Installation and Operation Guide For MCF-49FD, MCF-23FD MCR-49FD, MCR-23FD
CONTENTS 1. SPECIFICATIONS 2 2. SERIAL NUMBER 2 3. INSTALLATION 3 4. CLEANING 4 5. CAUTION 4 6. BASIC OPERATION 6-1. REFRIGERATOR 6-2. FREEZER 5-6 7-8 7. REVERSIBLE DOOR ASSEMBLING METHOD 9 -10 8. TROUBLE SHOOTING GUIDE 11 SPECIFICATIONS Solid Door Refrigerators MODEL COMP. H.P REFRIGERANT AMPERAGE POUNDS MCR-23FD 1/3 R-134a 420W 271 MCR-49FD 1/2 R-134a 570W 370 MODEL COMP. H.
INSTALLATION 1. GOOD AIR CIRCULATION - Be sure to avoid any object which will restrict exhausted air flow. - Be sure that there is ample space so that air can flow through the rear of the unit. - The back of the unit should be located no less than 5 inches from the wall. 2. PLACE ON STRONG GROUND - Be sure the location chosen has a floor strong enough to support the total weight of the cabinet and contents. 3.
CLEANING 1. CLEANING THE INTERIOR AND EXTERIOR - The interior and exterior of the unit can be cleaned using warm water with soap. - Do not use an abrasive cleaner because it will scratch the surface. 2. CLEANING THE CONDENSER FINS - To maintain proper refrigeration performance, the Condenser coil must be free of dust, dirt, and grease. It will require to clean it periodically. Condenser fins should be cleaned, at least every three months (90 days) or as needed. 3.
BASIC OPERATION MCR-23FD MCR-49FD REFRIGERATOR 1. Plug in and turn on the power switch located on the bottom of the top grill. The Display panel will be lighted. The compressor will begin to run. 2. The default temperature setting is 35ᵻ (+1ᴱ) 3. The compressor is automatically cycled by the electronic controller (PCB). 4. Temp. Control range 39ᵻ @28ᵻ ( +7ᴱ @-3ᴱ) 5. The interior light is activated by the door switch when the door is opened. 6.
DISPLAY PANEL DOOR OPENING INSIDE TEMP. TEMP. CONTROL BUTTON 1. UP / DOWN BUTTON (Temperature control button) - By pushing the up/down button, you can set the inside temperature. 2. DOOR OPENING INDICATOR - If door is opened, door opening indicator will be turned on. - If the door is left open for 5 minutes an alarm will sound continuously. - The alarm will stop immediately upon closing the door.
BASIC OPERATION MCF-23FD MCF-49FD FREEZER 1. Plug in and turn on the power switch located on the bottom of the top grill. The Display panel will be lighted. The compressor will begin to run. 2. The default temperature setting is -2ᵻ (-18ᴱ) 3. The compressor is automatically cycled by the electronic controller (PCB, D-sensor). 4. The Defrost cycle is automatically controlled by the D-sensor and the PCB. 5. Temp. Control range 5ᵻ @-9ᵻ (-3ᴱ @-24ᴱ) 6.
DISPLAY PANEL DOOR OPENING INSIDE TEMP. TEMP. CONTROL BUTTON 1. UP / DOWN BUTTON (Temperature control button) - By pushing the up/down button, you can set the inside temperature. 2. DEFROST - The electronic defrost controller is set at the factory to provide a defrost cycle every 6 hours. - Once all frost is eliminated, the defrost control is changed to the freezer mode. - The panel displays " " during the defrost. 3. DOOR OPENING INDICATOR - If door is opened, door opening indicator will be turned on.
REVERSIBLE-DOOR ASSEMBLY METHOD MODEL : MCF-23FD / MCR-23FD 1. REMOVAL OF TOP GRILL and GRILL ASSEMBLY 1) Remove the TOP GRILL by ῡ removing securing screws. Upper or downward located ῡ in the PICTURE (A) TOP GRILL 2) Remove GRILL by removing securing screws. connected Left and right side located ῢ ῢ GRILL ASSEMBLY in the PICTURE (A) # Caution : Disconnect power before reversing door, use caution with PICTURE A cares associated with electronic control. 2.
3. Installation method of REVERSIBLE DOOR 1) After reversing 180 degree DOOR ASSEMBLY ῦ, locate the HANDLE in the desired side. Ῡ M5*27 SCREW ΰ DOOR-HINGE 2) Assemble in the following LOWER order.
TROUBLE SHOOTING GUIDE SYMPTOMS Refrigerator/Freezer is freezing (thawing) food. The unit does not refrigerate at all. The unit does not refrigerate well. There is a loud noise. There is condensation in the unit exterior. There is condensation the unit interior. The door does not close tightly. CAUSES SOLUTIONS The Temp. is set too low (high) to maintain food freshness. Push the button to a warmer (colder) position. There is a power connection failure problem.
MEMO
MEMO
MEMO
SSUU@e @a N@s @QVP fN@l L@fl@SSSSQ t Z@HYUTI@RPRMWTQY fZ@HYUTI@RPRMWSSW N N ᶉ warranty@and@technical@service w@@s @p t@ Z@QMXXXMTVTMwasp fZ@TQTMWWTMRTQP RT@@@L@W@@@ @@@@@@@@@@@@@@@@@@@@@@