and Play FAX/Voice/Data Speakerphone Modem connects your computer to all popular high speed modems available today. Your new modem features advanced speakerphone functions for hands-free voice communication and is compatible with Plug and Play (PnP) systems for simplified installation and configuration. This manual describes the hardware installation procedures for your new modem product.
or, 2. If running DOS or Windows 3.x, configure the modem using the included modem driver. Instructions for installing this driver are included in the text file called README.1ST on the Windows 95 driver disk. The README.1ST file can be viewed by loading it into any wordprocessor or any text editor (i.e. DOS EDIT, NOTEPAD). It may also be viewed by using the DOS TYPE command. Refer to your word processor manual or DOS/Windows references for information on loading text files. 2.
6. Replace the computer cover and plug in your computer. 7. Connect the telephone cable from the modem's LINE connector to the telephone wall jack. See Figure 2-2. 8. Optionally, connect your telephone to the modem's PHONE connector. 9. Optionally, connect your microphone to the modem's MIC jack. 10. Optionally, connect your speakers into the modem's SPK jack. 11. Turn your computer on. Your modem is now installed. 2.
The Install From Disk dialog box now instructs you to “Insert the manufacturer's installation disk into the drive selected, and then click OK.” Insert the modem's Utility diskette into the disk drive and type A:\ (or B:\ if inserted in drive B) in the “Copy manufacturer's files from:” box. Click “OK.” Windows 95 may request its own installation disks for some files. Insert the Windows 95 disks as required. When all necessary files are copied, the modem is configured.
MANAGER|MAIN|CONTROL PANEL, click on PORTS and follow Windows 3.1x user's manual instructions on configuring the installed modem COM port. Proceed to Section 2.5, Software Installation/Configuration. 2.5 Software Installation and Configuration You are now ready to install and configure the communication software. Refer to your software manual for installation procedures. We suggest the following communication parameters when you first use your data communication software.
2.7 Testing Your Modem After Installation In order to test your modem you should be familiar with your communication software. Load and set up your communication software and enter into “terminal mode.” Make sure that the COM Port and IRQ settings of the modem match the software. Type AT on your terminal screen and press ENTER. You may see “AT”, “AATT” or nothing on the screen. In any case, the modem should respond with an OK or 0.
Section Three - AT Command Set 3.1 Executing Commands Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands may be sent to your modem from a PC running communication software or any other terminal devices. Your modem is capable of data communication at rates of: 300, 1200, 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, and 115200 bps.
, @ ! ; DS=n E_ pause wait for five seconds of silence flash return to Command Mode after dialing Dial one of the four telephone numbers (n=0-3) stored in the modem’s non-volatile memory.
W_ W0 W1 W2 X_ X0 X1 X2 X3 X4 Y_ Y0 Y1 Z_ Z0 Z1 Report DTE speed only Report line speed, error correction protocol, and DTE speed. Report DCE speed only Hayes Smartmodem 300 compatible responses/blind dialing.
&P2 &P3 ratio Same as &P0 setting but at 20 pulses per minute Same as &P1 setting but at 20 pulses per minute &R_ &R0 &R1 Reserved CTS operates per flow control requirements &S_ &S0 &S1 Force DSR Signal High (ON) DSR off in command mode, on in on-line mode &T_ &T0 &T1 &T3 &T4 Ends test in progress Perform Local Analog Loopback Test Perform Local Digital Loopback Test Grant Remote Digital Loopback Test request by remote modem Deny Remote Digital Loopback Test request Perform a Remote Digital Loopba
d=300-28800. A, b, c, d default=11, 1, 300, 28800. Parameter “a” specifies the modulation protocol desired where: 0=V.21, 1=V.22, 2=V.22bis, 3=V.23, 9=V.32, 10=V.32bis, 11=V.34, 64=Bell 103, 69=Bell 212, and 74=VFC. Parameter “b” specifies automode operations where: 0=automode disabled, 1= automode enabled with V.8/V.32 Annex A. Parameter “c” specifies the minimum connection data rate (300-28800). Parameter “d” specifies the maximum connection rate (300-28800).
\N2 \N3 \N4 \N5 V.42 or MNP data link only V.42/MNP/Normal data link V.42 data link only MNP data link only 3.6 Fax Class 1 Commands +FAE=n +FCLASS=n +FRH=n +FRM=n +FRS=n +FTH=n +FTM=n +FTS=n Data/Fax Auto Answer Service Class Receive data with HDLC framing Receive data Receive silence Transmit data with HDLC framing Transmit data Stop transmission and wait 3.
+FPTS: +FPTS= +FREV? +FSPL +FTSI: Page Transfer Status Page Transfer Status Identify Revision Enable polling Report the Transmit Station ID 3.
Table 4-1 S - Registers Register Function Range/units S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 S10 S11 S12 S13 S14 Default Auto-answer Ring 0-255 /rings 0 Ring counter 0-255 /rings 0 Escape code character 0-127 /ASCII 43 Carriage return character 0-127 /ASCII 13 Line feed character 0-127 /ASCII 10 Backspace character 0-32, 127 /ASCII 8 Dial tone wait time 2-255 /seconds 2 Remote carrier wait time 1-255 /seconds 50 Comma pause time 0-255 /seconds 2 Carrier detect response time 1-255 /0.
S49-81 Reserved S82 Break options 3, 7, or 128 S83-85 Reserved S86 Connection failure code 0, 4, 5, 9, 12, 13, 14 S87-S90Reserved S91 Transmit attenuation 0-15/dBm S92 Fax attenuation 0-15/dBm S95 Extended result code optionsBit-mapped register 128 * 10 10 Section Five - Result Codes OK 0 RING 2 ERROR 4 NO DIALTONE 6 NO ANSWER 8 CONNECT 2400 10 CONNECT 9600 12 CONNECT 12000 14 CONNECT 19200 16 CONNECT 57600 18 CONNECT 1200TX/75RX 22 FAX 33 CARRIER 300 40 CARRIER 75/1200 45 CARRIER 2400 47 CARRIER 7200 49
receive data from the modem. 2. Make sure that your modem is initialized correctly. Your modem may have been initialized to not display responses. You may factory-reset the modem by issuing AT&F and press ENTER. The factory default allows the modem to display responses after a command has been executed. Modem does not dial. 1. Make sure the modem is connected to a working phone line. Replace the modem with a working phone to ensure that the phone line is working. 2.
communication software. 3. Make sure the data speed is not faster than your computer's capability. Most IBM compatibles are capable of 19,200 bps under DOS and Windows. Operating at higher speeds under Windows requires a faster CPU (386/486 or better), a high performance replacement Windows 3.1x comm.drv, or Windows 95. Modem experiences bursts of errors or suddenly disconnects while communicating with a remote modem. 1. Make sure Call Waiting is turned off. 2.
Data format: Power: Temperature: Caller ID: PnP: Speakerphone: 300-115200 bps 0.75 W 0 to 55 degrees C (Operating) Yes Revision 1.0a Full-duplex with DSP echo cancellation Appendix B - Speaker Type Selection Your modem supports both mono and stereo speakers. Use jumper JP3 to select the speaker type. The modem is factory set to use stereo speakers (jumper over both pins). If you use a mono speaker, remove the jumper (See Figure B-1).
The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). FCC Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
21
