Thank you for purchasing our product. Please read this User’s Manual before using the product.
Safety Precautions CAUTION RISK OF ELECTRICAL SHOCK. DO NOT OPEN ! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This label may appear on the bottom of the unit due to space limitations.
About this document Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users Manual. Pay particular attention to the parts that are marked NOTICE. Also, when connecting with external application, first turn the power OFF and follow manual instruction for appropriate installation. Before reading this document 1. This document is intended for both the administrator and users of stand alone DVR Model. 2.
Content Safety Precautions………………………………………………………………………………………………… 2 About this document………………………………………………………………………………………………. 3 Before reading this document……………………………………………………………………………………. 3 Unite Description of Front Panel………………………………………………………………………………… 5 Unit Description of Rear Panel……………………………………………………………………………………6 Installation………………………………………………………………………………………………………….. 7 Function Setup…………………………………………………………………………………………………….. 15 Login………………………………………………………………………………………………………….
Unit Description of Front Panel 4 split screen 1 ~ 4 full screen / password Sequence / Freezer / Zoom / Water Mark(PTZ mode) / Information MENU button / PLAY button / REC. record button LOCK key lock button BACKUP data back up button / T-SRH time search playback button ESC function exit button Value change button Direction UP / Down, Direction Left / Right Record and play stop, Playback forward or reverse. Playback pause / steps.
Unit Description of Rear Panel Power cord in 12V/5A, power switcher (ON / OFF) 75 Ohm ON/OFF (high/low adjust) Camera 1 ~ 4 in and looping out Audio channel VGA output. PC monitor connector. VG A (Optional) input x 1 and output x 1 Main Monitor S-Video (Y/C) monitor RS-485 LAN. Network connector Control keyboard connector RS-232 connector (ISP. For RD control) Alarm connector Notice: Reboot DVR after installing any device.
Installation Procedure 1) Camera Connection Connect the camera to the CAMERA INPUT CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4 MONITOR on the Rear Panel of the 4 CH DVR.
NOTICE: Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND, and it is recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit. 5 V Internal Circuit D1 Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher than 5V. 5) Network Connection DVR connects to LAN ETHERNET rks TERATRAY CONNECTION ◆To view video image on the computer through internet with DVR view software.
5) HDD connection 1 How to connect single HDD 2 I/O BOARD How to connect 2 HDD I/O BOARD 1 2 1 1 MASTER tie 2 2 MAIN BOARD HDD1 3 MASTER MAIN BOARD 3 HDD SLAVE HDD2 3 Set the drive jumpers as specified by hard disk drive manufacturer. 1. Make sure the HDD is MASTER. 2. Make sure the cable connector is 1. correct. 3. Set the drive jumpers as specified by hard disk drive manufacturer. 2. Please check the HDD panel for Master set up. Make sure the HDD is MASTER and SLAVE.
Picture Full screen or split screen display Press button, to display 4 split screen. Press numeric buttons to display the desired camera image in full screen. 1.) FREEZE Mode 1. In live mode press 2. Press (FREEZE) button to freeze image. again to cancel freeze mode. 2.) Zoom Mode(Display Enlargement.) Go to full screen mode with numeric buttons at live or playback mode, then press ZOOM button to display screen Enlargement. Use button to move position. 3.
6.) BACKUP. Image backup mode.(Image back up must be done on playback mode only.) Locate the playback point of which you want. Press BACKUP, back up menu shows: CDRW / USB CDRW BACKUP MENU USB BACKUP MENU BACKUP MENU START BACKUP TO CDR CDR WRITE SPEED x1,x2,x3 FORMAT USB FORMAT USB START BACKUP TO CDR START BACKUP TO USB CDR WRITE SPEED START BACKUP TO USB USB: The BACKUP CAUTION window pop-up. Press ENTER to begin data back up. Capacity of USB device is not limit.
