Ernitec EDNS V1000 series User manual
Ernitec EDNS V1000 series – user manual Caution and Preventive Tips Handle with care, do not drop the unit Mount the unit in an equipment rack or place it on a solid, stable surface Indoor use only. Do not place the unit in a humid, dusty, oily, or smoky site Do not place it in an area with poor ventilation or in an area close to fire or other sources of heat.
Ernitec EDNS V1000 series – user manual Important Information Before proceeding, please read and observe all instructions and warnings in this manual. Retain this manual with the original bill of sale for future reference and, if necessary, warranty service. When unpacking your unit, check for missing or damaged items. If any item is missing, or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT. Contact your dealer for assistance.
Ernitec EDNS V1000 series – user manual Table of Content 1. Overview .......................................................................................................................6 2. System Setup ................................................................................................................7 2.1 Position the DVR .................................................................................................7 2.2 Connect Devices to the DVR ........................................
Ernitec EDNS V1000 series – user manual 3.6.5.3 3.6.6 3.6.7 3.6.8 3.7 Alert IP .................................................................................. 40 3.6.5.4 Alert Port ............................................................................... 40 3.6.5.5 Alert Interval .......................................................................... 40 Event Full Screen ................................................................................. 41 Event Duration .....................
Ernitec EDNS V1000 series – user manual 4.4.2.1 ezBurn Introduction ................................................................. 61 4.5 4.6 4.4.2 Export Normal Video ............................................................................ 62 4.4.3 Export Event Video ............................................................................... 62 Dome Control..................................................................................................... 63 4.5.1 Dome Connection ..........
Ernitec EDNS V1000 series – user manual 1. Overview EDNS V1000 DVR is an integrated digital video recorder that combines the features of a time-lapse audio / video recorder, a multiplexer, and a video server to create a single security solution. Its outstanding quadplex operation enables users to view live video, search and playback any recorded video by date/time or event, and remotely monitor the unit via internet on PC, MEANWHILE the recording of the DVR unit is ongoing simultaneously.
Ernitec EDNS V1000 series – user manual 2. System Setup The notices and introduction on system installation will be described particularly in this chapter. Please follow the description to operate the unit. In order to prevent the unit from data loss and system damage that caused by a sudden power fluctuation, use of an Uninterruptible Power Supply (UPS) is highly recommended 2.
Ernitec EDNS V1000 series – user manual Connecting Short-term Device If any short-term devices shall be installed to the DVR as parts of the unit system, such as USB ThumbDrive® or any USB devices, etc, make sure those devices are connected only after the unit is powered up. The reason is because the DVR can recognize the external devices only after the power-up process is done completely. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual 2.3 Rear Panel Connections There are various connectors on the rear panel for the DVR installations. For different models, the connectors vary accordingly. Refer to Setup Guide for actual provided connectors. The following shows the detailed description of each connector. Main Monitor (BNC/ VGA/ Digital Output) The DVR supports three different types of main monitor: BNC, VGA, or Digital Output.
Ernitec EDNS V1000 series – user manual Video Out (selected models only) Video out connectors are provided for looping out the video sources of the connected cameras. Audio Out – Main & Call (selected models only) Main & Call Audio Out RCA connectors are provided for connecting the DVR to audio output devices (e.g. amplified speakers). “MAIN AUDIO OUT” will output audio from the main monitor, whereas “CALL AUDIO” will output audio form the call monitor.
Ernitec EDNS V1000 series – user manual for detailed pin definitions for different models. Alarm Out (selected models only) Some models provide a terminal block for connection to alarm output devices. Refer to Setup Guide for detailed pin definitions for different models. LAN Connector (RJ-45) The DVR is capable of networking. Once the unit is connected to the LAN network, users can remotely access the unit through the remote software on a PC.
