AUT OMAT I C I CECUBEMACHI NE Us er ’ sManual Model s :MI M75/ MI M100/ MI M130 * Bes ur et hei cemachi nehasbeens t andi ngupr i ghtf oratl eas t24hour spr i ort opl ugi n.
TABLE OF CONTENTS Page ICE MAKER SAFETY............................................................................................................... ...........2 IMPORTANT SAFEGUARDS..........................................................................................................3-5 TECHNICAL INFORMATION............................................................................................................5 INTRODUCTION...........................................................................
ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the Safety Alert Symbol. This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the Safety Alert Symbol and either the words "DANGER", "WARNING" or "CAUTION".
IMPORTANT SAFEGUARDS Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manual carefully. To reduce the risk of fire, electrical shock or injury when using the ice maker, follow basic precautions, including the following: Plug into a grounded 3-prong outlet; do not remove grounding prong, do not use an adapter, and do not use an extension cord.
Code and local codes and ordinances is required. Do not kink or pinch the power supply cord between the ice maker and cabinet. The circuit breaker rating should be 15 amperes. It is important for the ice maker to be leveled in order to work properly. You may need to make several adjustments to level it. All installations must be in accordance with local plumbing code requirements. Make certain that the pipes are not pinched or kinked or damaged during installation.
receptical. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the ice maker, be careful not to damage the power cord. Extension Cord DO NOT use an extention cord with this appliance. TECHNICAL INFORMATION Model: MIM75 Rated power: 120VAC~60Hz Ice-making rated current: 6.7A Ice-harvest rated current: 11.2A Refrigerant: R134a 6.88oz 195.
INTRODUCTION The Maxx Ice MIM series Ice Maker finds wide application in households, bars, restaurants, hotels, supermarkets, etc. It produces crystal-clear, gourmet cube ice, and offers convenience for homeowners and hotel guests. An insulated ice storage bin is built into the ice maker. This user's manual is intended as a resource for persons installing, using and servicing the MIM series. It contains valuable information on safety and maintenance.
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic precautions: Replace all panels before Plug into a grounded 3-prong outlet. operating. Do not remove grounding prong. Use two or more people to move Do not use an adapter. and install ice maker. Do not use an extension cord. Disconnect power before cleaning. Disconnect power before servicing.
ICE ICE MAKER INSTALLATION Unpacking Excessive Weight Hazard Use two or more people to move and install ice maker. do so can result in back or other serious injury. Failure to Remove packaging materials NOTE: Do not remove any permanent instruction labels or the data label on your ice maker. Remove tape and glue from your ice maker before using. To remove any remaining tape or glue, rub the area briskly with your thumb.
Location Requirements 4” To ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. Allow at least 4” (101mm) clearance at rear, and 0.6” (15mm) at the top and sides for proper air circulation. The installation should allow the ice maker to be pulled forward for servicing if necessary. When installing the ice maker under a counter, follow the recommended spacing dimensions shown.
Normal operating ambient temperature should be between 55℉ (13℃) to 90 ℉ (32℃). Normal operating water temperature should be between 41℉ (5℃) and 77℉ (25℃). Operation of the icemaker for extended periods out side of these normal temperature ranges may affect production capacity. In general, it is always a good idea to filter the water. A water filter, if it is of the proper type, can remove taste and odors as well as particles.
completely unobstructed. Allow at least 4” (101mm) clearance at rear, and 0.6” (15mm) at the top and sides for proper air circulation. The installation should allow the ice maker to be pulled forward for servicing if necessary. When installing the ice maker under a counter, follow the recommended spacing dimensions shown. Place electrical and water supplies and drain fixtures in the recommended locations as shown. NOTE: Do not kink or pinch the power supply cord between the ice maker and cabinet.
equipped with a power supply cord having a NEMA 5-15P 3-prong grounded plug. To minimize possible shock hazard, the cord must be plugged into a mating NEMA 5-15R 3-pronged, wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a NEMA 5-15R wall receptacle installed by a qualified electrician.
outlet directly behind the ice maker will make under-counter installation easier. NOTE: 1. All installations must be in accordance with local plumbing code requirements. Professional installation is recommended. 2. Make certain that the pipes are not pinched or kinked or damaged during installation. 3. Check for leaks after connection. Tools required: ½” (13mm) open-end wrench Phillips style screwdriver Connecting the water line: 1. Turn off main water supply.
