Installation Guide

ManualsBrandsMaykke ManualsBathLiverpool 30 in. H x 24 in. W Wall Mirror in Light Gray

PRODUCT INSTALLATION

VANITY MIRROR

PRODUCT INSTALLATION

REV. 111915

MIRROR

PRE-INSTALLATION

Tools Required

Safety

goggles

Phillips screwdriver

Drill

Hardware Included

Part Description Quantity

AA Anchor / Wood screw 2

BB Metal wire 1

WHAT IS COVERED

All products in the package carry a One-Year Limited Lifetime warranty. This warranty applies only to the original

purchaser and to the original installation of the product.

WHAT IS NOT COVERED

Damage caused during moving or during installation is not a defect or warranty issue and will not be considered as such.

This warranty does not cover product failure caused by abusive treatment, surface scratches, misuse, neglect or damage

due to handling or faulty installations. All wood naturally ages, darkens, changes in color, and mellows over time due

to exposure to light. While this color change is imperceptible from day to day, it may be signicant over a long period of

time, or due to amount of light the wood is exposed to. Imperfections such as small surface splits, small dark holes or

darker mineral streaks are natural and are not considered defects.

Toll free Customer Assistance at 877.659.2128

M - F: 7:30AM - 4:30PM PST.

LIMITED LIFETIME WARRANTY

MODEL: DT7024

DT7224

DT7724

DT7824

DT7936

AA BB

Summary of content (6 pages)

PAGE 1
VANITY MIRROR PRODUCT INSTALLATION MIRROR MODEL: DT7024 DT7224 DT7724 DT7824 DT7936 LIMITED LIFETIME WARRANTY WHAT IS COVERED All products in the package carry a One-Year Limited Lifetime warranty. This warranty applies only to the original purchaser and to the original installation of the product. WHAT IS NOT COVERED Damage caused during moving or during installation is not a defect or warranty issue and will not be considered as such.
PAGE 2
VANITY MIRROR PRODUCT INSTALLATION PRE-INSTALLATION (continued) Package Contents A Part A Description Quantity Mirror 1 INSTALLATION 1 Measuring dimensions □□ Determine the ideal location for your new vanity mirror. □□ Usually the mirror should be a minimum of 1 in. above the faucet. □□ Lay the mirror (A) face down on a towel to prevent scratches to the glass or wood frame. □□ Measure the length and width of your mirror (A). Record the measurements. PRODUCT INSTALLATION 2 REV.
PAGE 3
VANITY MIRROR PRODUCT INSTALLATION INSTALLATION (continued) 2 Positioning the mirror □□ Place the mirror (A) into the ideal position and mark the corners from the top left and bottom right of the mirror (A). □□ Make sure the mirror (A) is centered to the vanity. 3 Threading the wire Loose lark’s head shows pattern of threading □□ Thread the wire (BB) through the eyelet of one D-ring to the opposite D-ring and back to the beginning point.
PAGE 4
VANITY MIRROR PRODUCT INSTALLATION INSTALLATION (continued) 4 Hanging the mirror □□ Measure 6 in down from the top mark on the wall and 12 in right from the same mark. □□ Make sure the mirror (A) is at least 1 in. above the faucet. □□ Drill a pilot hole. This will be used to anchor a wood screw (AA) to hang the mirror (A). □□ Hang the mirror (A) by the metal wire (BB). PRODUCT INSTALLATION 4 REV.
PAGE 5
VANITY MIRROR PRODUCT INSTALLATION CARE AND CLEANING WOOD DOORS AND PANELS Dust cabinets frequently with a soft, lint-free cloth. You may dampen the cloth with water or with a spray-type dust remover. Clean up spills immediately. Use a clean, damp cloth if necessary. Wipe dry with another clean soft cloth. Cloth is better than paper towels for this purpose.
PAGE 6
VANITY MIRROR PRODUCT INSTALLATION This page is intentionally left blank PRODUCT INSTALLATION 6 REV.