Ernitec EDNS V1000 series – user manual Power Jack (selected models only) Connect the power cord shipped with the unit. Use of other power supply cords may cause overloading. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual 3. General System Setup Before operating the DVR, some general configuration should be setup first. The following subsections will introduce function keys on the front panel and general configuration of the DVR. The regular displayed OSD information and its displayed positions are shown as following figure. Title of the channel will be displayed on the top-left corner of the window, either in full screen mode or in multiple channel mode.
Ernitec EDNS V1000 series – user manual Network LED The LED lights up when the DVR is connected to a network and blinks when the data is being transferred. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual 3.1.2 Function Keys This section describes the functional keys on the front panel of the DVR. Refer to the Setup Guide for the graphical illustration of functional keys. Power Key When the quick shutdown function is enabled, press and hold this key to quick shutdown the DVR. Refer to section Power Up / Shutdown the DVR for more information about the setting of quick shutdown function.
Ernitec EDNS V1000 series – user manual COPY In Playback mode, press COPY to select the start and end time of the export video. Refer to section Video Export for detailed information. CALL (Spot) In Live mode, press this button to enter call monitor control mode. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual PLAY/STOP Press this key to switch between live image and playback video. NOTE: According to record setting, part of the latest video cannot be played back because the video is still saved in the buffer. FREEZE (Pause) Press FREEZE while viewing live image, the live video will be frozen. The date / time information shown on the monitor will continue updating. Press FREEZE again to return to live mode.
Ernitec EDNS V1000 series – user manual Direction Keys In Zoom mode, press these keys to move to desired directions. In the OSD setup menu, the LEFT/ RIGHT keys are used to move the cursor to previous or next fields. To change the value in the selected field, press UP/ DOWN keys. ENTER / ZOOM In OSD setup menu or selection interface, press this key to make the selection or save settings. In live full screen view mode, press this key to view a 2× zoom image. Press it again to exit Zoom mode. V 2.2.
Ernitec EDNS V1000 series – user manual 3.2 Enter OSD Setup Menu The configuration of the DVR can be customized by entering the intuitive Graphical User Interface (GUI) OSD setup menu. Collaborating with a USB mouse, setting up the DVR can be easy as operating on a PC. Press MENU and select an account to login. The next step is to enter a corresponding password. The preset password for the administrator account “admin” is “1234”.
Ernitec EDNS V1000 series – user manual Password Protection Select to request for username and password for accessing functions listed in Authority Setup menu, or select to allow free access. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual Account Setup Setup customized account, password, and privilege level in this menu. Note that the account is case sensitive, and password cannot contain the number “0”. The privilege level rank from levels 1~8, which level 8 has the highest privilege. Alternatively, select to stop using the account. NOTE: The username and authority level of the preset “admin” account cannot be changed.
Ernitec EDNS V1000 series – user manual Power Up the Unit Simply plug in the power adapter that came with the package and the DVR will start to boot. The color bar and system checking information will be shown on the monitor and then disappear when the unit has been completely powered up. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual Restart / Shutdown the Unit Press MENU and input the username and password that has sufficient authority to access the OSD setup menu. Select in Main Menu and press ENTER to enter the Shutdown menu, which displays as follows. Shutdown Power Off Reboot Power Key Privilege EXECUTE EXECUTE Auth Select this item to shut down the unit. Do not remove the power during shut down until the message “You can safely turn off DVR now!” displays.
Ernitec EDNS V1000 series – user manual Direct: For users who wish to enable the quick shutdown function without any confirmation or login process, select this option and the DVR will automatically shutdown after long pressed the Power Key. Disable: Select this option to disable the quick shutdown function. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual 3.3.1 HDD Auto Scan When the DVR is powering on, HDD auto scan will be initiated if there was previously an unusual power loss or file system error. If by any chance auto scan failed, the HDD will need to be formatted. NOTE: If users wish to disable the auto scan function, enter the OSD setup menu via an authorized account and access to set to . Read the following troubleshooting to finish the auto scanning process.
