Maxxus Infrared Sauna Instruction Manual Models MX-K206-01 / MX-K306-01 / MX-K406-01 FOR CARBON MODEL SAUNAS HEMLOCK AND RED CEDAR MODELS FOR INDOOR USE ONLY 120V/15AMP DEDICATED CIRCUIT REQUIRED FOR MX-K206-01 120V/20AMP DEDICATED CIRCUIT REQUIRED FOR MX-K306-01 & MX-K406-01
Thank you for choosing Maxxus Infrared Sauna! Index ===================================== Page Important Safety Guides…………………………………………………...… 2 Introduction…………………………………………………………...………… 3 Health & Beauty Benefits……………………………………………………… 3 Highlights……………………………………………………………….……..… 4 Assembly..…………………………………….……………………………..….. 4 Sauna Operation…...…………………………………………………………… 11 Warnings…………………………………………………………………………. 13 Troubleshooting…………………………………………………………………. 13 Maintenance………………………………………………………………..
READ IMPORTANT SAFETY GUIDES BEFORE USING! READ AND FOLLOW ALL INSTRUCTIONS A). Please following all warning labels and markings on the sauna room. B). Do not install any receptacles on the interior or exterior walls of the sauna room. C). No locking devices are installed or shall be installed on the door of the sauna room which could result in entrapment within the sauna room. D). During use, the ceiling vent can be in the opened position. E).
M). Never sleep inside the sauna. N). Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with a cloth and water. O). Do not stack or store any object on top or inside the sauna. P). Do not use the sauna during an electrical storm to avoid risk of shock. Q). Do not attempt to make any repairs yourself. If a problem occurs with the sauna, please contact seller, distributor, or the manufacturer to avoid safety risks.
Highlights a. High quality craftsmanship b. Automatic thermostat for constant temperature c. Timer and buzzer: buzzer sounds 5 minutes before the end of the sauna session d. Digital sensor and thermometer e. Infrared carbon heat emitter panels f. Wiring diagram: Assembly Assembly Requirements a. You will need a philips screwdriver, ladder, and two adults to assemble. b. Do not plug any other appliances into the power supply of the sauna room other than the designated sauna connections/plugs. c.
1 1-----Roof Cover 5 2---- Roof Panel 2 3----Left Side Panel 6 3 4----Front Panel 5----Back Panel 4 6----Right Side Panel 7----Bench 7 8----Bench Heater Board 9----Floor Heater 8 9 FIG-1 3. 2-person sauna is packed into two cartons. For example: C/NO: 002 3-person sauna and 4-person saunas are packed in three cartons. 002 2 OF 3, and C/NO: 002 FIG-2.1 4. 1 OF 2 and C/NO: 002 For example: C/NO: 002 1 OF 3, 2 OF 2. C/NO: 3 OF 3. See FIG-2.1 & 2.2 Cartons FIG-2.2 C/No.
FIG 3 5. Placing Floor Panel FIG 4 Assembling Back Panel Align the Back Panel with the Floor Panel’s corresponding wood pattern; make sure the wood pattern is flowing in the same direction. One person should hold the Back Panel while the other person continues to the next step. See FIG 4 6. Align the Left Side Panel with the Floor Panel’s corresponding wood pattern; make sure the Left Side Panel fits flush into the Back Panel. See FIG 5 FIG 5 Assembling Left Side Panel FIG 6 Buckle 7.
. Align the Right Side Panel with the Floor Panel’s corresponding patterns; make sure the Right Panel fits flush into the Back Panel and latch together. See FIG 6 and FIG 7 FIG 7 Assembling Right Panel FIG 8 Placing Floor Heater 9. Place the Floor Heater on the Floor Panel making sure that the Floor Heater is in front of the Bench Heater Panel slots. Please note there is a pre-cut small hole under the Bench Heater Panel which is provided for the Floor Heater cord.
FIG 9 Connecting Cord FIG-10 Installing Bench 11. Align the Front Panel with the Floor Panel’s corresponding patterns; make sure the wood pattern is flowing in the same direction. Next, latch the Front Panel with the Left and Right Side Panels respectively. Note: Be cautious with the glass door to avoid breakage. See FIG 11. FIG 11 Assembling Front Panel FIG 12 Installing Roof Cover 12.
