Network (JPEG2000+H.264) User’s Manual Ver1.
Network (JPEG2000+H.264) Installation & Safeguards Network Stand Alone DVR INSTALLATION & SAFEGUARDS All the safety and operating instructions should be read before the unit is operated. Environment Condition for Installation To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust. This unit should be located in an area with low humidity and a minimum of dust.. Place this unit in a well-ventilated place and do not place heat-generating objects on this unit.
Network (JPEG2000+H.264) Contents Network Stand Alone DVR Contents CHAP. 1 1-1. 1-2. CHAP. 2 2-1. 2-2. CHAP. 3 3-1. 3-2. 1) 2) 3) 4) 5) 6) 7) CHAP. 4 4-1. 4-2. 4-3. 4-4. 1) 2) 3) 4) 5) 4-5. 4-6. 4-7. 4-8. 4-9. 4-10. 4-11. CHAP. 5 5-1. 5-2. 1) 2) 5-3.
Network (JPEG2000+H.264) Contents Network Stand Alone DVR 6) 7) 8) 9) 5-4. 1) 2) 3) 5-5. 5-6. 1) 2) 3) 4) 5) 6) 7) 5-7. 5-8. CHAP. 6 6-1. CHAP. 7 7-1. 7-2. 7-3. 7-4. 7-5. 7-6. 7-7. 7-8. CHAP. 8 8-1. 8-2. 8-3. CHAP. 9 1) 2) CHAP.10 CHAP.
Network (JPEG2000+H.264) CHAP. 1 Features & Package Contents Network Stand Alone DVR CHAP. 1 Features & Package Contents 1-1.
Network (JPEG2000+H.264) CHAP. 1 Features & Package Contents Network Stand Alone DVR 1-2. Package Contents CAMERA SETUP 1/ON 2/OFF 3/OPEN 4/CLOSE 5/NEAR 6/FAR 7/WIDE 8/TELE MENU NEXT J .SHUTTLE RUN HDDFULL RECORD 9/SET PLAY 10/CLEAR 11/GOTO ACTI V E 12/AUTO ETHERNET USB 13/F1 14/F2 15/F3 16/F4 PTZ ZOOM FRZ K. LOCK REC STOP PLAY SEARCH MODE PI P SEQ Q.PLAY IR 2. Remote Controller 1. DVR Main Unit 3. Power Cable 7. Rubber Pad 4. Power Adapter 8. HDD absorber 5.
Network (JPEG2000+H.264) CHAP. 2 Function of Each Button Network Stand Alone DVR CHAP. 2 Function of Each Button 2-1 FRONT Name Function ① LED Lamps Shows status of operation ②-1 USB HOST Back-Up by connecting USB Media to USB HOST ②-2 USB Device Firmware upgrade by connecting PC with latest firmware to USB port ③ IR IR receiver ④ Camera selection & PTZ camera control 1. Pressing this button will display a full screen image of that camera ⑤ Record / Playback 2.
Network (JPEG2000+H.264) CHAP. 2 Function of Each Button Network Stand Alone DVR Name ⑦ LIVE View Control Function PTZ ZOOM Zooming an image FRZ Freezing an image MODE Switch to split display MODE button changes screen-division from (to) full screen to (from) 16-split screen. PIP Display in PIP (Picture in Picture) mode SEQ Auto camera image sequencing in full screen mode K.LOCK Q.
Network (JPEG2000+H.264) CHAP. 2 Function of Each Button Network Stand Alone DVR 2-2. REAR Name 1 Function RS 485 Connection with PTZ Camera or other external device using RS 485 interface RELAY Output Relay out terminal SENSOR Input Sensor input terminal 2 VGA Connection to VGA Monitor (CRT type or TFT LCD monitor) Just in case you purchased DVR with VGA option board fixed on the main board of DVR, you can connect VGA Monitor to DVR unit.
Network (JPEG2000+H.264) CHAP. 3 Installation Network Stand Alone DVR CHAP.3 Installation 3-1.
Network (JPEG2000+H.264) CHAP. 3 Installation Network Stand Alone DVR 3-2. Detailed Installation 1) Rack mount 1. Remove 4 bolts on each side cap to install rack mount. 2. Attach rack mount bracket to DVR. 3. Attach DVR with rack mount bracket to 19” rack. 2) HDD HDD fix Connection of HDD Cable I/O BOARD I/O BOARD MAIN BOARD MAIN BOARD Screw hole HDD1 (MASTER1) HDD2 (MASTER2) CD Recorder (MASTER) x x x x x x x x x x x x 1.