Ernitec EDNS V1000 series – user manual 3.4 System Date / Time Setting Users can set the current date, time and other OSD parameters in Date/Time menu (under System Setup menu). The login account should have authority to access the System Setup menu. In OSD setup menu, select and press ENTER, then select to access the Date/Time menu; the menu displays as follows.
Ernitec EDNS V1000 series – user manual Date Display Mode This function allows users to set the OSD display type of the date. There are three options to select from: , or . “Y” represents “Year”, “M” represents “Month” and “D” represents “Day”. Move to the item and press ENTER, the option starts blinking. Use UP / DOWN keys to change the setting. Time Display Mode Users can set the time format to <12 HR> or <24 HR>. Use the UP / DOWN keys to change the format. 3.4.
Ernitec EDNS V1000 series – user manual 3.4.3 Network Time Protocol Setup Time Zone Select
Ernitec EDNS V1000 series – user manual 3.5 Record Schedule / Quality Setting The Record Setup menu allows users to set recording quality, recording schedules, and other recording parameters. Login with a proper account to access Record Setup menu. In the Main menu, move the cursor to and press ENTER; the following menu is displayed.
Ernitec EDNS V1000 series – user manual NOTE: Since a VBR file does not have a fixed size, the HDD space usage cannot be calculated and thus ezRecord function is not supported for VBR mode. Therefore, if ezRecord is selected as the preset record configuration, the option of this menu item will automatically be set as . 3.5.2 Schedule Setup The Schedule Setup is used to set the day and night time, or weekend recording schedule.
Ernitec EDNS V1000 series – user manual Halfl-D1 mode (NTSC: 720*240@240PPS; PAL: 720*288@200PPS) Normal PPS 15 NTSC (12.5 PAL) V 2.2.082012 Normal Size 10 KB / PIC www.ernitec.
Ernitec EDNS V1000 series – user manual 3.5.4 Per Camera Configuration This function is used to set the Day / Night / Weekend PPS (Picture per Second) and Quality for each channel. The Preset Configuration must be set to for accessing these schedules. The menu is displayed as below.
Ernitec EDNS V1000 series – user manual 3.5.6 ezRecord Setup This item aims to ease the complicated record settings, and to make the setup much easier. Note that the item can be reached only when is selected as the option for .
Ernitec EDNS V1000 series – user manual NOTE: The current number of connected cameras will affect the recording quality automatically calculated through the . Therefore, once the number of connected cameras is changed, the should be reset. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual 3.5.7 Data Lifetime Setup Data Lifetime indicates the duration that a video is saved and recallable in the HDD. Only those video recorded within Data Lifetime can be displayed on the screen and played back. The video exceeded Data Lifetime will be hidden and cannot be retrieved for playback.
Ernitec EDNS V1000 series – user manual be accessible. Enter this menu and users can setup data lifetime of each channel independently. The value ranges from <1> to <365> days. Alternatively, select <0> to disable this function. 3.5.8 Circular Recording Users can choose to record video in circular mode or in linear mode. If circular mode is selected, the DVR will stores new video into the HDD spaces while overwrite the oldest recorded video.
Ernitec EDNS V1000 series – user manual Purge All Data The item is used to delete all recorded video from the database. Set this item to to . Purge All Event Data The item is used to delete all event video from database(s). Using UP / DOWN keys to select and start the deletion by setting to . V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual Purge Event Before The item is used to delete event video before a specific date. Use LEFT / RIGHT keys to move the cursor to next or previous field, ENTER to select the item and UP / DOWN to adjust the value. Start To Purge After the video or data to be deleted are selected, set this item to to start the deletion or choose to cancel. 3.6 Event Setting This menu allows users to determine the DVR’s behavior in response to alarm events.