. FIG-13 Slip cords/wires through corresponding holes FIG-14 Connecting cords/wires connectors 13. Connect all the wires and connectors to the corresponding outlets on the Roof Panel. Please be sure all the plugs are connected snug and tight. See FIG-14. Next, pull down the cords/wires of the power plugs of the speakers, temperature sensor, control panel and CD player through the hole near the fan on the Roof Panel. 14. The CD Player will already be mounted in its wood housing box.
15. Connect the control panel connectors. See FIG 16 FIG 16 Connecting control panel connectors 16. Make sure all steps are completed correctly. Plug in the power cord to your wall outlet. the control panel to confirm that the control panel is responding. proceed in putting the Roof Cover onto the Roof Panel. Turn on the sauna at If the control panel responds accordingly, t hen Make sure to pull the power cord through the corresponding hole in the Roof Cover.
Sauna Operation 1. Precautions a. Please make sure your wall outlet meets the specifications required. Failure to meet the requirements may cause safety risks. The average used temperature range is between 118ºF – b. Set the temperature and time to a comfortable level. 122ºF. The average sauna session is approximately 20 – 30 minutes. You must pre-heat sauna room to the desired temperature before entering. Note: If the ambient temperature is below 72℉, the sauna will take longer to pre-heat.
d. Press the button to turn the light ON. If you want to use the Color Light Therapy System: 1. While the interior light is ON, press and hold down the notice “2n” in the LED display. button for 2 seconds. This indicates you are in the “light” mode. You will If you do not press any buttons for approximately 15 seconds, the “2n” will change back to the Timer mode. 2. While the “2n” is displayed, you can now turn the exterior light ON/OFF by pressing the in the button section of the control panel.
Warnings 1. Safety precautions a. To avoid fire, do not dry clothes or leave any towels in the sauna room. b. Do not install the sauna near water, near a bathtub, near a shower, in a wet basement, or near a swimming pool. c. To prevent burns or electric shocks, do not touch or use metal tools on the protective material covers of the heat emitter panels. d. When replacement parts are required, be sure they meet the specified requirements of the manufacturer.
3 Infrared Heater not heating up The heater is broken Replace heater panel The wire junction or the heater’s wire Check that the connections are sung is not connected and tight The temperature sensor is broken check the connection of the temperature sensor The circuit board or the relay is not replace the circuit board working 4 Odor from the sauna Power supply problem Power supply may need to be replaced 5 Light bulb is not working Light bulb is burned out Remove burned out light bulb an
Maintenance: Cleaning Do not use liquid cleaners or aerosol cleansers inside the sauna. Use plain water and a soft cloth for cleaning. sauna. Unplug the sauna from the wall outlet before cleaning. Do not use benzene, alcohol, or strong cleaning chemicals in or on the NOTE: Any chemical that can damage wood or be absorbed into the wood will damage the sauna. Transportation and storage 1. Avoid exposure to rain, snow or other strong weather elements. 2. Do not store in damp environments.
Limited Lifetime Warranty *Limited Lifetime Warranty: Golden Designs, Inc. warranties the heating elements and electronics against defects in material and workmanship for the life of the product from the original date of purchase. This sauna is for INDOOR use only. Placing your sauna outdoors will VOID this warranty. Any damage due to exposure to outdoor elements such as rain, snow, sun, wind or extreme temperatures will not be covered by this warranty.
consequential costs, expense or damages - which may include the removal of permanent deck or other custom fixtures or the necessity for crane removal - arising directly or indirectly out of the use or inability to use the product. Any implied warranty shall have duration equal of the applicable warranty stated above. Under no circumstances shall Golden Designs, Inc. or any of its representatives be held li able for injury to any person or damage to any property, however arising.
WARRANTY CARD Congratulations on your purchase of an Infrared Sauna from Golden Designs, Inc. Please take the time to complete the following Warranty Card and mail it back to: Golden Designs, Inc. 1920 Proforma Ave Ontario, CA 91761 Please include a copy of your sales receipt showing date of purchase as this will serve as proof of purchase. Warranty will be VOID if the following warranty card is not mailed back within 60 days of purchase date along with proof of purchase.