Compatible USB: Transcend 256 MB, 1 GB / A-DATA, 512MB / USB Flash Drive 128 MB / Intelligent Stick 256 MB / SOLOMON 128 MB / ISTEC 1GB. CD-RW: xxx K (Presently back up progress) Press BACKUP to stop saving. Or wait for CD is full done. xxx K Data only read in Netviewer. 7.) Key Lock function >On the Live mode, press (lock), Only, numeric, freeze, auto, and zoom buttons could work. Press lock key again to enter the login-in window. Enter admin or user password to unlock.
Playback 1. Playback Mode 1) Press PLAY button to begin playback. (System playback the images backward) 2. T-SRH button MAIN PLAY PAGE 1) T-SRH: Playback by time search. Press T-SRH button to active playback function. 1.MASTER TIME LIST 2.SLAVE TIME LIST 3.MASTER EVENT LIST Press direction button 4.SLAVE EVENT LIST UP/DOWN to choose 5.GOTO DATE: 2004/12/31 items. 6.GOTO TIME: 12:12 7.
2) EVENT LIST (Alarm List): Event source- Video loss / Alarm trigger / Motion / Record EVENT LIST +10 NO Y / M / D H : M CH EVENT 10 items display on each page / Total 5000 items display for 500 pages. When event list is out of compass, the total items are less then 5000. NO Y / M / D H : M CH EVENT >Event happens time and list. CH: Event Channel Display. >1 CH ~ 4 CH +10 : Display pages by 10 units / +100 : Display pages by 100 units / +1000 : Display pages by 1000 units.
Function Setup LOGIN 1) Press MENU button to enter into menu. You could do the system function setup in MENU. 2) Password enter window pop-up: CHECK PASSWORD MENU PASSWORD (*****) Default password (Account-Admin) : 44444 Default password (Account-User) : 11111 3) Press numeric (1 ~ 10 )button or remote controller ( 1 ~ 10 )to choose password. 4) Remote controller function buttons are same as DVR panel function buttons.
Basic Operation Press MENU button to enter MAIN SETUP PAGE. MAIN SETUP PAGE 1. HDD INFORMATION 2. DATE-TIME SETUP 3. DISPLAY SETUP 4. CAMERA SETUP 5. BUZZER SETUP 6. RELAY SETUP 7. SYSTEM SETUP 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN 1) Use direction button up/down 2) Press button to select setup item. button to enter into sub-menu function setup. 3) Press sub-menu item with direction button up/down or left/right button.
1. HDD INFORMATION MAIN SETUP PAGE 1. HDD INFORMATION POSITION SIZE USED BRAND 2. DATE-TIME SETUP MASTER 3. DISPLAY SETUP LAST TIME 4. CAMERA SETUP SLAVE 5. BUZZER SETUP LAST TIME 6. RELAY SETUP 7. SYSTEM SETUP MENU, ESC: EXIT, 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN - 2 hard disk information display. Information display: POSITION SIZE USED BRAND >POSITON: Master / Slave >SIZE: Hard Disk capacity. xxGB. Maximum display is 999MB >USED: 00 ~ 100 %. Hard disk overwrites 100 ~ 199 %.
2. DATE-TIME SETUP MAIN SETUP PAGE 1. HDD INFORMATION DATE-TIME SETUP PAGE 2. DATE-TIME SETUP 1. DATE 2000 / 00 / 00 3. DISPLAY SETUP 2. TIME 4. CAMERA SETUP 3. FORMAT 5. BUZZER SETUP 3. DISPLAY AT xx LINE(S) 6. RELAY SETUP 7. SYSTEM SETUP MENU, ESC:EXIT, :MODIFY 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN 1. DATE 2. TIME: > Use direction button up/down choose position, values change button to change date and time values. Do not need to stop hard disk working (Play or record). 3.