Ernitec EDNS V1000 series – user manual 3.6.2 Event Icon This item enables (On) / disables (Off) the display of event icons on the monitor when alarm events occur. The event icons are represented by a character according to the event types respectively. Refer to the following table for association of event icons and event types. Event Icon A M L 3.6.3 Event Type Alarm in event Motion detection event Video loss event Email Notice The item enables (On) / disables (Off) the Email notification of an event.
Ernitec EDNS V1000 series – user manual manual. Alert Notification Setup Alert Configuration Set Alert Notification Alert IP Alert Port Alive Interval 3.6.5.1 1 OFF 0.0.0.0 NUM 9999 120 Sec Alert Configuration Set provides 3 combinations of Alert Notification, IP, Port, and Interval. 3.6.5.2 Alert Notification 4 options are included in this item: , , , and . : The Alert Notification is turned off.
Ernitec EDNS V1000 series – user manual 3.6.6 Event Full Screen This function allows the DVR to display the alarm channel in full screen size when an alarm is triggered. Select to disable this function; select to display the alarm channel on Main Monitor when an alarm is triggered; select to display the alarm channel on Call Monitor; and select to display the alarm channel on both Main Monitor and Call Monitor. 3.6.
Ernitec EDNS V1000 series – user manual 3.6.8.3 Motion Detect This item allows users to enable or disable motion detection function of the DVR. Select to enable Motion Detect alarm events, or to disable. If motion detection function is enabled, it is required to define motion detection parameters such as detection area and sensitivity settings in . 3.6.8.
Ernitec EDNS V1000 series – user manual Sensitivity This item is used to set the sensitivity of detection grids for the camera. A greater value indicates more sensitive motion detection. A motion alarm will be triggered once the amount of motion detected exceeds the Threshold value. Move the cursor to and press ENTER, and then use UP/ DOWN keys to adjust the value. The value is increased by 4% increment.
Ernitec EDNS V1000 series – user manual 3.6.8.6 Alarm Out This item allows users to enable/ disable the alarm output on the selected channel to activate the relay. The signal can be a light or siren to caution an alarm event. Select to enable the alarm output, or to disable. 3.7 POS Setup The function provides a connection between the DVR and a Point-of-Sale (POS) device, such as a cash register.
Ernitec EDNS V1000 series – user manual 3.7.3 Exception POS Setup This sub-menu is used to define the conditions that are to be treated as an “Exception” and thus trigger an action (the function will be implemented later). Exception POS Setup Exception No. Trigger Exception String By Numerals Value Value (Upper Limit) 1 On NO SALE Off Exception No. Select a number to set the exception parameters. The total is 16 exceptions. Trigger Select to monitor if transactions satisfy exception parameters.
Ernitec EDNS V1000 series – user manual : When the value of a transaction is greater then or equal to a certain value, it will be marked as an exception. That specific value need to be defined in the following sub-setting . : When the value of a transaction is less than or equal to a certain value, it will be marked as an exception. That specific value need to be defined in the following sub-setting .
Ernitec EDNS V1000 series – user manual Input Source Select the input source of the POS device, either direct connected or connected with the Data Converter. Camera Selection Select a camera to display the text overlay. Text Filter This item is used to choose the text filter. The supported models for pole display and printer are listed as below.
Ernitec EDNS V1000 series – user manual Manual Filter Setup Once enter the Manual Filter Setup menu, users should key in hexadecimal digits. The menu of the item is shown as follows. Manual Filter Setup Header 1 Header 2 30 30 Input Process If a pole display from a PC based POS device will be used, select . is to be selected when using a Pole Display from a Standalone POS device.
Ernitec EDNS V1000 series – user manual Various multi-window view formats are offered for selection. To switch between available viewing formats, press MODE repeatedly. The available view formats are illustrated as the following figure. NOTE: 3x3 viewing mode is only available in 8CH and 16CH models, whereas 4x4 viewing mode is only available in 16CH models. 4.1.2 Digital Zoom Users are able to view a 2× full screen in live mode. To view the 2× full screen, follow the steps.
