XT5861 15 INCH COLOR MONITOR USER'S MANUAL Features: • 1280 x 1024, Non-Interlaced • .28 mm Dot Pitch • 72 Hz Refresh Rate (VGA/SVGA) • Power Saving Operation (VESA DPMS) • Non-Glare Screen • Full Screen Display • Easy Access Front Controls • Unlimited Palette of Colors • Plug and Play Part #MAN099 Rev 1.
Table of Contents Section 1 - General Information ............................................................ Section 2 - Installation ........................................................................... Section 3 - Monitor Controls and LEDs ................................................. Section 4 - Troubleshooting ................................................................... Appendix A - Specifications ...................................................................
Section 1 - General Information Congratulations on purchasing the 15 inch Color Monitor. The monitor uses one of the finest CRTs available in the industry. The .28 mm dot pitch non-glare tube and a crisp, vivid color display with a 80 MHz video bandwidth, make it the perfect monitor for applications ranging from CAD/ CAM or business presentations to desktop publishing. The monitor is capable of video resolutions including VGA, Super VGA, and XGA.
signal is re-enabled the monitor returns to normal operation. The monitor enters DPMS OFF mode when the computer turns off both the Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 3W. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top.
• Plug the 15-pin male connector on the video cable into the output connector on the rear of your computer system. The video output connector on your computer may be either in a location similar to Figure 2-2 or on an expansion board. Secure the cable to the computer using the thumbscrews on the 15-pin connector. • Attach the power cord to the monitor and plug it into an AC outlet. • The monitor is now ready for use.
. Vertical-Size: Adjusts the display height 7. Horizontal-Position: Adjusts the horizontal position 8. Horizontal-Size: Adjusts the display width. 9. Brightness Control: Adjusts the display brightness. Turn clockwise to increase the brightness. 10. Contrast Control: Adjusts the contrast. Turn clockwise to increase the contrast. Section 4 - Troubleshooting No picture, power indicators A, and B off • Check AC cord is plugged into outlet and monitor. • Turn on the power switch.
SVGA SVGA 8514A(Interlaced) Ultra VGA Ultra VGA Ultra VGA 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1280 x 1024 60 Hz 72 Hz 87 Hz 60 Hz 70 Hz 60 Hz 38.00KHz 48.08 KHz 35.52 KHz 48.36 KHz 56.48 KHz 64.00 KHz Input voltage 110~240VAC, 50/60 Hz Front controls Power, Brightness, Contrast, Horizontal-Size, Horizontal-Position, Vertical-Size, Vertical-Position, Pincushion, Trapezoid Power saving Display Power Management Signaling (DPMS) STAND-BY mode 15W (Max.) OFF mode 3W (Max.
Appendix C - Three Year Warranty MAXTECH warrants to the original buyer of this product against defects in material and workmanship for three years from the date of purchase. Except as specified below, this warranty covers all defects in material or workmanship in this product. The following are not covered by the warranty: 1. Any product which is not distributed in North America by MAXTECH or which is not purchased in North America from an authorized MAXTECH Dealer. 2.
address provided by the technician when you call. We recommend that the unit be insured. This warranty is valid for products sold in North America only. Contact your local authorized distributor or dealer for the warranty offered in other areas. All warranty services must be performed by Authorized Service Centers. There are no user serviceable parts inside the unit. Do not remove any components or attempt to service the unit by any unauthorized service center.
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase the separation between the equipment and the receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio / TV technician for help Notice: Shielded cables, if an
