FR-100 MINI HAND HELD TYPE 5 BANDS COMMUNICATIONS RECEIVER USER'S OPERATION MANUAL
CONTENTS PAGE ■ DESCRIPTION OF FEATURES ........................................................... 4 -DISPLAY PANEL FEATURES ............................................................. 4 -TOP PANEL FEATURES .................................................................... 5 -SIDE AND BACK PANEL FEATURES .................................................6 -FRONT PANEL FEATURES .........................................................….. 7 ■ BATTERY PACK INSTRUCTION ......................................
■ DESCRIPTION OF FEATURES ● Display Panel Features 1. " " Indicates the narrow "FM" mode has been selected. 2. " " Indicates the “AM” mode has been selected. 3. " " Indicates the wide “FM” mode for broadcasting radio has been selected. 4. " " (Battery indicator) Indicates batteries are getting low. If the battery level is lower than the standard point, Battery Level Indicator will twinkle. 5. " " Indicates that memory mode has been activated 6. " " (A.b.c.d.E) Indicates the operating band 7.
● Top Panel Features 1. Power On/Off, Volume Turn the Volume switch clockwise to the turn power on and set desired volume. Turn the Volume button anti-clockwise to turn the power off. When the power is on, the lastly used frequency per mode and band is displayed on the LCD. 2. Antenna This antenna provides good receiver performance given its overall size. 3. Phone Jack Let the user listen to the conversation in privacy.
● Side and Back Panel Features 1. MO/SET (Monitor) 1) MO(Monitor) Press the "MO(Monitor)" button shortly in the receiving mode to open the squelch control. This is useful when a weak signal is to be monitored. Re-Activate : Press the MO button one more time. 2) SET To fix each selection. Press this button. 2. (Lamp) Press the " " button, the lamp will stay on for four seconds, after that It will turn off automatically.
● Front Panel Features 1. ▲(Channel up) button Press the "▲" button to move to a higher frequency than is currently shown on the LCD. To access Up scanning process, press the "▲” button over two seconds. In the event that during the scanning processing, the radio stop for 3 seconds at a receiving frequency and re-starting the scanning processing unless you press any buttons. - If you want to stop scanning process, simply press any button - The scanning processing is available per band. 2.
2) Change of Frequency step FR-100 has 5KHz,8.33KHz(Air), 10KHz,12.5KHz, 20KHz, 25KHz, 50KHz,100KHz, 200KHz and 1MHz frequency step. To change the frequency step, press the “SEL” button longer than 2 seconds. With Up/Down button, you can select the frequency step which you want. To fix the frequency step, press the “MO/SET” button. If the “MO/SET” key will not be pressed over 4 seconds, current frequency step will be fixed automatically.
4.
FR-100 has five bands. A b C d E Band : 66 - 88 NFM(Narrow FM) Band : 88 - 108 WFM (Wide FM Broadcasting) Band : 108 - 136 AM Band : 136 - 174 NFM Band : 420 - 470 NFM 25KHz Step 100KHz Step 10KHz Step 20KHz Step 12.5KHz Step To select the wanted band, pressing “BAND” button. Each band will be accessed with following turn. When you press the “BAND” button, the last used frequency per band will be displayed on the LCD. 5.
Frequency Up/Down” button” - Press “MEM” button longer than 2 seconds - The LCD will show the empty memory channel location - Select the memory location where you wish to store the selected frequency by pressing "▲ or ▼" buttons till the Memory Channel Indicator shows that location. - Press the “SET” button. Note : 1. If the “MO/SET” key will not be pressed over 4 seconds, current frequency will be stored automatically. 2.
The desired frequency can be directly entered using the cursor function in normal mode. The desired frequency however should be in the allocated frequency range of the band. To enter the frequency directly using cursor function, follow the example: 1) Example of Frequency selection Frequency desired is 145.4650 MHz on the VHF Band. - Press the "BAND" button till the VHF FM Band is indicated, then press “CUR” button. the first digit of the frequency display will start to flash.
■ BATTERY PACK INSTRUCTION 1. Press down the battery lock button on the bottom side of the radio.( ) 2. Open the battery cover on the back side of the radio.( ) 3. Install the battery as like shown.( ) 4. Put on the battery cover.( ) 5. Press the battery lock button upward to lock the battery case. To supply the power, use the DC charge adapter. CAUTION : Please use only rechargeable battery with DC charge adapter.
■ SPECIFICATION 1. GENERAL FREQUENCY ------------------------ A BAND : 66MHz TO 88MHz B BAND : 88MHz TO 108MHz C BAND : 108MHz TO 136MHz D BAND : 136MHz TO 174MHz E BAND : 420MHz TO 470MHz FREQUENCY GENERATION --- PLL SYNTHESIZER FREQUENCY STABILITY -------- +/- 15ppm OPERATING TEMPERATURE -- -10 TO +55 POWER SOURCE ------------------ INT : 4.5V EXT : 4.5 TO 6.0V MODULATION ----------------------- F3E, A3E IMPEDANCE ------------------------- 50 ohm DIMENSIONS ------------------------ 58(W) x 103(H) x 26.
Maycom B/D, 280-5, Seoksu 2-Dong, Manan-Gu, Anyang-City, Kyoungki-Do, Korea Tel : 82 31 470-7700 Fax : 82 31 470-7799 Office) Factory) Tel : 82 31 470-7740 Fax : 82 31 470-7798 Home page : http://www.maycomcoltd.com http://www.emaycom.com e-mail : maycom@maycomcoltd.com maycom@emaycom.