Ernitec EDNS V1000 series – user manual 4.1.3 View Live Cameras Users are allowed to view live camera in versatile viewing modes, including full-screen, 2×2, 3x3 and 4×4. The general operation under live mode is described as follows. Freeze Live Image Press FREEZE while viewing live image, the image pauses but the date / time information does not, and the system clock continues running. Press FREEZE to pause the live image; press FREEZE again to resume the live camera view. 4.1.
Ernitec EDNS V1000 series – user manual Key Usage in Playback The key usage is slightly different in playback mode. Following is the key usage found in playback mode. LEFT (Reverse Playback): The key is used to reverse the recorded video while the unit is playing back. Press the key repeatedly to increase the speed of reverse playback by 1×, 2×, 4×, 8×, 16×, or 32×. RIGHT (Forward Playback): The key is used to play the recorded video fast forward.
Ernitec EDNS V1000 series – user manual 4.2 Sequence This section introduces the way to view sequence mode with both Main Monitor and Call Monitor, if connected. Sequence function can avoid manual backtracking and provides more flexibility while monitoring surveillance. 4.2.1 Sequence with Main Monitor Automatic sequence function can be observed in any view mode. Select certain view format and press SEQ to toggle the automatic sequence; press ESC to stop sequencing.
Ernitec EDNS V1000 series – user manual Press CHANNEL key to display the associated camera on call monitor. Alternatively, press SEQ repeatedly to display the sequence of cameras previously programmed in Call Monitor Schedule menu. Press ESC to return the front panel to Main Monitor Control mode. 4.3 Search Recorded Video The DVR is capable of searching and playing back recorded video by date / time, events, or text.
Ernitec EDNS V1000 series – user manual Move the cursor to “Select” and press LEFT/RIGHT keys to choose date/ time. Press ENTER and adjust the values by UP/DOWN keys. Press ENTER to confirm the settings or ESC to abort. Move the cursor to and press ENTER to start playing back the selected video. Press PLAY again to return to live video. NOTE: If there is no available recorded video that matches the specified time and date, the unit starts playback from the next available video.
Ernitec EDNS V1000 series – user manual Move the cursor to year/ month and press ENTER. Then press UP/DOWN keys to adjust the value and press ENTER again to confirm. Move the cursor and press ENTER to select any date shown in bold and underlined font. The bar below the calendar will change according to the recorded data of the selected date. Then select preferred time from the time bar. Alternatively, move the cursor to the time shown at the bottom.
Ernitec EDNS V1000 series – user manual Press SEARCH to enter the Search menu. To search event video that has been recorded on a specific camera, use LEFT / RIGHT to move the cursor and press ENTER to select or de-select a channel. Move the cursor to and press ENTER to list the event video of the selected channels. The Event List displays. To exit the event list, press ESC. Follow the steps to playback video from Event List. Press and hold UP / DOWN to scroll through the Event List.
Ernitec EDNS V1000 series – user manual data containing EITHER ONE of the word strings. AND: Enter two sets of word strings. Search for videos with data containing BOTH of the word strings. Specific: Specify one set of word string. Search for videos with data containing the specific word string. By Numerals: Outside The Range: Enter two numbers to specify a range. Search for videos with data containing number(s) out of the range. Inside The Range: Enter two numbers to specify a range.
Ernitec EDNS V1000 series – user manual *.gpg, *.avi (or *.drv), *.sig and readme.txt. Make sure an external storage device is available and connected to the appropriate port for video export. From the Main menu, select and press ENTER. The menu is displayed as below. Export ENTER Ch1 Ch2 Ch3 Ch4 All 2010/12/07 AM 11:50:05 2010/12/09 PM 03:09:18 ENTER Normal DRV No No No Select Device Select Ch: From: To: Select Events Data Type Export Format Digital Signature Erase Disc Begin Export 4.4.1.
