Engine Serial Number: _____________________________________________ Hull Identification Number:__________________________________________ Hull Identification Number • The Hull Identification Number (HIN) is located on the starboard side of the transom. • Record the HIN (and the engine serial number) in the space provided above. • Please refer to the HIN for any correspondence or orders. HIN LOCATION © 2003 Maxum Technical Publications. All rights reserved.
CONTENTS 1 Chapter 1: Welcome Aboard! 16 Chapter 4: Propulsion & Related Systems 1 Dealer Service 1 Warranty Information 16 Engine 16 Special Starting Instructions for Carbureted Engines (If Equipped) 1 Boating Experience 2 Safety Standards 16 Fire Suppression System (If Equipped) 2 Engine & Accessories Guidelines 17 Engine Compartment Ventilation System 3 Engine & Accessories Literature 18 3 Qualified Maintenance Fuel System 18 Fuel Fill and Vent 18 Fuel Filters 3 Special Care Fo
30 Chapter 7: Deck Equipment 45 Chapter 10: Lights 30 Cleats and Tow Eyes 45 Care and Maintenance 30 Ski Tow Ring 45 Navigation Lights 31 Canvas 31 1800MX Convertible Top (If Equipped) 32 1800SR3 & 2000SR3 Convertible Top (If Equipped) 33 2100SC & 2200SR Convertible Top (If Equipped) 34 Side Curtains (If Equipped) 35 1800MX Bimini Top (If Equipped) 36 1800SR3 Bimini Top (If Equipped) 37 2100SC Bimini Top (If Equipped) 38 2000SR3, & 2200SR3 Bimini Top (If Equipped) 38 Bow Cover (If Equipped) 46
Hazard Boxes & Symbols The hazard boxes and symbols shown below are used throughout this Supplement to call attention to potentially dangerous situations which could lead to either personal injury or product damage. Read ALL warnings carefully and follow all safety instructions. ! DANGER! This box alerts you to immediate hazards which WILL cause severe personal injury or death if the warning is ignored.
Chapter 1: Welcome Aboard! This Owner’s Manual Supplement provides specific information about your boat that is not covered in the Sport Boat Owner’s Manual. Please study the Sport Boat Owner’s Manual and this Supplement carefully. Keep the Sport Boat Owner’s Manual and this Supplement on your boat in a secure, yet readily available place. Dealer Service • • • • • Your dealer is your key to service. Ask your dealer to explain all systems before taking delivery of your boat.
Chapter 1: Welcome Aboard! Safety Standards ! DANGER! FALLING and ROTATING PROPELLER HAZARD! NEVER allow anyone to ride on parts of the boat not designed for such use. • Sitting on seat backs, lounging on the forward deck, bow riding, gunwale riding or occupying the transom platform while underway is especially hazardous and will cause personal injury or death.
Chapter 1: Welcome Aboard! Engine & Accessories Literature • The engine and accessories installed on your boat come with their own operation and maintenance manuals. • Read and understand these manuals before using the engine and accessories. • Unless noted otherwise, all engine and accessory literature referred to in this Supplement is included in your owner’s packet.
Chapter 1: Welcome Aboard! Carbon Monoxide (CO) ! DANGER! • Carbon monoxide gas (CO) is colorless, odorless, tasteless, and extremely dangerous. • All engines, generators, and fuel burning appliances produce CO as exhaust. • Prolonged exposure to low concentrations or very quick exposure to high concentrations will cause BRAIN DAMAGE or DEATH. • Teak surfing, dragging, or water skiing within 20 feet of a moving watercraft can be fatal.
Chapter 1: Welcome Aboard! Where and How CO Can Accumulate Stationary Conditions That Increase CO Accumulations Include: A. Using engine, generator, or other fuel burning device when boat is moored in a confined space. B. Mooring too close to another boat that is using its engine, generator, or other fuel burning device. To correct stationary situations A and/or B: • Close all windows, portlights and hatches. • If possible, move your boat away from source of CO.
Chapter 1: Welcome Aboard! Trip Checklist ❏ Make sure you know where the exhaust outlets are located on your boat. ❏ Educate all passengers about the symptoms of CO poisoning and where CO may accumulate. ❏ When docked, or rafted with another boat, be aware of exhaust emissions from the other boat. ❏ Confirm that water flows from the exhaust outlet when the engines and generator are started. ❏ Listen for any change in exhaust sound, which could indicate an exhaust component failure.