3. DISPLAY SETUP MAIN SETUP PAGE DISPLAY SETUP PAGE 1. HDD INFORMATION 1. DATE-TIME ON 2. DATE-TIME SETUP 2. CAMERA TITLE ON 3. DISPLAY SETUP 3. PB DATE-TIME ON 4. CAMERA SETUP 4. PB CAMERA TITLE ON 5. BUZZER SETUP 5. PB DUMMY CAMERA ON 6. RELAY SETUP 6. DVR STATUS ON 7. SYSTEM SETUP 7. BORDER COLOR WHITE MENU, ESC:EXIT, :MODIFY 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN 1. DATE-TIME: Date and Time caption display mode on or off setup. >ON / OFF 2.
4. CAMERA SETUP MAIN SETUP PAGE 1. HDD INFORMATION 2. DATE-TIME SETUP 3. DISPLAY SETUP 4. CAMERA SETUP 5. BUZZER SETUP 6. RELAY SETUP 7. SYSTEM SETUP 8. ADVANCED SETUP CAMERA SETUP PAGE 1. COLOR SETUP 2. TITLE SETUP 3. SCREEN POSITION SETUP 4. V-LOSS DISPLAY SETUP 5. VIDEO MASK SETUP MENU, ESC: EXIT, ENTER: RUN MENU, ESC: EXIT, ENTER: RUN >>DEFAULT RESET<< MENU,ESC:EXIT, 71.66068 Tm(EXIT)Tj0 10.
(2.) TITLE SETUP: Input TITLE of each camera. 9 characters can be input. TITLE SETUP PAGE CAMERA SETUP 1. COLOR SETUP 2. TITLE SETUP 3. SCREEN POSITION SETUP 4. V-LOSS DISPLAY SETUP 5. VIDEO MASK SETUP CH 01 (01 ) CH 02 (02 ) CH 03 (03 ) CH 04 (04 ) MENU, ESC: EXIT: : MODIFY Press direction button up/down/left/right to choose items and position. Press values change button to change values.
(3.) SCREEN POSITION SETUP **** SCREEN POSITION**** UP CAMERA SETUP 1. COLOR SETUP LEFT RIGHT 2. TITLE SETUP 3. SCREEN POSITION SETUP DOWN 4. V-LOSS DISPLAY SETUP ENTER : DEFAULT 5. VIDEO MASK SETUP ESC : QUIT 1. Press direction buttons up/down/left/right to move screen position. 2. Press ENTER button for default. 3. Press ESC button to quit.
(4.) V-LOSS DISPLAY SETUP VLOSS SETUP PAGE **V-LOSS FUNCTION: CAMERA SETUP CH 01 : ON 1. COLOR SETUP CH 02 : ON 2. TITLE SETUP CH 03 : ON 3. SCREEN POSITION SETUP CH 04 : ON 4. V-LOSS DISPLAY SETUP 5. VIDEO MASK SETUP MENU, ESC: EXIT: ** V-LOSS FUNCTION: ON / OFF CH 01 : ON / OFF CH 02 : ON / OFF CH 03 : ON / OFF CH 04 : ON / OFF PS. If choose on, X icon displays beside camera title. Press direction buttons up/down/left/right to choose items. Press values change button to change values.
(5.) VIDEO MASK SETUP VIDEO MASK SETUP PAGE **VIDEO MASK FUNCTION: CAMERA SETUP CH 01 1. COLOR SETUP CH 02 2. TITLE SETUP CH 03 3. SCREEN POSITION SETUP CH 04 4. V-LOSS DISPLAY SETUP 5. VIDEO MASK SETUP MENU, ESC: EXIT: : MODIFY **VIDEO MASK FUNCTION: ON / OFF CH 01 : ON / OFF CH 02 : ON / OFF CH 03 : ON / OFF CH 04 : ON / OFF MASK means the channel would not display on the live screen, but still can set it on recording. Press direction buttons up/down/left/right to choose items.
