Instructions / Assembly

Electrical parameters:
Installation Guide:
1. Turn off the power before installation. Remove the
existing fixture if applicable.
2. Determine the location for installation and cut
ceiling hole with an approximate diameter of 6.25"
or 158mm. (Fig. 1)
3. Open the DRIVER/JUNCTION BOX cover and
remove the appropriate knockout(s) on the side
panel. (Fig. 2)
4. Insert the electrical supply cable through the
knockout and connect the ground wire to the green
wire terminal, hot wire to the black wire terminal and
neutral wire to the white wire terminal using the
wire nuts provided.
Model
Driver/Junction Box
Input Voltage (V)
Input Frequency
(Hz)
Input Current (A)
Input Watts (W)
MRL-S61200W, MRL-S61200NW
120
60
0.10
12
6" Round Slim LED Flat Panel Installation Instructions
The units covered in these instructions are intended to retrofit Type IC or Type Non-IC luminaires.
WARNING / ATTENTION
1.
Risk of fire. Supply conductors (power wires) connecting to the fixture must be rated 90°C.
If
uncertain
consult an electrician.
2. Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical
systems.
3. Risk of fire or electric shock. If not qualified, do not attempt installation. Contact a qualified
electrician.
4. Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features
and dimensions shown in the photographs and/or drawings.
5. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp
objects.
6. This lamp is not intended for use with emergency exit fixtures or emergency lights.
CAUTIONS
NOTES
1. For your safety read and understand instructions completely before starting installation.
2. Before attempting Installation, check your local electric code, as it sets wiring standards for
your locality.
1. If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is
connected to the switch. DO NOT connect the white supply wire to the switch.
2. Make sure no bare wires are exposed outside the wire nut connectors.
3. Do not make or alter any open holes in an enclosure of wiring or electrical components during
kits installation.
www.maxximastyle.com
Approved Dimmers
Leviton: 6672, 6674
Lutron: S-600P, SLV-600P, CN-600P, DVWCL153P,
CTCL-153P,
CTCL-153PR, DVCL-153PR, DVCL-253P
Maxxima: MEW-DM600, MEW-DM620, MEW-DM650
Five Year Warranty:
Maxxima extends a 5 year limited warranty to the original purchase that the products listed are free from defects in
material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/
purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty
period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This
offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation
whatsoever beyond sending a free replacement product.
Luminous Intensity Distribution Diagram
Hole Diameter: 6.25" (158mm)
5. Place all wiring and connections back into the
box and close the cover. Connect the DRIVER/
JUNCTION BOX to the light panel using the
CONNECTOR.
6. Insert DRIVER/JUNCTION BOX through the
mounting hole (Fig. 3) and secure using mounting
tabs.
7. Push the SPRING-LOADED CLIPS into the
mounting hole upwards and insert LIGHT PANEL
into it. Release the clips and the fixture will be
pulled flush to the ceiling. (Fig. 4)
SPRING-LOADED CLIPS
CONNECTOR
DRIVER/JUNCTION BOX
LIGHT PANEL
Parts List
Hole Cutout Diameter
The Hole Cutout Diameter size is 6.25" or 158mm