Ernitec EDNS V1000 series – user manual 4.4.1.2 Select Video for Exporting Select video from desired channel(s) with specific date / time and/or event(s), and set the item to to start exporting. Following are the items for selecting video. Select Channel Select the channel to export. Move the cursor to the desired channel using LEFT / RIGHT keys, select or de-select a channel by pressing ENTER. From / To Time The items are used to set the time which data export begins and ends.
Ernitec EDNS V1000 series – user manual multiple channels are exported for AVI files, each channel is exported to a separate file. 4.4.1.3 Digital Signature Users can export video clip with or without a digital signature. Set this item to to export with the signature file, or to export without it. Each recorded video with digital signature will be exported into four files, including *.gpg, *.avi (or *.drv), *.sig and readme.txt. The *.
Ernitec EDNS V1000 series – user manual NOTE: Once an external device has been connected to the DVR, the device has priority over the built-in DVD+RW. That means the video will be exported to the external device instead of the built-in DVD+RW. Depending on the size of video, the exporting process may take about 10 minutes to 1 hour. 4.4.2.
Ernitec EDNS V1000 series – user manual 4.4.2 Export Normal Video To Export normal video to external device, follow these step: Press SEARCH and play wanted normal video by entering date and time. Note if the screen is showing in multiple channel mode, please make sure there is no window displaying in Live mode, or the export will not work. After entering playback mode, play the video and press COPY once to mark the starting point of the export video. The playback continues.
Ernitec EDNS V1000 series – user manual ezBurn confirmation Selected Device: USB Storage Device Exported Required Size = 11 MB Export Event Info: Data Time Ch 2011/05/07 AM10:42:35 13 ENTER: YES ESC: NO Type Motion If there is no any exportable device connected to the DVR unit, a warning message will be shown on the screen Press ENTER to start the export the whole event video to the connected device; or, press ESC to abort. 4.
Ernitec EDNS V1000 series – user manual Camera Setup Analog Camera Select Dome Protocol Dome ID Camera Name Hidden Brightness Contrast Saturation Hue CH01 None 0 CH1 No 0 0 0 0 To configure dome protocol, select a camera first and set the communications protocol associated with dome camera using the Direction keys and ENTER. NOTE: The settings become effective after saving the changes and exiting from the menu. 4.5.3 RS485 Setup The DVR controls the domes via RS-485 communication protocol.
Ernitec EDNS V1000 series – user manual 4.5.4 Dome Controlling Buttons After pressed DOME to enter Dome Control mode, a dome control panel will be displayed. The controlling buttons are: Iris Close/Open, Focus Far/Near, Zoom Out/In, Preset, Live, Pan/Tilt Speed, Direction buttons, and Auto Focus. The functions are described as below. Iris Close Click on it to close the Iris on the dome camera. Iris Open Click on it to open the Iris on the dome camera.
Ernitec EDNS V1000 series – user manual Live Click on it to exit Dome Control mode and return to live full-screen viewing mode. Pan/Tilt Speed Users can select preferred pan/tilt speed. Direction Buttons Click on the buttons to pan and tilt the lens of selected dome camera. Auto Focus Click on this button to automatically adjust focus of the dome camera. The front panel keys can also perform the functions listed above. Please refer to Setup Guide for the graphical illustration of functional keys. 4.5.
Ernitec EDNS V1000 series – user manual 1 4 7 Exit 2 5 8 0 3 6 9 Clear BS Set Preset Go Preset Run Tour Input a desired preset number. Click on the button to save the position. Now the preset position is set and ready to be called. 4.5.6 Call Preset Points Follow the steps to call preset points. Press a Channel key to view the corresponding camera in full-screen. Then press DOME to enter Dome Control mode. The dome control panel will be displayed.
Ernitec EDNS V1000 series – user manual 4.5.7 Run Dome Camera Tour Users can also display dome camera tour setup at the dome camera side. Follow the steps to run display of dome camera tour. Press a Channel key to view the corresponding camera in full-screen. Then press DOME to enter Dome Control mode. The dome control panel will be displayed. Click on the dome control panel or press CH1 key to access the Set/Go Preset function. A numeral keyboard will be displayed.