5. BUZZER SETUP MAIN SETUP PAGE BUZZER SETUP PAGE 1. HDD INFORMATION **BUZZER FUNCTION 2. DATE-TIME SETUP BUTTON BUZZER ON 3. DISPLAY SETUP ALARM BUZZER ON 4. CAMERA SETUP MOTION BUZZER ON 5. BUZZER SETUP V-LOSS BUZZER ON 6. RELAY SETUP HDD-FULL BUZZER ON 7. SYSTEM SETUP CRASH ON BUZZER ON 8. ADVANCED SETUP MENU, ESC: EXIT: : MODIFY MENU, ESC: EXIT, ENTER: RUN **BUZZER FUNCTION: All buzzer function >ON / OFF 1. BUTTON BUZZER? > ON / OFF 2. ALARM BUZZER? > ON / OFF 3.
6. RELAY SETUP MAIN SETUP PAGE 1. HDD INFORMATION RELAY SETUP PAGE 2. DATE-TIME SETUP **RELAY FUNCTION: ON 3. DISPLAY SETUP 1. ALARM RELAY: ON 4. CAMERA SETUP 2. MOTION RELAY: ON 5. BUZZER SETUP 3. V-LOSS RELAY: ON 6. RELAY SETUP 4. HDD-FULL RELAY: ON 7. SYSTEM SETUP 5. CRASH ON 8. ADVANCED SETUP MENU, ESC: EXIT, ENTER: RUN **RELAY FUNCTION: ON 1. ALARM RELAY: ON 2. MOTION RELAY: ON 3. VLOSS RELAY: ON 4. HDD FULL RELAY: ON (Relay on if hard disk record only once.
7. SYSTEM SETUP MAIN SETUP PAGE SYSTEM SETUP 1. HDD INFORMATION 1. DWELL INTERVAL 2. DATE-TIME SETUP 3. DISPLAY SETUP 4. CAMERA SETUP 5. BUZZER SETUP 6. RELAY SETUP 7. SYSTEM SETUP 2. LANGUAGE 3. VIDEO INPUT 4. RS-485 ID 5. RS-485 PROTOCOL 6. RS-485 BAUD RATE UPTIME: xx HRS 8. ADVANCED SETUP MENU, ESC: EXIT: : MODIFY MENU, ESC: EXIT, ENTER: RUN SYSTEM SETUP 1. DWELL INTERVAL: - 0 ~ 999SEC. Full channel and call monitor auto sequence time. 2.
8. ADVANCED SETUP MAIN SETUP PAGE ADVANCED SETUP PAGE 1. HDD INFORMATION 1. ALARM 2. DATE-TIME SETUP 3. DISPLAY SETUP 4. CAMERA SETUP 5. BUZZER SETUP 6. RELAY SETUP 7. SYSTEM SETUP SETUP 2. MOTION SETUP 3. RECORD SETUP 4. PASSWORD SETUP 5. NETWORK SETUP 6. HDD FORMAT 7. FACTORY DEFAULT 8. ADVANCED SETUP 8. SOFTWARE UPDATE MENU, ESC: EXIT, ENTER: RUN ADVANCED SETUP PAGE ALARM SETUP PAGE SETUP 1. ALARM FUNCTION 2. MOTION SETUP 2. ALARM DURATION 3. RECORD SETUP 3.
2. MOTION SETUP MOTION SETUP PAGE ADVANCED SETUP PAGE **MOTION FUNCTION ON 1. ALARM SETUP **MOTION DURATION 2. MOTION SETUP **CHANNEL NUMBER 3. RECORD SETUP 1. SENSITIVITY 4. PASSWORD SETUP 2. VELOCITY 5. NETWORK SETUP 3. ACTIVATION 6. HDD FORMAT 4. RELAY 7. FACTORY DEFAULT 5. MOTION AREA SETUP 8. SOFTWARE UPDATE MENU, ESC: EXIT: : MODIFY MOTION SETUP **MOTION FUNCTION (For all channels) -ON / OFF **MOTION DURATION -10 ~ 999. Motion buzzer and record duration time.
> MOTION AREA SETUP < All area detect with factory default. Press ENTER button to change mode and then increase or reduce. For example: Clear lattices Press value change button to reduce.