Network (JPEG2000+H.264) CHAP. 3 Installation Network Stand Alone DVR 3) Camera Connect cameras to the camera input on rear panel of DVR marked CAMERA IN. 4) Monitor VIDEO A IN OUT VIDEO B IN OUT VIDEO C IN OUT Connect the video output marked MONITOR to Video-In of Main monitor. 5) Power Connect one DC 12V, 6.67 A Adaptor to the back side of Power Jack for right operation of 2HDDs and CD Recorder.
Network (JPEG2000+H.264) CHAP. 3 Installation Network Stand Alone DVR 6) SPOT, VIDEO PRINTER Connection with additional composite monitor 7) Other External Device RS-232C : Control DVR through RS-232C port by using PC. RS-485 : Control external device like PTZ Camera RELAY Output : Relay Output – Pin No.4 ~ No.6 at Terminal Block SENSOR Input : SENSOR Input (Alarm connection) – Pin No.7 ~ No.26 at Terminal Block ETHERNET : Connection to LAN, WAN, Internet.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR CHAP. 4 Operation 4-1. System Log-In 1) To enter into the setup menu, press the [MENU] button. DVR LOG-IN 2) Enter password with channel number button from No.1 to No.10 on the front of the DVR unit. (Maximum of 8 digits are available) ENTER PASSWORD : _ _ _ _ _ _ _ _ 3) After inputting the password, press the [ENTER] button.
Network (JPEG2000+H.264) CHAP 4. Operation Network Stand Alone DVR 4-3.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 2) View in Sequence Press [SEQ] button. It automatically displays full screen images in sequence. CH16 …… CH02 ● ● ● CH01 3) Picture in Picture(PIP View) When it is in full screen display mode, you can see other camera in a small window by pressing [PIP].
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 4-5. Record Recording mode set before delivery by manufacturer (Default recording mode) is Schedule Recording. In this default recording mode, it records 24 hours/day continuously in weekday and on the weekend. Once you press the [REC] button while you see live view, the record type is changed to Emergency Record mode.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 4-7. Search Press [SEARCH] button, and 3 different methods for searching recorded data are available as shown in following SEARCH window. For selecting searching method, use direction key or Jog/Shuttle. After selecting each search method, press [ENTER] button for playback. exit, press [MENU] button. 1) SEARCH BAR Search by percentage of total recorded data. It starts from image corresponding to set % of data on the search bar.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR Button PTZ command Button PTZ command 1/ON LIGHT ON 10/CLEAR PRESET CLEAR 2/OFF LIGHT OFF 11/GOTO PRESET GOTO 3/OPEN IRIS OPEN 12/AUTO AUTO SCAN 4/CLOSE IRIS CLOSE 13/F1 ~ 16/F4 FUNCTION 5/NEAR FOCUS NEAR UP BUTTON TILT UP 6/FAR FOCUS FAR DOWN BUTTON TILT DOWN 7/WIDE ZOOM IN LEFT BUTTON PAN LEFT 8/TELE ZOOM OUT RIGHT BUTTON PAN RIGHT 9/SET PRESET SET 4-9.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 4-10. Audio Operation Press [AUDIO] button to select audio channel..Ch1, Ch2, Ch3, Ch4 or silence in due sequence. ※Sound of the selected audio channel comes out in Live display. Recorded sound comes out in Playback. 4-11. Mouse Operation 1) Basic Operation There are 11 keys that work by Mouse. LEFT, RIGHT, WHEEL button Click once, double Click, Click longer. And WHEEL UP/DOWN.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 4) Working Status in LIVE MOUSE ICON To work command in ICON, user click Left button once. In case ICON is divided, upper part of button : Mouse Left button click once Lower part of button : Mouse Right button click once Following is the assigned KEY by each ICON.
