SUPER SPORT AMPLIFIERS Autotek is proud to introduce the finest high end car audio products available and would like to thank you for your continued support. The Super Sport Series products have been designed to a very high level of performance, with features unavailable in any other products.
GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion.
AMPLIFIER FEATURE DESCRIPTIONS SUPER SPORT AMPLIFIERS: ! Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except the mono amps which are capable of 4, 2 and 1-Ohm loads. ! Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable amplifiers. ! The input sensitivities for rated output powers are variable from 0.2 volt to 5 volt. ! All crossovers are fully variable in their respective ranges. ! Crossover filters are 12dB/Octave.
AMPLIFIER FEATURE DESCRIPTIONS SUPER SPORT AMPLIFIERS: SS1000.1D / SS1500.1D 1-CHANNEL MONO AMPLIFIERS LINE INPUT: Accepts unbalanced RCA inputs from 0.2 volts to 9 volts. LINE OUTPUT: The unbalanced RCA outputs are set the same as the CROSSOVER switch on he top mount control. BALANCED INPUT: Accepts balanced line inputs from 0.4 volts to 12 volts for the optional MMBLD-1 balanced line driver.
SS75.2 / SS125.2 / 2 CHANNEL AMPLIFIER APPLICATIONS FULL RANGE STEREO This is the most basic application for the SUPER SPORT Series 2 channel amplifiers. 1. Interconnect cable checklist: Connect the LINE INPUTS to the Radio/CD with good quality RCA cables. 2. Crossover Switch: The X-OVER switch must be in the FULL position. 3. Crossover frequency control checklist: N/A for full range operation. 4. Line Level: Refer to the section “Setting up systems after installation for best performance”.
SS75.2 / SS125.2 2-CHANNEL AMPLIFIER APPLICATIONS Stereo high pass with mono low-pass in a 2 way active, or bi-amplified system In this application we will use a 2 channel amplifier for the high frequencies, and a second one for the low frequencies, or mono sub bass. Please consult the speaker specifications to determine maximum amplifier power requirements. Interconnect cable checklist: Connect the inputs of the HIGHS amplifier to a Radio/CD with good quality RCA cables.
SS75.4 / SS125.4 / 4 CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straight forward discrete 4 channel full range units. Level control checklist: - Refer to the section “Setting up systems after installation for best performance” Interconnect cable checklist: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. Minimum final loudspeaker impedances: - 2-Ohms per channel.
SS75.4 / SS125.4 / 4 CHANNEL AMPLIFIER APPLICATIONS 2 way active, or bi-amplified system with mono bass This application shows how easily a 2 way active system can be implemented using a 4 channel amplifier. Channels 1 and 2 will be used for highs, and channels 3 and 4 for mono bass. Interconnect cable checklist: - We need to feed the same signal to both sets of channels, so must use 2 Yadapters, one to feed the LEFT signal to channels 1 and 3, and the right signal to channels 2 and 4, as shown.
SS500.1 / SS7500.1 / MONO AMPLIFIER APPLICATIONS Basic application These sub bass amplifiers can be used in any of the bi-amplification systems described in this manual, replacing the 2 channel amplifiers as per the illustrations. SUBSONIC:15 Hz to 35 Hz BASS EQ: 0 to +12dB PHASE: 0 to 180 degrees Interconnect cable checklist: Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables. Connect the LINE OUT to the inputs of the system highs amplifier.
SS1000.1D / SS1500.1D / MONO AMPLIFIER APPLICATIONS Basic application These sub bass amplifiers can be used in any of the bi-amplification systems described in this manual, replacing the 2 channel amplifiers as per the illustrations. SUBSONIC:15 Hz to 35 Hz BASS EQ: 0 to +12dB PHASE: 0 to 180 degrees Interconnect cable checklist: Connect the inputs to a suitable source, e.g. a head unit with good quality RCA cables. Connect the LINE OUT to the inputs of the system highs amplifier.
SS1900.1D MONO AMPLIFIER APPLICATIONS BASIC APPLICATION The 1 channel mono amplifiers are capable of 4, 2 & 1 Ohms loads and can be used in any of the “bi-amplifier” systems described in the full range amplifier directions. SINGLE AMP INSTALLATION PROCEDURE: 1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out puts with good quality RCA interconnect cables. 2.
0 autotek SUPER SPORT SERIES AMPLIFIER FEATURES 11
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE SS75.2 / SS125.2 / SS75.4 / SS125.4 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a great starting point.
TROUBLESHOOTING A SYSTEM The key to finding the problem in a misbehaving sound system is to isolate parts of that system in a logical fashion to track down the fault. Description of the PROTECT system built into all Autotek amplifiers The diagnostic system will shut down the amplifier, until reset by turning the head unit off, and back on. This state of affairs will be indicated by the front panel PROTECT LED lighting up under the following conditions: 1 - A sort circuit on the loudspeaker leads.
autotek SUPER SPORT AMPLIFIERS Maxxsonics Limited Warranty As the manufacturer of Maxxsonics, Autotek, Crunch, MB Quart and Hifonics car audio products, Maxxsonics USA Inc. Warrants to the original consumer purchaser the amplifier to be free from defects in material and workmanship for one (1) Year from date of purchase. All other parts and accessories of the system are warrantied to be free from defects in material and workmanship for one (1) year from date of purchase.