3. RECORD SETUP ADVANCED SETUP PAGE RECORD SETUP 1. ALARM 1. HDD FULL SETUP 2. MOTION SETUP 2. RECORD SPEED 3. RECORD SETUP 3. RECORD MODE 4. PASSWORD SETUP 4. RECORD AUDIO 5. NETWORK SETUP 5. QUALITY 6. HDD FORMAT 6. SCHEDULE SETUP 7. FACTORY DEFAULT 7. CHANNEL SETUP 8.
2) RECORD SPEED: Record FPS setup -1/30(1/30), 1/15(1/15), 1/10(1/10), 1/5 (1/5), 1/3 (1/3), 1/2 (1/2), 1(1), 2(2), 3(3.13), 5(5), 10 (8.33), 15(12.5), 30(25), 60(50), 120(100). NTSC / (PAL) 3) RECORD MODE: Record mode setup. -ALWAYS / SCHEDULE / EVENT / EVENT ON SCHEDULE / EVENT + SCHEDULE 4) RECORD AUDIO: Audio record setup -ON / OFF. (Suggest not fewer than 5 fps.
>SCHEDULE SETUP< RECORD SETUP 1. HDD FULL Press direction buttons up/down to 2. RECORD SPEED SCHEDULE items. 3. RECORD MODE 4. RECORD AUDIO Press values change button to change values. 5. QUALITY 6. SCHEDULE SETUP Factory default is everyday all schedules time on 7. CHANNEL SETUP recording. SCHEDULE SETUP CURSOR STEP 30MIN / 6MIN SUN MON TUE WED THU FRI SAT Press direction buttons up/down/left/right to see date and time difference.
30MIN SCHEDULE SETUP CURSOR STEP SUN 00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 00:30 01:30 02:30 03:30 04:30 05:30 06:30 07:30 08:30 09:30 10:30 11:30 12:30 13:30 14:30 15:30 4:30 17:30 18:30 19:30 20:30 21:30 22:30 23:30 MON 00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 4:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 00:30 01:30 02:30 03:30 04:30 05:30 0
7) RECORD CHANNEL SETUP PAGE RECORD SETUP RECORD CHANNEL SETUP PAGE 1. HDD FULL 2. RECORD SPEED CH 01 3. RECORD MODE CH 02 4. RECORD AUDIO CH 03 5. QUALITY CH 04 6. SCHEDULE SETUP MENU, ESC: EXIT: 7. CHANNEL SETUP CH 01 : ON / OFF CH 02 : ON / OFF CH 03 : ON / OFF CH 04 : ON / OFF PS. Choose off if no video input channel or which channel would not do record. According to channel record, record time would different. Press direction buttons up/down to choose item.
4. PASSWORD SETUP ADVANCED SETUP PAGE 1. ALARM SETUP 2. MOTION SETUP PASSWORD SETUP PAGE 3. RECORD SETUP 1. LEVEL:( ) 4. PASSWORD SETUP 2. ADMIN:( ) 5. NETWORK SETUP 3. USER :( ) 6. HDD FORMAT 7. FACTORY DEFAULT 8. SOFTWARE UPDATE 1) Press direction buttons up/down/left/right to LEVEL (Log In level ID type setup) Choose items position. >NONE / ADMIN / USER -ADMIN Press values change button to change values. -USER -NONE, user does not need to insert password before enter in MENU.
5. NETWORK SETUP ADVANCED SETUP PAGE TCP-IP SETUP PAGE 1. ALARM 1. SPEED:>512K SETUP 2. MOTION SETUP 2. DVR NAME:[dvr16] 3. RECORD SETUP 3. NET TYPE: OFF 4. PASSWORD SETUP 4. STATIC IP SETUP 5. NETWORK SETUP 5. PPPOE ID SETUP 6. HDD FORMAT 6. DNS/DDNS SETUP 7. FACTORY DEFAULT 7. SERVER PORT SETUP 8. SOFTWARE UPDATE MAC ADDR: xx.xx.xx.xx.xx.xx 1. SPEED : >512K / 512K / 256K / 128K / 64K > Upload speed. Choose the close speed by applied. 2. DVR NAME: [ x 15 space ] 3.
