XT7800 17 INCH COLOR MONITOR USER'S MANUAL Features • • • • • • • • • 0.28 mm Dot Pitch 1280 x 1024, Non-Interlaced 90 Hz Refresh Rate (VGA/SVGA) Power Saving Operation (VESA DPMS) Non-Glare Screen Full Screen Display Digital Controls RGB Color Match Controls Low Radiation Part #MAN061 Rev. 1.
Table of Contents Section 1 Section 2 Section 3 Section 4 Appendix A Appendix B Appendix C Appendix D General Information ......................................................... 2 Installation ........................................................................ 3 Monitor Controls and LEDs ............................................. 4 Troubleshooting ............................................................... 6 Specifications ...................................................................
Section 1 - General Information Congratulations on purchasing the MaxTech 17-inch Color Monitor. The monitor has one of the finest CRTs available in the industry, providing a full range of video display resolutions and complies with the MPR-II standard to reduce electromagnetic emissions. The monitor has a 0.28 mm dot pitch display with a 75 MHz video bandwidth. It supports video resolutions ranging from 640 x 350 to 1280 x 1024 (non-interlaced).
Horizontal and Vertical Synchronization signals. This mode reduces the monitor’s power consumption to 5W. While in this mode the first and second LEDs in the Power Indicator (LEDs A and B in Figure 3-1) are off. When the synchronization signals are re-enabled the monitor returns to normal operation. Section 2 - Installation 2.1 Attaching the Base Figure 2-1 Connecting the Base • Carefully place the monitor on its side or top.
on the computer. • Connect the supplied power cord into the AC connector on the back of the monitor and the other end into an AC outlet. • The monitor is now ready for use. Section 3 - Monitor Controls and LEDs Figure 3-1 Controls and LEDs A B C 1 12 (on back) 11 1. 10 9 8 7 6 5 4 3 2 Power Indicator LEDs A, B, and C (See Figure 3-1) indicate the operational state of the monitor. 1.1 LEDs A, B and C are lit: The monitor is in normal operating mode. 1.
5. Contrast Control Adjusts the display contrast. 6. Memory Recall Push to reset the display to the default parameters. 7-10 On-Screen Display Controls The On-Screen Display (Refer to Section 3.1) is controlled using buttons 7 through 10. The On-Screen Display is enabled by pressing any of these buttons. 7. ADJ+ Pressing this button will increase the value of the highlighted setting. 8. ADJPressing this button will decrease the value of the highlighted setting. 9.
C. Horizontal-Position Adjusts the horizontal position. The ADJ+ button moves the display to the right. The ADJ- button moves the display to the left. D. Vertical-Position Adjusts the vertical position. The ADJ+ button moves the display up. The ADJ- button moves the display down. E. Pincushion Adjusts the shape of the left and right sides of the display. The ADJ+ button makes the display sides curve out. The ADJ- button makes the display sides curve in. F.
Data Area 12.75 x 9.625 in. Preset Display Modes Mode VGA VGA VGA SVGA 8514A VGA VGA VGA SVGA SVGA SVGA Ultra VGA Ultra VGA Ultra VGA Synchronization Resolution 640 x 350 640 x 400 640 x 480 800 x 600 1024 x 768 640 x 350 640 x 400 640 x 480 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1280 x 1024 V. Frequency 70 Hz 70 Hz 60 Hz 56 Hz 87 Hz 84 Hz 84 Hz 84 Hz 72 Hz 60 Hz 72 Hz 60 Hz 70 Hz 60 Hz Horizontal: Vertical: H. Frequency 31.47 KHz 31.47 KHz 31.47 KHz 35.16 KHz 35.52 KHz 37.86 KHz 37.
2. Any product on which the serial number has been defaced, modified or removed. 3. Damage, deterioration or malfunction resulting from: a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature, commercial or industrial use, unauthorized product modification, or failure to follow instructions supplied with the product. b. Repair or attempted repair by anyone not authorized by MaxTech. c. Any shipment of the product (claims must be presented to the carrier). d.
particular installation.