Chapter 1: Welcome Aboard! More Information For more information about how you can prevent carbon monoxide poisoning on recreational boats and other ways to boat more safely, contact: United States Coast Guard Office of Boating Safety (G-OPB-3) 2100 Second Street SW Washington, DC 20593 www.uscgboating.org 1-800-368-5647 National Marine Manufacturers Association (NMMA) 200 East Randolph Drive Suite 5100 Chicago, IL 60601-9301 www.nmma.org 312-946-6200 American Boat & Yacht Council, Inc.
Chapter 2: Product Specifications 1800MX Overall Bridge Draft Draft (Drive Length Clearance Beam (Drive Up) Down) 17' 8" 3' 8" 7' 1" 1' 8" Fuel Capacity (gallons) 3' 0" 21 1800SR3 Overall Bridge Draft Draft (Drive Beam Length Clearance (Drive Up) Down) 18' 0" 6' 7" 7' 7" 1' 9" Fuel Capacity (gallons) 3' 1" 28 2000SR3 Overall Bridge Draft Draft (Drive Length Clearance Beam (Drive Up) Down) 20' 4" 6’ 7” 8' 0" 1' 8" Fuel Capacity (gallons) 3' 1" 35 2100SC Overall Bridge Beam Length Clearan
Chapter 3: Locations Exterior Views Hull Views BILGE PUMP DRAIN DECK DRAIN STARBOARD HULLSIDE BOW EYE DASH DRAIN PORT HULLSIDE STORAGE COMPARTMENT DRAIN TRANSOM STERN EYE GARBOARD DRAIN PLUG STERN EYE 9
Chapter 3: Locations 1800MX Deck View WALK-THRU WINDSHIELD GRAB HANDLE BOW LIGHT GRAB HANDLE GRAB HANDLE SKI TOW RING FUEL FILL/VENT DECK FITTING HORN ALL-AROUND LIGHT (REMOVABLE) CLEAT (TYPICAL) BLOWER VENTS BOARDING LADDER 10 GRAB HANDLE
Chapter 3: Locations 1800SR3 Deck View GRAB HANDLES STANDARD SEATING SHOWN BOW LIGHT WALK-THRU WINDSHIELD ALL-AROUND LIGHT (REMOVABLE) HORN CLEAT (TYPICAL) STARBOARD BLOWER VENT (PORT SIDE TYPICAL) FUEL FILL/VENT DECK FITTING SKI TOW RING DRAIN CLEAT BOARDING LADDER GRAB HANDLE 11
Chapter 3: Locations 2000SR3 Deck View WALK-THRU WINDSHIELD BOW LIGHT GRAB HANDLES STANDARD SEATING SHOWN ALL-AROUND LIGHT (REMOVABLE) HORN CLEAT (TYPICAL) STARBOARD BLOWER VENT (PORT SIDE TYPICAL) FUEL FILL/VENT DECK FITTING SKI TOW RING DRAIN BOARDING LADDER 12
Chapter 3: Locations 2100SC Deck View STANDARD SEATING SHOWN BOW HATCH FORWARD DECK GRAB RAILS WALK-THROUGH WINDSHIELD NAVIGATION LIGHTS BOW ROLLER GRAB HANDLES HORN ALL-AROUND LIGHT SOCKET SKI TOW RING CLEAT (TYPICAL) CLEAT BLOWER VENTS FUEL FILL DECK FITTING GRAB HANDLE BOARDING LADDER FUEL TANK VENT DECK FITTING 13
Chapter 3: Locations 2200SR3 Deck View STANDARD SEATING SHOWN WALK-THRU WINDSHIELD NAVIGATION LIGHTS ALL-AROUND LIGHT (REMOVABLE) FUEL FILL/VENT DECK FITTING HORN CLEAT (TYPICAL) FRESHWATER FILL DECK FITTING SKI TOW RING TRANSOM SHOWER CLEAT BOARDING LADDER 14 DRAIN
Chapter 3: Locations Component Locations 12-Volt Accessory Outlet: On the helm console and, if equipped, next to the stereo. Battery: • All models except the 1800MX: On the port side of the engine compartment. • 1800MX: On the starboard side of the engine compartment. Battery Switch (If Equipped): • All models except the 1800MX: Access is through the hatch behind the port jumpseat. • 1800MX: Through the hatch behind the starboard jumpseat. Bilge Pump: In the engine compartment, forward of the engine.