Network (JPEG2000+H.264) CHAP. 4 Operation Network Stand Alone DVR 6) Working Status in PTZ MOUSE ICON Mouse working is the same as LIVE ICON. Place Mouse at GOTO PRESET, and by Wheel Up/Down, User can change value PRESET,TOUR, GOTO and etc. For other ICONs, user can change channel by Wheel Up/Down. Following is the assigned KEY by each ICON.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR CHAP. 5 Set Up 5-1. Entering into the Menu Enter into SYSTEM MENU by pressing [MENU] button.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 5-2. DISPLAY SETUP Setting up parameters for monitor and display on screen. Enter into SYSTEM MENU-DIPLAY SETUP. DISPLAY SETUP LIVE PLAYBACK SCREEN DISPLAY MONITOR SETUP VGA SETUP COLOR BAR TEST SELECT MENU : ▲▼, & [ENTER] 1) SCREEN DISPLAY 1 2 Setting up the screen display in LIVE mode and PLAYBACK mode. 3 4 Select the sub-menu which you would like to set using direction buttons and then change ON/OFF with [ENTER] button. 1.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 5-3. CONFIGURATION Various parameters for system can be set in CONFIGURATION menu. Enter into SYSTEM MENU-CONFIGURATION and press the [ENTER] button.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR (3) HDD CHANGE SETUP HDD CHANGE SETUP SAVE DVR INFO LOAD DVR INFO SELECT MENU : ▲▼, & [ENTER] 1) SAVE DVR INFO Once you press ENTER button on "SAVE DVR INFO" , the DVR information will be saved on HDD. If the DVR information is saved properly, you can see "NOW CHANGE HDDDISK" message on DVR. Then power off the DVR and change with new HDD.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 2) TIME/DATE SETUP Set time and date of DVR system which is very important for search with time and date of the event. Time and date set by manufacturer is different from local time of user, and user must set time and date exactly in the first operation. Set time & date using direction buttons and [-][+] button or Jog shuttle 2.
Network (JPEG2000+H.264) CHAP.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR INTERVAL SETUP 4) INTERVAL SETUP SWICHING INTERVAL Set the switching time interval for SEQ or PIP function.(1 sec. ~ 99 sec.) (1)FULL SCREEN : set the sequencing switch time interval in live full screen. FULL SCREEN : 01 SEC PIP SCREEN : 01 SEC EVENT RECORD EVENT UPDATE TIME : 01 SEC (2)PIP SCREEN : set the sequencing switch time interval of PIP window.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 7) BUZZER SETUP BUZZER SETUP Set parameters for buzzer (On or Off). Use direction button and [ENTER] button. KEY BEEP : buzz when button is pressed. VIDEO LOSS : buzz when video signal is lost. ALARM ACTIVE : buzz when alarm is activated. MOTION DETECT : buzz when motion is detected. ALL ON KEY BEEP ON VIDEO LOSS ON ALARM ACTIVE ON MOTION DETECT ON User can set all buzzers at On/Off at once by set ALL at ON/OFF.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 5-4. RECORD SETUP This is the most important configuration of the DVR. Enter into SYSTEM MENU-RECORD SETUP and press the [ENTER] button. 1) RECORD CONFIGURATION Use direction button to move and [-] [+] button to set value. RECORD SETUP RECORD CONFIGURATION SCHEDULE SETUP HOLIDAY SETUP (1) OVERWRITE : Set overwrite or stop recording when the HDD is full.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 2) SCHEDULE SETUP Unless you selected other recording mode, DVR system records in Schedule Recording mode. In SCHEDULE REC SETUP, you set type of recording for every time interval of 2 hours in each day of the week. Schedule Recording set by manufacturer is recording continuously at its full recording speed, and it means DVR system record continuously at 60 ips in total at 720x240 resolution.