Manual

ManualsBrandsMayline ManualsFurniture120 Degree Starter

When ordering components, specific color and/or size information may be required.

Contact a Mayline Customer Service Representative. 1-800-822-8037

NOTE: Please count and inspect all pieces before disposing of any carton or packing materials.

COMPONENTS:

Item # QTY. DESCRIPTION PART #

1 3 LEG A8043**

2 3 BEAM ASSEMBLY A8139**

3 6 TROUGH SIDE B8438**

4 3 PAN B8439**

5 1 CORNER CONNECTOR Call~~**

6 3 WORK SURFACE Call~~**

ASSEMBLY INSTRUCTIONS

TRANSACTION 120° STARTER

Item # QTY. DESCRIPTION PART #

7 0/12 ACCESS PANEL L7006**

8 3 CENTER ACCESS PANEL L7286**

9 3 OUTER LEG PANEL B8258**

10 3 INNER LEG PANEL B8219**

11 3 CORNER CONNECTOR

INNER LEG PANEL B8440**

** Denotes Color Code

~~Denotes Size

HARDWARE BAG (PART No. A8146)

* for individual item, order that part number

Item # QTY DESCRIPTION PART #

E1 6 TUBE INSERT, 5/16-18 T139*

E2 6 GLIDE Q608*

E3 3 GLIDE Q630*

E4 38 SCREWS #10-32 x 1/2" X204*

E5 12 WASHER, EXT STAR #10 W38*

E6 44 SCREW #10 x 3/4 X11*

E7 7 PLUG, SQUARE HOLE F782*

E8 6 SLAM LATCH Q643*

E9 9 BUSHING F764*

E10 18 RATCHET FASTENER F483*

E11 12 PINE TREE CLIP F529*

Summary of content (7 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS TRANSACTION 120° STARTER NOTE: Please count and inspect all pieces before disposing of any carton or packing materials. COMPONENTS: Item # 1 2 3 4 5 6 QTY. 3 3 6 3 1 3 When ordering components, specific color and/or size information may be required. Contact a Mayline Customer Service Representative. 1-800-822-8037 DESCRIPTION LEG BEAM ASSEMBLY TROUGH SIDE PAN CORNER CONNECTOR WORK SURFACE PART # Item # A8043** A8139** B8438** B8439** Call~~** Call~~** 7 8 9 10 11 QTY.
PAGE 2
WORK SURFACE HARDWARE TA120TS HARDWARE BAG (PART No. A8151) Item # QTY DESCRIPTION * for individual item, order that part number PART # E12 8 ANGLE, MOUNTING B8267* E13 17 SCREWS #10-32 x 1/2" X204* E14 10 DOWEL PIN.
PAGE 3
NOTE: If the desired configuration utilizes one or more adders, substitute Adder Legs (TADAL**) where desired. 1. Install tube inserts (E1) into legs (1). NOTE: Substitute Adder Leg (TADAL**) for one Leg (1) when final configuration utilizes multiple adders. 2. Screw glide (E2) into inserts. 3. Screw glides (E3) into nuts on the underside of center connector (5).
PAGE 4
NOTE: If using a power pole, install power pole to corner connector (5) at this time and position as desired. Use instruction sheet and hardware included with Power Pole product. NOTE: If installing a table without access panels (7 & 8), proceed to Step 5. 4. Attach mounting angles (E12) to trough side (3) using screws (E13) in locations shown. 5.
PAGE 5
NOTE: If installing a table without access panels (7 & 8), proceed to Step 8. 7. Attach mounting angles (E12) to beam assembly (2) using screws (E13) 8. Install beam assembly (2) from above. Position beam with end notch as noted in detail at right. Place beam (2) between legs (1) and corner connector (5) by tipping the beam into the leg flange notch. Secure beam (2) with screws (E4) and washers (E5). 9. Insert bushing (E9) into trough side (3) and corner connector (5). 10.
PAGE 6
11 Lay pan (4) onto inside trough side flanges (3). Secure pan (4) to trough sides (3) using pine tree clips (E11). 12. Install slam latch (E8) into inner leg panel (10 & 11) as shown. 13. Insert tabs in the bottom of inner leg panel (10 or 11) into slots in leg (1) or corner connector (5). Rotate inner leg panel (10 or 11) up so that slam latch catches flange on pan (4). 14.
PAGE 7
15. Insert dowels (E14) into holes in access panels (7 & 8) as shown below. 16. Lay access panels (7 & 8) onto table frame so that dowels engage holes in mounting angles. 17. Insert spacers (E15) between access panels and work surfaces as shown (2 per access panel). 18. Position work surfaces and secure with screws (E5). Remove spacers.