Chapter 4: Propulsion & Related Systems Engine Be sure to read and understand the engine operation and maintenance manuals before starting or doing any maintenance on the engine. Special Starting Instructions for Carbureted Engines (If Equipped) Carbureted engines can be difficult to start when they are cold. In addition to following all instructions and heeding all warnings in the engine manual, try the following: 1.
Chapter 4: Propulsion & Related Systems Engine Compartment Ventilation System ! • • • • WARNING! FIRE/EXPLOSION HAZARD Use of the blower system is NOT A GUARANTEE that explosive fumes have been removed. If you smell fuel, DO NOT start the engine and DO NOT turn on any electrical devices. If you smell fuel and the engine is already running, SHUT OFF the engine and TURN OFF all electrical devices. Investigate immediately. DO NOT obstruct or modify the ventilation system.
Chapter 4: Propulsion & Related Systems Fuel System WARNING! ! FIRE, EXPLOSION AND OPEN FLAME HAZARD! • It is very important that the fuel system be inspected thoroughly the first time it is filled and at each subsequent filling. • The fueling instructions in the Sport Boat Owner’s Manual and the fuel recommendations in the engine operation manual must be followed. ! CAUTION Avoid the storage or handling of gear near the fuel lines, fittings and tank.
Chapter 5: Controls & Gauges Steering • Refer to the engine manual for steering system details. Shift/Throttle Lever ! WARNING! LOSS OF CONTROL HAZARD! Improper maintenance of shift/throttle hardware may cause a sudden loss of control! • Read and understand all of the information about the shift/throttle lever in the Sport Boat Owner’s Manual. • Also, read and understand the shifter/throttle lever manual and the engine manual.
Chapter 5: Controls & Gauges Quick Oil Drain System (If Equipped) QUICK OIL DRAIN SYSTEM TRANSOM OIL DRAIN HOSE OIL DRAIN PLUG ENGINE OIL PAN GARBOARD DRAIN PLUG DRAW CORD BILGE GARBOARD DRAIN To drain the engine oil: 1. 2. 3. 4. 5. 6. 7. 8. Remove the boat from the water. Unscrew the garboard drain plug. Pull the draw cord until the oil drain plug and the oil drain hose slide out of the garboard drain. Place the end of the oil drain hose into a suitable container.
Chapter 5: Controls & Gauges Gauges Cleaning Gauges ! CAUTION PRODUCT or PROPERTY DAMAGE HAZARD! • Use only mild soap and water to clean the gauge lenses and bezels. • Use of other cleaners, including common window cleaning solutions, may cause the lenses to crack. • Lenses cracked in this manner will not be covered by our warranty. Gauge Fogging • Moisture may occasionally find its way into the gauges causing lens fogging. • Turning on the gauge lights will help dry the lenses.
Chapter 6: Plumbing Bilge Pump NOTICE Discharge of oil, oil waste or fuel into navigable waters is prohibited by law. Violators are subject to legal action by the local authorities. • Your boat is equipped with a bilge pump for pumping water out of the bilge. • The bilge pump is controlled by an automatic bilge pump float switch (autofloat switch) and a switch at the helm. • On the 1800MX the bilge pump is only controlled by a switch at the helm.
Chapter 6: Plumbing Bilge Pump Testing • The bilge pump is critical to the safety of your boat. • Check the bilge pump often to make sure it is working. Test the pump as follows: 1. Turn On the bilge pump switch at the helm. 2. Any water in the bilge should pump overboard. • If the pump motor is running, but not pumping, inspect the discharge hose for a kink or collapsed area.
Chapter 6: Plumbing Autofloat Switch (If Equipped) • The automatic bilge pump uses an electromagnetic float switch (autofloat) to turn On the pump whenever water rises above a preset level in the bilge. • The autofloat switch is mounted next to the automatic bilge pump. • The autofloat switch is wired directly to the battery and will normally function even when the boat is completely shut down and left unattended. Test the autofloat switch often as follows: FLOAT SWITCH TESTING 1.
Chapter 6: Plumbing Drain Systems (2100SC Only) Deck Drains • Water on the deck is drained overboard through the deck drains. • Keep the deck drains free of debris. Portable Toilet (2100SC Only, If Equipped) Read the manufacturer’s operating instructions before using the portable toilet. NOTICE Check with local authorities for regulations regarding the legal use of marine head systems.