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 5-5. BACK-UP 1) CD Recorder SETUP User can back up the recorded data to CD using CD writer installed in DVR. Refer to [START] and [END] of data on HDD and set copy from time, [START], and size of data copied, [SIZE], and move to BURN and press [ENTER] button to start copy.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR USB HDD control only : Partition can be selectable by Ch button 1~4.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR (2) DDNS SETUP : DDNS SETUP DDNS ON/OFF : Select if DDNS Function use. DDNS SERVERS :IP Address of DDNS SERVER. INTERVAL : Registered time period to DDNS SERVER. Per D(Day) H(Hour) M(Minute). In REGISTER, Once press [enter], It automatically registered.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR (5) EVENT SERVER SETUP : IP ADDRESS : IP Address of PC that executes EVENT SERVER PROGRAM. IP PORT : PORT of PC that executes EVENT SERVER PROGRAM EVENT SERVER TYPE : It is the way to transmit data to SERVER By "OFF", "EVENT", "MINUTE“, In case Event happens from DVR. EVENT SERVER SETUP IP ADDRESS IP PORT EVENT SERVER TYPE INTERVAL EVENT GMT TYPE 192.168.001.072 09988 OFF --GMT+00:00 "EVENT“: It transmits by the number of EVENT.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR RS-232C SETUP 2) RS-232C SETUP SPEED User can control the DVR via RS-232C port. Connect DVR to PC via RS-232C port and control DVR using keyboard of PC. This function is mainly for programmer who wants to control DVR as part of many devices connected to PC system, as in SI project. 115200 LENGTH 8 STOP BIT 1 PARITY NONE SELECT : ▲▼, CHANGE VALUE : + - 3) PAN/TILT SETUP It is to set parameters for PTZ camera connected to DVR unit.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR If events (MOTION or ALARM) happen on several channel at the same time, channel No. 1 has the first priority to pop up. For example, if events happen on channel No. 1, channel No. 2, and channel No. 4 at the same time, channel No. 1 pops up. If the motion disappears on channel No. 1, then channel No. 2 pops up for the duration that you set. However, even though motion happens on channel No. 1 again within the duration, channel No.
Network (JPEG2000+H.264) CHAP. 5 Set Up Network Stand Alone DVR 5-7. FACTORY DEFAULT FACTORY DEFAULT ALL SCREEN DISPLAY CAMERA SETTING MOTION SETUP PANTILT SERUP SCHEDULE SETUP CONFIGURATION Set the all system parameters as manufacturer first set before delivery. It is a kind of system initialization, and manufacturer recommends to do it when you add new HDD or other changes in system to make all system ready for normal operation.
Network (JPEG2000+H.264) CHAP. 6 Network Setup Network Stand Alone DVR CHAP. 6 Network Setup 6-1. DVR Network Configuration Please call your provider to identify what type of service they are providing you.
Network (JPEG2000+H.264) CHAP. 6 Network Setup Network Stand Alone DVR 1) Static IP User input IP address in IP CONFIG SETUP which is assigned from ISP company. 1. Verify if IP address is OK or not with PC before connecting DVR. 2. Connect LAN cable to DVR after confirmation. 3. DVR : MENU Æ EXTERNAL DEVICE Æ TCP/IP 4. Set DHCP to MANUAL and go into TCP/IP SETUP. 5. Verify if MAC ADDRESS starts from 00-0A-A2…. 6. Input IP address which is assigned from ISP company. 7. Set IP PORT. (50000 recommended) 8.
Network (JPEG2000+H.264) CHAP. 6 Network Setup Network Stand Alone DVR 2) Dynamic IP 1. Verify if IP address is OK or not with PC before connecting DVR. 2. Connect LAN cable to DVR after confirmation. 3. Turn off and on Modem (Router) which is provided by ISP company. Æ This is to reset client of MAC from ISP company. User have to wait for 30 seconds after turning on. 4. Turn off and on DVR. 5. DVR : MENU Æ EXTERNAL DEVICE Æ TCP/IP 6. Verify if MAC ADDRESS starts from 00-0A-A2…. 7.