Ernitec EDNS V1000 series – user manual 5. Remote Monitoring Software The remote monitoring software is a remote browser-based software application designed to operate with the DVR products. Using the software, users are allowed to view live and recorded video, and configure the DVRs remotely via a LAN, WAN or Internet on a personal computer.
Ernitec EDNS V1000 series – user manual Hard Disk Drive Operating System Web Browser 5.2 Requires 20 MB for software installation Windows XP, Windows Vista, and Windows 7 Microsoft Internet Explorer version 6.0 or above Monitor Resolution Minimum 1024 x 768 with 16-bit color Network Card 10Base-T (10 Mbps) or 100Base-TX (100 Mbps) operation; must match the network configuration Installation of Software Refer to the following description to install the remote monitoring software. 5.2.
Ernitec EDNS V1000 series – user manual Uncheck “Require server verification (https:) for all sites in this zone”. Type the IP address of the unit in field and click to add this web site to the zone. Click to confirm the setting and close Trusted sites dialog. In the Security Level area, click . The Security Settings screen is displayed. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual Under , set all items to or . Click to apply the setting and close the screen. Click to close Internet Options dialog. Now the installation can continue to the next step. 5.2.2 Install the Remote Monitoring Software Start the browser to initiate the installation of the remote monitoring software on the PC.
Ernitec EDNS V1000 series – user manual NOTE: Do not enter any leading “0” characters in the address, for example, “192.068.080.006” should be entered as “192.68.80.6”. If the default trigger port 80 is changed into another one, take port 81 for example, the IP address should be entered as “192.68.80.6:81”. A version check starts to verify whether the remote monitoring software was installed already, and also check if the version is the same as that stored in that particular DVR.
Ernitec EDNS V1000 series – user manual 5.2.2.1 Login / Logout Login using the same accounts setup in the DVR. The authority is also the same as setup in the DVR. One preset account “admin” and up to two other accounts can access a DVR at the same time. Nevertheless, if the “admin” account is currently accessing the unit’s OSD setup menu via front panel of the unit, then the “admin” account at the remote monitoring site cannot change the settings at the same time.
Ernitec EDNS V1000 series – user manual 5.2.2.2 Software Upgrades If a new version of the remote monitoring software is available on the DVR, upgrade will be prompted while accessing the unit. Follow the steps to upgrade the software. The message as the above figure will be prompted. Click to accept version upgrade. Start the IE again and enter the IP address of the DVR in the Address bar of the browser; or if the unit address is set as a Favorite site, click the Favorites entry for the unit.
Ernitec EDNS V1000 series – user manual operation can be accessed. To choose desired display mode and to operate dome camera control, refer to the following sections. 5.3.1.1 Select Display Mode Choose the number of windows to be displayed on the main window. Click one of the display buttons in MODE section. Available selections are 4, 9 and 16 camera displays. To view certain window in full screen, either double-click on the wanted window, or click on the corresponding CAMERA button. 5.3.1.
Ernitec EDNS V1000 series – user manual Dome ID (ID) Click for changing the dome ID and protocol. Proper authority is required to access this function. Focus +/− Use these buttons to adjust the camera lens to focus on objects for a clear view. Click on to focus near or to focus far. Iris +/− This item is used to open and close the iris to let more or less light into the camera. Click on to open iris or to close iris.
Ernitec EDNS V1000 series – user manual NOTE: The instant recording video will be saved as *.drv file. 5.3.2.2 Playback Instant Recorded Video Follow the steps to playback a video recorded by “Instant Recording”. Click on main window toolbar and click tab. Click to choose a recorded file. Click to start playing the recorded video. 5.3.