Chapter 6: Plumbing Portable Head Pump-Out (2100SC Only, If Equipped) Read the manufacturer’s instructions before using the portable head pump-out system.
Chapter 6: Plumbing Freshwater Transom Shower (2200SR3 Only, If Equipped) ! WARNING! • Only use safe drinking (potable) water in your boat’s freshwater system. • Only use a sanitary drinking water hose to fill the water tank or connect to city water. • Never use a common garden hose for drinking water.
Chapter 6: Plumbing • Read the Freshwater System section in the Sport Boat Owner’s Manual. • Your boat is equipped with a pressure type (demand) freshwater (potable) system. • This system is pressurized by turning On the freshwater pump switch. Observe the following about the freshwater system: • Turn the freshwater pump switch Off when the boat is not in use or the water tank is empty. • Inspect and clean the water filter often (located on the water pump).
Chapter 6: Plumbing Freshwater System Winterization ! CAUTION! WATER SYSTEM DAMAGE HAZARD! Never blow compressed air through the water system when all of the faucets are Closed. 1. Turn On the water system switch. 2. Open all of the faucets and showers and let the water system drain completely. 3. Turn Off the water system switch. Any remaining water must be removed from the water lines.
Chapter 7: Deck Equipment Cleats and Tow Eyes ! WARNING! PERSONAL INJURY and /or PRODUCT or PROPERTY DAMAGE HAZARD! • NEVER lift the boat using the bow and stern eyes or the cleats. Carefully read the section on towing in the Sport Boat Owner’s Manual before: • Towing anything behind the boat. • Being towed by another vessel.
Chapter 7: Deck Equipment Canvas ! CAUTION PRODUCT or PROPERTY DAMAGE HAZARD! Take down and securely stow ALL canvas before transporting your boat by road. NOTICE Two people are needed for most of the tasks listed below and on the following pages in this section. 1800MX Convertible Top (If Equipped) D END EYE (TYPICAL) SPRING LOADED SECURING PIN (TYPICAL) HINGE (TYPICAL) C B E A Installing the Convertible Top 1. 2. 3. 4. 5. 6. 7. 8.
Chapter 7: Deck Equipment 1800SR3 & 2000SR3 Convertible Top (If Equipped) E END EYE (TYPICAL) SPRING LOADED SECURING PIN (TYPICAL) HINGE (TYPICAL) F C D A B SWIVEL HINGE SECURING PIN (TYPICAL) Installing the Convertible Top 1. Slide the swivel ends of the main bow (A) over the pre-drilled hole on each side windshield frame (B) and secure with the attached pins. 2. Insert the end eyes of the aft braces (C) into the deck hinges and secure them with the spring-loaded pins. 3.
Chapter 7: Deck Equipment 2100SC & 2200SR Convertible Top (If Equipped) NOTE: 2100SC TOP PICTURED. 2200SR TOP SIMILAR. E B A G C D F SWIVEL END SECURING PIN Installing the Convertible Top 1. Slide the swivel ends of the main bow (A) over the pre-drilled hole on each side windshield frame (B) and secure with the attached pins. 2. Hook the hold down straps (C) into the deck loops (D). 3. Unfold the canvas top and pull the secondary bow (E) and the canvas forward. 4.
Chapter 7: Deck Equipment Side Curtains (If Equipped) A Installing the Side Curtains 1. Snap the forward corner (A) of each side curtain to the windshield frame. 2. Work your way aft, alternately snapping the top and bottom snaps.
Chapter 7: Deck Equipment 1800MX Bimini Top (If Equipped) END EYE (TYPICAL) SPRING LOADED SECURING PIN (TYPICAL) HINGE (TYPICAL) A E F G B C D Installing the Bimini Top 1. Insert the end eyes of the main bow (A) into the deck hinges (B) located next to the aft ends of the windshield frames and secure them with the pins. 2. Insert the end eyes of the aft braces (C) into the aft deck hinges (D) and secure them with the pins. 3.
Chapter 7: Deck Equipment 1800SR3 Bimini Top (If Equipped) SWIVEL END END EYE (TYPICAL) SPRING LOADED SECURING PIN (TYPICAL) SECURING PIN HINGE (TYPICAL) A C B D Installing the Bimini Top 1. Slide the swivel ends of the main bow (A) over the holes in the side windshield frames and insert the securing pins. 2. Insert the end eyes of the aft braces (B) into the aft deck hinges and secure them with the spring loaded pins. 3.