5. PPPOE ID SETUP If users apply the dynamic IP from ISP, then should input ID and password that from ISP information list. And then go to set DNS/DDNS SETUP For example: Address name is 123456@hinet.net.tw Password is 654321 PPPOE ID SETUP PPPOE ID SETUP 1. LOGIN ID: [ x 20 space] 1. LOGIN ID: [ 123456@hinet.net.tw] 2. 2. :[ x 20 space] :[ 3. PASSWORD: [ x 20 space] 3. PASSWORD: [ 654321] 4. CLEAR PPPOE SETUP 4. CLEAR PPPOE SETUP ] Or Notice: PPPOE ID SETUP 1.
6. DNS/DDNS SETUP Whatever user apply a free or pay DDNS, user needs to input every thing below. DDNS apply: User can get a free hostname or pay from website below. 1. http://www.3322.net/ (China) 2. http://www.changeip.org/ 3. http://www.dyndns.com/ 4. http://www.no-ip.com/ 5. http://www.dhs.org/ 6. http://www.dtdns.com/index.cfm?fuseaction=info.hosts For example: Go to: http://www.dtdns.com/index.cfm?fuseaction=info.hosts Click sign up to create an account.
Fill your information to sign up paper. After, go to email account to get activate ID and code.
Fill ID and code.
Type Hostname and choose a domain name, and then click Add Hostname. EX: Hostname = Myhostname, Domain = 4irc.
Data confirm done, then you can go to DVR advanced setupÆ Network setup now. Advanced setup Æ TCP-IP SETUP TCP-IP SETUP PAGE TCP-IP SETUP PAGE 1. SPEED:>512K 1. SPEED:>512K 2. DVR NAME:[dvr16] 2. DVR NAME:[Myhostname ] 3. NET TYPE: OFF 3. NET TYPE: OFF 4. STATIC IP SETUP 4. STATIC IP SETUP 5. PPPOE ID SETUP 5. PPPOE ID SETUP 6. DNS/DDNS SETUP 6. DNS/DDNS SETUP 7. SERVER PORT SETUP 7. SERVER PORT SETUP MAC ADDR: xx.xx.xx.xx.xx.xx MAC ADDR: xx.xx.xx.xx.xx.
6. DNS/DDNS SETUP DNS/DDNS SETUP DNS/DDNS SETUP 1. D.N.S 1: 000.000.000.000 9. D.N.S 1: 000.000.000.000 2. D.N.S 2: 000.000.000.000 10. D.N.S 2: 000.000.000.000 3. SERVER : DHS 11. SERVER : DTDNS 4. DOMAIN: [ x 20 space] 12. DOMAIN: [ 4irc.com 5. LOGIN ID:[ x 20 space] 13. LOGIN ID:[ your DTNS long in name 6. 14. :[ x 20 space] ] :[ ] ] 7. PASSWORD: [ x 20 space] 15. PASSWORD: [your DTNS long in password ] 8. CLEAR DDNS SETUP 16.
6. HDD FORMAT ADVANCED SETUP PAGE 1. ALARM Press direction buttons up/down to SETUP 2. MOTION SETUP HDD FORMAT items position. 3. RECORD SETUP Press ENTER to format all HDD. 4. PASSWORD SETUP 5. NETWORK SETUP Caution: User can format HDD only when 6. HDD FORMAT all HDD stop record or playback. 7. FACTORY DEFAULT 8. SOFTWARE UPDATE Æ HDD FORMAT CAUTION!! : ** HDD FORMAT CAUTION!!** ALL DATA IN HDD WILL BE Press ENTER button to format hard disk. DESTROYED!! PRESS [ENTER] TO FORMAT.