1. Find the floor drain near the ice maker. The distance should be less than 10 feet (3.5M) as the length of the long drain water pipe provided with the ice maker is about 10 feet (3.5M). 2. All horizontal runs of drain lines must have a fall of ¼″ per foot (6.35mm per 30.5cm). An air gap will likely be required between the ice maker drain tube and the drain/waste receptacle. A stand pipe with a trap below it would be acceptable for the drain/waste receptacle. A floor drain is also acceptable. 3.
Installation Types This ice maker has been designed for Mobile (free-standing), Enclosed, or Built-in (sealed) installation. Mobile installation: A mobile installation will allow you to install the icemaker free-standing in any place you desire provided you have access to a water supply and drainage facilities. You must follow the stated instructions for a- Electrical requirements b- Water supply and drain connections c- Leveling the icemaker.
5. 6. 7. 8. drain connections and the nut of the drain water hole. Tighten any connections or fittings that leak. If electrical outlet for the ice maker is behind the cabinet, plug in the ice maker. Push the ice maker into position. Pour 1 gallon (3.79L) of water to the ice storage bin to check if the drainpipe is kinked or pinched. Seal all around the cabinet to the floor with an approved caulking compound. OPERATION Final Check List before Operation 1.
Operating Method 1. Switch on the Power switch on the front panel. The light will be on. The ice maker will start working automatically and feeding water. 2. After the first feeding of the water, the machine will automatically go to the ice making stage, and the sound of water spraying will be heard. 3. Ice will be harvested to the ice storage bin. When the storage bin is filled with ice cubes, the ice maker will automatically stop working.
hot gas valve and water inlet valve open to warm up the freezing surface, allowing the cubes to fall into the bin. Once completed, the freeze cycle begins repeatedly until the ice has satisfied the maximum level in the bin, then the water and compressor are shut down until sufficient ice is drawn below the bin level sensor and the cycle again resumes. How the machine uses water The ice maker begins with a fixed charge of water that is contained in the water bin.
The high-efficiency compressor may make a pulsating or high-pitched sound. Water running from the water bin to the evaporator plate may make a splashing sound. Water running from the evaporator to the water bin may make a splashing sound. As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing through your icemaker. You may hear air being forced over the condenser by the condenser fan.
Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, or the unit is used outdoors, or there are other special considerations. What shouldn't be done? Never keep anything in the ice storage bin that is not ice: objects like wine and beer bottles are not only unsanitary, but the labels may slip off and plug up the drain.
Commercial grades of stainless steel are susceptible to rusting if not properly maintained. It is important that you properly care for the stainless steel surfaces of your ice machine and bin to avoid the possibility of rust or corrosion. Use the following recommended guidelines for keeping your stainless steel looking like new: 1. Clean the stainless steel thoroughly once a week. Clean frequently to avoid build-up of hard, stubborn stains.
Condenser Cleaning A dirty or clogged condenser prevents proper airflow, reduces ice making capacity, and causes higher than recommended operating temperatures that may lead to component failure. Have the condenser cleaned at least once every three months. 1. Unplug the ice maker or disconnect power. 2. Unscrew the screws on the front cover. 3. Grasp the underpart of the right and left side, rise a little, and then pull down.