Chapter 7: Deck Equipment 2100SC Bimini Top (If Equipped) SWIVEL END A SECURING PIN E F C B G H D Installing the Bimini Top 1. Slide the swivel ends of the main bow (A) over the aft holes (B) in the side windshield frames and insert the securing pins. 2. Hook the aft strap (C) into the deck loops (D). 3. Unfold the canvas and slide the swivel ends of the forward braces (E) over the forward holes (F) in the side windshield frames and insert the securing pins. 4.
Chapter 7: Deck Equipment 2000SR3, & 2200SR3 Bimini Top (If Equipped) SWIVEL END END EYE (TYPICAL) SPRING LOADED SECURING PIN (TYPICAL) SECURING PIN HINGE (TYPICAL) A D E B C F Installing the Bimini Top 1. Slide the swivel ends of the main bow (A) over the aft holes (B) in the side windshield frames and insert the securing pins. 2. Insert the end eyes of the aft braces (C) into the deck hinges and secure them with the spring loaded securing pins. 3.
Chapter 8: Entertainment Systems Audio System NOTICE AM radio reception may be impaired anytime the engine is running. Read and understand the instruction manual for your boat’s audio system before using.
Chapter 9: Convertible Seats, Beds, & Tables Sleeper Seats (If Equipped) • The sleeper seats can be moved forward and aft while in the upright, operating position. • The sleeper seats can also be converted into a flat lounge or chaise lounge. Operating Positions To slide the seat forward and backward: OPERATING POSITIONS 1. Pull up on the forward seat slider lever (A) and slide the seats forward or aft to the desired position.
Chapter 9: Convertible Seats, Beds, & Tables Cuddy Cabin to V-Berth Conversion (2100SC Only) 1. Place the forward filler cushion (A) over the portable toilet (B). 2. Remove the aft cushions (C). A C B 3. Lift the forward outboard cushions (D) and slide the filler boards (E) aft. D D E 4. Align the velcro strips (F) on the underside of the filler boards with the velcro tabs (G) on the aft support lip.
Chapter 9: Convertible Seats, Beds, & Tables 5. Place the aft cushions (C), that were removed in step two, on top of the filler boards. 6. Insert the remaining center filler cushions (H).
Chapter 9: Convertible Seats, Beds, & Tables Jump Seat to Sunlounge Conversion (If Equipped) ! DANGER! PERSONAL SAFETY HAZARD! DO NOT allow anyone to ride the aft sunlounge cushions while underway or anytime the engine is running. C A A C B A C D 1. 2. 3. 4. Remove the jump seats (A) by lifting and pulling on their forward edges. Rotate each jump seat so that the lounge support tabs (B) face the support slots (C). Slide the lounge support tabs into the support slots.
Chapter 9: Convertible Seats, Beds, & Tables Engine Cover to Sunlounge Conversion (If Equipped) ! CAUTION PRODUCT DAMAGE HAZARD! • Damage to the upholstery will occur if the motor cover is opened while it is in the upright or chaise lounge position. 1. Pull up on the port aft corner loop (A). 2. Place the plastic support (B) securely in the first notch (C) for an upright position or in the second notch (D) for a chaise lounge position.
Chapter 10: Lights Care and Maintenance All of the lights installed on your boat are of top quality, but you should be aware that failure may periodically occur for a variety of reasons: 1. 2. 3. 4. There may be a blown fuse - replace the fuse. The bulb may be burned out - carry spare bulbs for replacement. A wire may be damaged or may have come loose - repair as required. The bulb base may be corroded - clean the base and coat it with non-conductive electrical lubricant.
Chapter 11: Electrical System ! • • • • DANGER! EXTREME FIRE, SHOCK & EXPLOSION HAZARD! To minimize the risks of fire and explosion, NEVER install knife switches or other arcing devices in the fuel compartments. NEVER substitute automotive parts for marine parts. Electrical, ignition and fuel system parts were designed and manufactured to comply with rules and regulations that minimize risks of fire and explosion. DO NOT modify the electrical systems or relevant drawings.