7. FACTORY DEFAULT ADVANCED SETUP PAGE 1. ALARM SETUP 2. MOTION SETUP Press direction buttons up/down to 3. RECORD SETUP FACTORY DEFAULT items position. 4. PASSWORD SETUP Press ENTER to restore. 5. NETWORK SETUP 6. HDD FORMAT 7. FACTORY DEFAULT 8. SOFTWARE UPDATE ** CAUTION!! ** Press ENTER button to restore. ALL SETUP VALUE WILL BE CLEAR, AND RESTORE FACTORY DEFAULT!! PRESS [ENTER] TO RESTORE. Press ESC button to cancel. PRESS [ESC] TO CANCEL. 8. SOFTWARE UPDATE ADVANCED SETUP PAGE 1.
USB Data Read and Networking 1. Windows 2000 / XP, select small character display. 2. Resolution 1024 x 768. 3. RAM up to 128 MB, system up to PIII-800. 4. Double click SETUP.EXE of CD, and then start to install. 5. User can go to company server to download AP software. 6. Browse install path and then click Next.
7. Advice resolution 1024 x 768. According computer equipment, please choose suitable resolution 8. Select Start Menu Folder, and then click Next.
9. Click create a desktop icon or not, select DVR type, and then click Next. 4 CH and 16 CH DVR Net viewer is suitable. Only some split screen can not display. 10. Click INSTALL to start install.
11. Click Launch NetViewer and click Finish to done.
12. Click Setting. Name: Name the IP address position.(Each name and IP saves every different input) 1 ~ 16 full screen select. IP Addr: Input DVR IP address. Full / Quad / 9 split / 16 split AVI codec: Different computer equipment; different AVI format. 6 split / 8 split / 10 split / 13 split Microsoft Windows Media video 9 is better. Or Cinepak Codec by Radius(Slow transmission, better quality) / Microsoft Video 1(Fast transmission, bad quality). Video: Fullsize, Halfsize: screen size choose.
Click DDNS Host Name: Type DVR DDNS host name: Myhostname.4irc.com CMD Port: command port 21 or 1025 ~ 5999. It is same as DVR network setup. Which is same DVR MENU Æ ADVANCED SETUP Æ NETWORK SETUP Æ DVR NAME: TCP-IP SETUP PAGE 1. SPEED:>512K 2. DVR NAME:[Myhostname ] 3. NET TYPE: OFF 4. STATIC IP SETUP 5. PPPOE ID SETUP 6. DNS/DDNS SETUP 7. SERVER PORT SETUP MAC ADDR: xx.xx.xx.xx.xx.xx DNS/DDNS SETUP 1. D.N.S 1: 000.000.000.000 2. D.N.S 2: 000.000.000.000 3. SERVER : DTDNS 4. DOMAIN: [ 4irc.com ] 5.
13. Click Login, depends on limits of authority. (ID / password is same as DVR) Factory ID is user login. Input admin if you are an administer. Must input on little character. Factory: Password, admin : 44444, user : 11111. Password displays when log in, user just needs to input ID. User log in, no PlayBack function authority. Total 6 people log in. Admin x 1, user x 5. Click OK, after about 5 seconds, admin login!! Message popup. And then click Connect to start.
14. Click Connect, after about 2 ~ 3 seconds to start connect LAN or WAN. Click Disconnect to stop. If the NETWORK is connecting success, the blue light would keep glisten Else, blue is always on light or not display, the connecting is failed. Click live / PlayBack / BackPlay mode. Live: DVR live watching. PlayBack: Change to playback mode. After 2 ~3 seconds to change.
PLAY: Click RUN around 2 ~ 30 seconds to start play first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup. Please try again play or connect again. Click STOP to end playback. TIME LIST: Click RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to start play first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup. Please try again play or connect again.
-Master HDD Event Lists: -Slave HDD Event Lists: Click RUN, time lists popup. On the item, double click date and time to start play, around 2 ~ 30 to start play first record. If over 30 seconds, cannot find any file or network disconnect, Time out message popup. Please try again play or connect again. Click STOP to end playback.