Network (JPEG2000+H.264) CHAP. 6 Network Setup Network Stand Alone DVR 3) Dynamic IP of PPPoE (DSL) DVR doesn’t support DSL (PPPoE), user have to set NETWORK with IP SHARE if user need to access DVR remotely. At this time, User have to port forward on DVR. Please contact IP SHARE Manufacturer if you need to know how to forward port. Even though user have Static/Dynamic IP, if user want to use another device (PC) through IP SHARE, user can set NETWORK as follows, 1.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR CHAP 7. IRS(Integrated Remote Station) MAIN INTERFACE Exit IRS SETUP Inputs Information for IRS network connection. DVR SETUP Changes DVR setting over a network. VIEWER Enables to show live image display. BACKUP Enables to back up recorded images in DVR to your PC. PLAYER Enables to back up recorded images on your PC. (AJP file) TRANSMITER Enables to control DVR using virtual key like controlling actual DVR remotely.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-1. IRS SETUP MANUAL DDNS Select “Manual” to input IP address and port number manually. Select “DDNS” to use IP address and port number that you already registered in DDNS Server. MEMBER ID NAME Input member ID that you registered in DDNS Server. Input DVR name that you registered in DDNS Server. ADDRESS PORT Input IP address manually. Input Port number manually. LOGIN ID Password Input DVR ID which has been set in DVR already.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-2. DVR SETUP User can change some settings of DVR listed below over a network. (Active Camera, Alarm, Buzzer, Interval, Password, Record Configuration, Record Schedule) MANUAL Input IP address and port number of DVR manually. ADDRESS Input IP address of DVR manually. PORT NUMBER Input port number of DVR manually. LOGIN ID PASSWORD Input DVR ID which has been set in DVR already. (Input ‘admin’.) Input password of DVR.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-3. VIEWER 1 2 3 4 5 6 1 DVR connection setup : Input network information to connect. (IP / PORT / ID / PW) 2 Network Connection a) CONNECT : Click this button to connect to DVR & see live view over a network. b) DISCONNECT : Click this button to disconnect. 3 System Information : Displays connection status and operating Information. 4 PTZ Control : Command PTZ Camera connected to DVR remotely.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-4. BACKUP 1) To execute BACKUP, input IP Address & Port and click ‘Connect Test’ button. 2) After Connect Test is done, you can see ‘Success Connect Test!’ message. Then,click ‘lock’ button and click ‘Set Backup Time’ button.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 3) Now you set ‘Start Time’, ‘End Time’, ‘Save File Path’, ‘File Size’ and click ‘Apply’. 4) After finishing time setting, click ‘Start Backup’ to start backup. Then, you can see the backup on the path that you chose.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-5. PLAYER 1 2 3 4 a 8 b c d 7 e f g 5 6 1 Time Display : Displays current time. 2 Recorded data display : Displays start time & end time of recorded data. Also, displays operating status during playback. 3 Screen display : Selects full screen mode or split mode and displays full screen for each ch. 4 Audio : Set Audio On/Off. 5 Function buttons a) OPEN : Selects bakuped file.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR Image EDIT 1 2 3 1 1. RECORDED DATA DISPLAY : Displays start time & end time of recorded data. Also, displays operating status during playback. 2 2. EDIT TOOL : User can adjust color tone of copied images using this buttons.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR AVI SAVE 1 2 3 1 RECORDED DATA DISPLAY : Displays start time & end time of recorded data.Also, 1. displays operating status during playback. 2 2. OPTION : Used to save data in AVI file format. - CHANNEL : Selects channel. - FRAMERATE : Decides frames per second of data to be saved. - SIZE : Decides the size of data to be saved automatically. - START : Starts saving. - STOP : Stops saving.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-6. TRANSMITTER 1 2 3 4 5 1 DVR Connection Setting : Inputs information for DVR Network connection . Check ‘IP / PORT / ID / PW’ information. 2 Network Connection a) CONNECT : Network connection to DVR. ( User can see live image of DVR. ) b) DISCONNECT : Network disconnection from DVR. c) SETUP : User can change or set ‘NVS Setup’ of DVR System Menu. 3 System Information : Displays DVR Connection and System Operation Information.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-7. CLIENT MAIN INTERFACE 1 2 3 4 8 1 2 3 4 5 6 7 8 7 5 6 Power button : Press the Power switch to exit the program. Please disconnect the live feed before powering off the software Status window : Display’s the current time and date based. The date is in the format : Year/Month/Day. You will also see the status of your connection. Setting, Playback, and Sequence buttons : a) Setting : Enables the software configuration screen.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR IP/PORT Setting Screen IP List MANUAL DDNS Input IP address and PORT manually Receive IP address and PORT from DDNS Server. For further information of DDNS, please contact your vendor. Name Address PORT ID Password Name of IP address on the list. Input IP address which is set on DVR Input PORT which is set on DVR Input ID which is set on DVR. (Please input ‘admin’.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR PTZ/SAVE Setting Screen Circular Monitoring Interval : This indicates the speed of the channels sequence when the SEQUENCE button is used from the main interface. Scan Rate : Set speed of playback. PTZ TYPE : Select PTZ camera which is connected to DVR. PTZ Baud Rate : Enter the Baud Rate of your PTZ camera. Set Path to Save Downloaded image : Determines the location and folder on your PC where the downloaded video clips are stored.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR 7-7. CMS 1 2 3 4 7 5 6 8 9 10 11 12 13 1 CMS Setting : CMS Setting. (User can set DVR Registration here for multi-access.) 2 Group Setup : Among multi-access DVRs, User can make group at specific chs to live monitor. 3 Search : Playback and search recorded image of one DVR. 4 View Tree : If No11 is not displayed,it will be displayed again. 5 View Event : If No 12 & 13 is not displayed, it will be displayed again.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR DVR Registration and Screen Display 1) To connect DVR,from main screen to proceed ‘CMS Setting > Site setup > ‘Registering Site’, and then, register neccesary information for DVR connection as below, (Registration is the same as ‘IRS SETUP’.