Chapter 11: Electrical System 12-Volt DC System Battery The battery supplies electricity for lights, accessories, and engine starting. The Electrical section of Chapter 8 in the Sport Boat Owner’s Manual, provides battery, care and maintenance instructions. Fuses and Circuit Breakers • Fuses for the engine and main accessory power are on the fuse block behind the dash. • Some equipment may have secondary fuse protection at the unit, or at the battery. • Electronics power is provided at the helm station.
Chapter 11: Electrical System Electrical Routings 1800MX Deck Electrical Harness NOTE: VIEW IS OF UNDERSIDE OF DECK DASH HARNESS BOW LIGHT 12 VOLT RECEPTACLE HORN STEREO FUSE BLOCK SHIFTER & KILL SWITCH SPEAKER SPEAKER ENGINE PLUG & SPEEDOMETER PICKUP BILGE PUMP FUEL FILL GROUND ALL-AROUND LIGHT TRIM PUMP BATTERY BLOWER 48
Chapter 11: Electrical System 1800SR3 and 2000SR3 Deck Electrical Harness NOTE: VIEW IS UNDERSIDE OF DECK BOW LIGHT HORN FUSE PANEL STEREO SPEAKER DASH HARNESS SPEAKER SHIFTER & KILL SWITCH ENGINE PLUG & SPEEDOMETER PICKUP BILGE PUMP AND BLOWER HARNESS TRIM PUMP BUSS BAR BATTERY FUEL FILL GROUND ALL-AROUND LIGHT 49
Chapter 11: Electrical System 2100SC Deck Electrical Harness NOTE: VIEW IS UNDERSIDE OF DECK BOW LIGHTS CABIN LIGHTS CO MONITOR SPEAKER GAUGE PANEL DASH HARNESS FUSE PANEL SWITCH PANEL COURTESY LIGHTS SPEAKER SHIFTER & KILL SWITCH TRANSDUCER COURTESY LIGHT ENGINE PLUG & SPEEDOMETER PICKUP BILGE HARNESS BLOWER BATTERY FUEL FILL GROUND ALL-AROUND LIGHT 50
Chapter 11: Electrical System 2200SR3 Deck Electrical Harness NOTE: VIEW IS UNDERSIDE OF DECK STARBOARD NAVIGATION LIGHT SPEAKERS PORT NAVIGATION LIGHT COURTESY LIGHT CABIN LIGHT HORN STEREO 12 VOLT RECEPTACLE DASH HARNESS SPEAKER FUSE BLOCK SHIFTER & KILL SWITCH TRIM PUMP & BLOWER ENGINE HARNESS SPEAKER ENGINE PLUG & SPEEDOMETER PICKUP ALL-AROUND LIGHT BATTERY WATER PUMP COURTESY LIGHT FUEL FILL GROUND 51
Chapter 11: Electrical System Wiring Diagrams 1800MX 52
Chapter 11: Electrical System 1800SR3 & 2000SR3 53
Chapter 11: Electrical System 2100SC 54
Chapter 11: Electrical System 2200SR3 55
Important Records Selling Dealer Key Numbers Name Of Dealership Ignition Other Address Electronics Phone/FAX/E-mail Manufacturer Model Name/Number Sales Manager Serial Number Service Manager Manufacturer Model Name/Number Engine Serial Number Manufacturer Model Name/Number Engine Serial Number Oil Type/SAE Quarts per Engine Manufacturer Filter Type Propeller Model Name/Number Serial Number Manufacturer Model Name/Number Serial Number Manufacturer Pitch Model Number 56
Float Plan Before going boating, fill out a copy of this float plan (or similar) and leave it with a reliable person whom you can depend on to contact the Coast Guard or other rescue organization, if you do not return as scheduled.
Float Plan Survival Equipment Trip Expectations Marine Radio (Yes/No) Type Frequencies Number of PFDs Flares (Yes/No) Mirror (yes or no) Smoke Signals (Yes/No) Flashlight (Yes/No) Food (Yes/No) Departing From Departure Date Departure Time Stopover 1 Water (Yes/No) Anchor (Yes/No) Raft/Dinghy (Yes/No) Arrive No Later Than: Date Paddles (Yes/No) EPIRB (Yes/No) Other Other Other Other Arrive No Later Than: Time Stopover 2 Arrive No Later Than: Date Arrive No Later Than: Time Vehicle
Owner’s Notes
Owner’s Notes