15. Backup Play: - Click Open to choose file path.
Click Play to start backup data play. Click Stop to end. Click Pause to temporary stop playback. Click Resume to restart. Choose camera, click mouse right button. Camera 1 ~ 4 switches or reset all. Click Save “CamNo xx image . / save image all to save current image. Save path is C:\DVR.
4. AVI transfer: Click Backup Play AVI : On live or playback mode, save files to .DVR file. And then OPEN file, press play to start playback. Press AVI button to start record AVI file. Press again to stop. Only 2 cameras selectable.
Record Time Table: 80GB HD Record Quality: Low. KB Range: Lowest: 13, Highest: 20. Average: 17. REC FPS 120 60 30 15 10 REC Hour 11 22 45 91 137 REC FPS 5 3 2 1 1/2 REC Hour 274 456 685 1370 2741 REC FPS 1/3 1/5 1/10 1/15 1/30 REC Hour 4112 6853 13706 20565 41140 Record Quality: Normal. KB Range: Lowest: 14, Highest: 25. Average: 20.
VGA Description (Optional) Accessories: 1. 20 PIN Male to Female D-SUB pin cable X 1 2. VGA PCB bracket X1 3. Screws X4 1. VGA board introduction. VGA connector Socket 2. Resolution switcher table Pin 4 Resolution Pin 1 Pin 2 Pin 3 640X480 60HZ ON ON ON 800X600 60HZ ON ON OFF 1024X768 60HZ ON OFF ON 640X480 75HZ ON OFF OFF 800X600 75HZ OFF ON ON 1024X768 75HZ OFF ON OFF Resolution and switcher description. Step. 1 DVR Power on. NTSC / PAL auto detects. Step.
Additional Hard Disk x 2 can be installed on DVR base. Both are 2-iron slices immobile type. 2 Iron slices are in the accessories box, please tell supplier if slices are not exist 2-iron slices immobile type: Slices immobile type: 4 screws hole on each slice. 2 for DVR base fixed. Another 2 for hard disk fixed. Hard disk install.: Locking hard disk screws, then locking DVR base screws to fixed on.
P / T / Z Dome mode. 6. ADVNACED SETUP PAGE Æ P.T.Z SETUP ADVANCED SETUP PAGE 1. ALARM SETUP 2. MOTION SETUP 3. RECORD SETUP PTZ SETUP PAGE CHANNEL NUMBER 1. ID 2. PROTOCOL 4. PASSWORD SETUP 3. BAUDRATE 5. NETWORK SETUP 6. P.T.Z 4. AUTO TOUR SETUP 5. LINE SCAN 7. HDD FORMAT 6. AUTO FOCUS 8. FACTORY DEFAULT 7. AUTO IRIS 9. SOFTWARE UPDATE PTZ SETUP PAGE CHANNEL NUMBER: CH01 ~ CH4 1. ID: 01 ~ 4 2. PROTOCOL: PELCO-P / PELCO-D / LILIN / ABC / ELITAR / DENTEC-D / DENTEC-P / OFF 3.
Front Panel Button Comparison: W.M.: To P / T / Z mode PLAY / REC = IRIS off / IRIS open = FOCUS near / FOCUS far BACKUP / T-SRH = ZOOM IN / ZOOM OUT MENU = P / T / Z Dome Menu FRE. : To Preset mode. PRESET: 000 glisten on left-up corner. Moves P / T / Z dome to the position user wants. When “PRESET: glistening”, press number button. EX: 1 ~ 9. 10 = 1 + 10, 11 = 1 + 1, 12 = 1 + 2, 21 = 2 + 1, 132 = 1 + 3 + 2. ZOOM : After press ZOOM button to save the presets. INFO : Press FRE. button into preset mode.
IE Networking Software 1. This web is for preliminary IE browser. 2. User can download the network viewer from this web page or view the DVR video image in the future. 3. The AP software is already saved to DVR system IC. User needs to do is: a.) Go to Advanced SetupÆ Network SetupÆSets LAN or WAN IP address of DVR. b.) Open IE browser, and then into your IP on the IE address bar. c.