Ernitec EDNS V1000 series – user manual To playback remote video segments, follow these steps: Choose in
Ernitec EDNS V1000 series – user manual 5.3.3.3 Playback Controls When the local or remote video is being played, the remote monitoring software is in Playback Mode. The playback controls toolbar will emerge on the main window toolbar. The Playback controls and indicators are described as below. Icon ◄◄ Name Description 1. Click to play the recorded video in backward direction. Click repeatedly to select the backward playback speed: 1×, 2×, 4×, 8×, 16×, Fast Backward / or 32×. Step Backward 2.
Ernitec EDNS V1000 series – user manual 5.3.5 Search from Event List Click SEARCH, the Event List appears. The List contains information about the alarm events that the unit recorded and saved. Up to 1024 events can be listed in the Event List. The Event List displays each event by its number, the date and time of the event, the type of the event (including Alarm In, Motion Detection, Video Loss, and Over Speed), and the camera channel where the event occurred.
Ernitec EDNS V1000 series – user manual Total Size This item indicates the total size of the HDD. State This item indicates whether the HDD is active or non-active. Temperature This item indicates the current temperature of the HDD in Celsius degree. 5.3.8 Remote Monitoring Software Troubleshooting What happened if the server requests to upgrade the software every time the DVR is connected? If the following screen displays repeatedly, please follow the steps to delete the temporary internet files.
Ernitec EDNS V1000 series – user manual Click the button in the field; the screen displays as below. Check the box and click . Now, enter the IP address of the DVR to make the connection again. V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual Appendix A: Recommended HDDs Refer to the following list for some recommended HDDs to be used in the DVR. Brand Seagate HITACHI Maxtor V 2.2.082012 Model Name Model Number Size Pipeline HD.2 ST3500312CS 500G Barracuda ES.2 ST3500320NS 500G Barracuda 7200.11 ST3500320AS 500G Barracuda 7200.12 ST3500418AS 500G Barracuda 7200.11 ST3750330AS 750G Barracuda 7200.12 ST3750528AS 750G Barracuda 7200.11 ST31000340AS 1000G Barracuda 7200.
Ernitec EDNS V1000 series – user manual Appendix B: Remote Controller The operational function keys on the remote control are listed as below figure: V 2.2.082012 www.ernitec.
Ernitec EDNS V1000 series – user manual The keys of the remote control function as the keys of the front panel of the DVR. The only difference between the remote control and the front panel keys is the “DVR SEL” key. The DVR Selection key is used to switch control between each DVR. The remote control can be used to control up to 16 DVRs. To setup the remote control, the first thing is to assign a unique DVR Unit ID to each DVR.
Ernitec EDNS V1000 series – user manual Appendix C: Setup a DVR behind a Router This appendix describes how to set up a router if the DVR connects to the internet via a router. To properly operate a web server, e.g. a DVR, users have to set up both the IP and port of the DVR, which are essential for data and command transmission. The port setting is adjustable in OSD setup menu of the DVR and only one port is needed to do remote operation.
Ernitec EDNS V1000 series – user manual Following is an example of how the router should be set. Router (D-Link DI-724P+) WAN IP: 218.160.54.13 LAN IP: 192.168.0.1 PC IP: 192.168.0.100 DVR 1 IP: 192.168.0.167 Trigger port: 80 DVR 2 IP: 192.168.0.200 Trigger port: 81 To change the setting of the router, a PC with web browser is required. Connect to D-Link DI-724P+ from PC via IE. The setup screen will be shown after entering the correct username and password.
Ernitec EDNS V1000 series – user manual A. Select to set up the service. B. Enter the name of the setting in the Name field: DVR 1. C. Enter Private IP: 167 D. Choose as the Protocol Type. E. Enter Private Port: 80. F. Enter Public Port: 80. G. Click for the Schedule setting. H. Click . Click to go on when the following screen displays. Follow the steps to set up web port forward to DVR 2. A. Click to set up the service. B.