Network (JPEG2000+H.264) CHAP. 7 IRS Network Stand Alone DVR DVR Group Setup 1) After finishing DVR registration, click ‘Group Setup’ in Main Screen. 2) Click ‘Add Group’and input group name. Drag camera ch user wants as shown below, and set ch displays in Group and click ‘Save Array’ to set up group.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR CHAP. 8 DDNS Web Server * Register DVR for DDNS Web-server and set DVR as shown below, 8-1. Registering DVR for DDNS (DDNS Web-server) 1) Please access www.j2kip.com and Register Member ID. 2) Please click DVR Add to register DVR.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR 3) Please click Confirm after inputting DVR information(DVR Name & Mac Address only). 4) Now, DVR is listed on DDNS Web Server without IP and Port number.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR 8-2. DDNS Set Up in DVR * The following setting is a sample for a cable modem connected to DVR directly. 1) Click Menu and Enter into ‘LOGIN -> EXTERNAL DEVICE -> TCP/IP SETUP’ 2) Go to IP Config Setup, if user set DHCP ‘Automatic’, it detects IP address automatically. IP CONFIG SETUP MAC ADDRESS ___________ 00-0A-A2-00-00-00 ___________ 192.168.001.160 ___________ 50000 ___________ 192.168.001.001 ___________ 255.255.255.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR 4) Set DDNS ON/OFF “ON”. IP address which is assigned from DHCP Server is automatically input on DNS Server. DDNS SETUP DDNS ON/OFF OFF DDNS SERVER 211.062.253.087 INTERVAL D-00 H-00 M-20 REGISTER -------------------------------------------------------------------------DDNS STATUS REGISTER OK 192.168.001.160 IP ADDRESS IP PORT 5000 REMAIN TIME D-00 H-00 M-20 LAST REGISTERATION DATE > WED.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR 6) Go to your PC again after you see “SUCCESS TO REGISTER DVR INFO.” and then Click ‘refresh’ button. Then, DDNS Server automatically catches your DVR’s IP address and Port number. Note. Before using Web-Viewer, please add www.j2kip.com on Trusted Sites at first installation as follows.
Network (JPEG2000+H.264) CHAP 8.
Network (JPEG2000+H.264) CHAP 8. DDNS Web Server Network Stand Alone DVR 8-3. Web Program Some functions of IRS (Integrated Remote Station) such as Viewer,Backup and Player are also available on the web. *If ActiveX control installation is required for the first time access,please click ‘Yes’. Click these icons, then it connects to DVR automatically via DDNS Server. Input information needed for network connection to DVR manually.
Network (JPEG2000+H.264) CHAP. 9 Programmer reference Network Stand Alone DVR CHAP.
Network (JPEG2000+H.264) CHAP.
Network (JPEG2000+H.264) CHAP. 10 Specifications Network Stand Alone DVR CHAP.
Network (JPEG2000+H.264) CHAP. 11 Remocon Key Definition Network Stand Alone DVR CHAP. 11 Remocon Key Definition 1.
Network (JPEG2000+H.264) CHAP. 11 Remocon Key Definition Network Stand Alone DVR CHAP. 11 Remocon Key Definition 2.
Network (JPEG2000+H.264) CHAP. 11 Remocon Key Definition Network Stand Alone DVR CHAP. 11 Remocon Key Definition 3.
Network (JPEG2000+H.
Network (JPEG2000+H.
Network (JPEG2000+H.
Network (JPEG2000+H.
Network (JPEG2000+H.264) Network Stand Alone DVR 16Channel Network Stand Alone DVR Audio, USB Backup available Record & Playback : JPEG2000 / Transmission via IP network : H.