DO NOT use solvent-based cleaning agents or abrasives on the interior. These cleaners may transmit taste to the ice cubes, or damage or discolor the interior. SPRINKLER HEAD CLEANING NOTE: The sprinkler should only be cleaned when you find that some of the ice cubes are improperly shaped during ice making. Cleaning the ice making system should follow cleaning of the sprinkler. 1. Disconnect power to the unit and open the door. 2. Take out the row of flake covers. 3. Find the sprinkler and the slideway.
4. Find which water sector is not spraying correctly from the nozzle. If the slideway is the issue, adjust the position of slideway to have all the water sectors free forward to the ice mold. If the water sectors are free, but some sectors is not spraying properly, using a new tooth-brush, clean the gap of the nozzle several times. The water sector should work normally. 5. Another cleaning method; remove the slideway from the water bin. 6. Find the sprinkler arm and raise it.
10. Reassembly the sprinkler arm, slideway and the flake covers. 11. After the Icemaker System Cleaning procedure below. Ice Making System Cleaning Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 15 to 20 grains/gal.
6. Allow 30 minutes for proper cleaning. After cleaning, shut off the power switch, and unscrew the nut of the water-draining hole. Drain off the waste water to some container, and then screw the nut on tightly when the waste water is fully drained off. 7. Inspect the evaporator and water spillway to ensure all mineral residue has been removed. If necessary, wipe the evaporator, spillway and other water transport surfaces with a clean soft cloth to remove any remaining residue.
1. Prepare a sanitizing solution made of 1oz (29ml) of household bleach and 2 gallons (7.5L) of hot water 95ºF (35°C) to 115ºF (46°C). Remove the flake covers and slideway from the water bin and wipe the entire bin inside and out, covering all surfaces. 2. Fill a spray bottle with the sanitizing solution and spray all corners and edges making sure to cover all surfaces with the solution. Soak the flake cover and slideway in the solution and put back in place after drying. 3.
longer. Turn the knob counter-clockwise, and the ice size will be smaller in the next cycle. NOTE: It is not a good idea to adjust the ice size often or for no good reason, because the controller may damaged. 7. If the red, green and yellow LEDs are flashing together, the machine is not working. Call for service. NOTE: Avoid letting water contact the control box. Major Functions 1. Completely automatic operating procedure. 2.
Red LED Clean Ice full Ice size adjust Green LED Ice making Yellow LED Mode Ice harvest Control box (behind Front Cover) TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the OPERATION section of this manual first. If the problem persists, check the TROUBLESHOOTING GUIDE on the following pages. The problem could be something very simple which can be solved without a service call.
Troubleshooting Guide Problem Possible Cause Probable Correction The ice maker is unplugged. The fuse is blown. The machine doesn’t operate The water doesn't feed in after the ice maker starts. Machine makes ice, but bin does not fill up with ice The ice maker power switch is OFF. The voltage of the power supply is low. Ice cube full sensor damage The ice storage bin is full of ice. The water supply tap is turned off. Water supply pressure is lower.
Water is leaking from the unit. The body of the ice maker is electrified. Scales occur frequently inside the machine. The ice cubes are incomplete when being dumped. Cubes are partially formed or are white at the bottom. Noise during operation The downcomer doesn't leak. Harvesting ice is difficult The power indicated lamp is light,but the machine don't operate A few water drops fall to the floor when you open the door to take out ice from ice storage bin. Water supply connection leaking.
The electricity is off. The room temperature is out of the stated range. The ice maker stops suddenly while making ice. Cubes are too big. The fuse is brown. The voltage of the power supply is low. The ventilation louvers are covered. The ambient temperature and water temperature is too low. 31 Reconnect the power supply line. Cut off the electricity; let the ice maker stop working till the temperature returns within the stated range. Replace fuse. Add manostat. Remove the obstruction.
Tested and certified to NSF standard 12 by NSF International 32
MAXXI CE 3355Ent er pr i s eAvenue,Sui t e160Wes t on,F l or i da33331 T el :9542027419 -F ax:9542027337
