Glass Front Vender by Maytag DN5000 Beginning Production Run 8063BY DN3000 Beginning Production Run 8292DB Manufactured by Dixie-Narco, Inc. P.O. Drawer 719 Williston, SC 29853-0719 803-266-5001 fax: 803-266-5049 Visit us on the web: www.dixienarco.com 803,903,030.
GENERAL INFORMATION Table of Contents GENERAL INFORMATION .............................................................................................................................3 VENDER SAFETY PRECAUTIONS ...............................................................................................................................................3 PRODUCT IDENTIFICATION.....................................................................................................................................
GENERAL INFORMATION GENERAL INFORMATION PHYSICAL CHARACTERISTICS DN5000 VENDER SAFETY PRECAUTIONS Please read this manual in its entirety. This service information is intended to be used by a qualified service technician, who is familiar with proper and safe procedures to be followed when repairing, replacing, or adjusting any Dixie-Narco vender components.
INSTALLATION & SETUP The Dixie-Narco Coca-Cola Glass Front Vender is designed utilizing the latest technology. 60 Hertz). The cabinet serial plate also indicates the Amperage of the vender. The vender must be plugged in to its own properly rated single phase, alternating current outlet with its own circuit protection (fuse/circuit breaker). RECEIVING INSPECTION DO NOT USE AN EXTENSION CORD. INSTALLATION & SETUP DO NOT STORE THE VENDER OUTSIDE. THIS MACHINE IS FOR INDOOR USE ONLY.
INSTALLATION & SETUP The Vender will support the following MDB card readers: Multi-Drop Card Readers (Domestic) Debitek Smart Card - MDB Danyl Schlumberger (At publication swipe reader had not been tested) Fage MDB Diebold Systems AT&T Campus Wide VMC LTD Jofemar Evend.net PLACING THE VENDER ON LOCATION The Coca-Cola Glass Front Vender is for INDOOR USE ONLY. It should be kept out of direct sunlight and away from any heat source.
INSTALLATION & SETUP glass door for clear viewing of all products. The machine is set up with: 5 Trays, 9 columns or 6 columns each, 8 products per column. Maximum capacity for DN5000 is 15 cases (360 items) of 20 oz. Product and DN3000 is 10 cases (240 items) of 20oz. product. INSTALLATION AND SET UP INSTRUCTIONS Open the service door on the right side using the key provided in the coin return cup, or if shipped with a locking clip, remove the clip and install the lock.
PROGRAMMING PROGRAMMING COCA-COLA EVS GLASS FRONT PROGRAMMING METHOD April 2000 NORMAL MODE: In normal mode, on power up display will show software installed in vender, then change to POS message or decimal point and / or vend price. When money is inserted, the display indicates the total amount of the deposit. The keys on the keypad are used to select the product.
PROGRAMMING “VENDMECH” - Vend Mechanism Summary Errors Press key number 4 and the display will show the following: - “COLJAM#”, where # is the column number detected jammed. Press key number 1 will return to “VENDMECH” if all vend mech errors have not been cleared. If all vend mech errors have been cleared the next error mode will be displayed, or “NONE” if there are no errors. Press key number 1 will return to “ERROR”.
PROGRAMMING “BILL VAL” - Bill Validator Summary Errors Press key number 4 and the display will show one of the following: - “BILLCOMM”, indicating a bill validator communication error. (No communication for more than 5 seconds) - “BILLFULL”, indicating the bill stacker is full. - “BILL MOT”, indicating a defective motor in the validator. - “BILL JAM”, indicating a bill jam in the validator. - “BILL ROM”, indicating a check sum error. - “BILLOPEN”, indicating an open stacker.
PROGRAMMING “REFRIG” - Refrigeration Summary Errors Press key number 4 and the display shows one of the following: - “TEMPSENS”, indicating the temperature sensor is defective or unplugged. - “TOO COLD”, indicating the cabinet temperature is 3 0 F below lower limit. - “TOO HOT”, indicating the cabinet temperature is 3 0 F above upper limit. - “NO COOL”, indicating the cooling system has failed to decrease temperature 10 F per hour while the compressor is running.
PROGRAMMING “TESTMODE” - TEST ROUTINE This function allows you to diagnose different functions of the vender. Press key number 4 and the display will show “TESTVEND”. Press key number 2 or 3 to scroll through the test routines available. Press key number 1 to return to “TESTMODE”. “TESTVEND” - Vend Testing This function allows you to test vend each column. Press key number 4 and the display will show “COL A1”. Press key numbers 2 or 3 to scroll through the columns available to run in motor test.
PROGRAMMING * “CASH” - CASH COUNTER ROUTINE This function will show the user the vender historical total cash counted and the resettable cash counted for each selection for the vender. Press key number 4 and “CASH”/”######.##” will show on the display where the 8"#” characters are the historical total cash counters that have been recorded. Note: Leading zeros are not displayed. Example: Display flashes “CASH”, then “262500”. This is $2625.00 historical total cash.
PROGRAMMING “STS PROG” – SPACE TO SALES ROUTINE This function allows you to change the space to sale settings. Press key number 4 and “OPTION#” or “CUST STS” will show on the display, which indicates the current space to sales option. For the 7 options available, see list below. Press key number 2 to scroll through the options. Press key number 4 with the desired option showing on the display to save that option and return to “STS PROG”.
PROGRAMMING * “CONFIG” - MACHINE CONFIGURATION This function allows the user to access and change the programming of the following machine configuration settings. Note: This routine is lockable when using a data collection device. If you press key number 4 and the display shows “LOC”, this means configuration setting changes will not be allowed. If “CON 1” is displayed, then configuration setting changes will be allowed. “LOC” can only be enabled or disabled through DEX interrogation.
PROGRAMMING CON 6 - Configuration Switch 6 - Reserved This code is reserved for future use. Press key number 2 to scroll to “CON 7”. CON 7 - Configuration Switch 7 - Save Credit This code is used to determine how long a credit will be saved. C7 0 will save the credit for five minutes. CON 7 1 will save the credit indefinitely. Press key number 4 and “CON 7 #” will be displayed, with the “#” flashing. Press key number 2 or 3 to scroll between CON 7 0 and CON 7 1.
PROGRAMMING *”CHANGE” - CORRECT CHANGE ONLY CONTROL ROUTINE This function is used to allow consumer overpay, set a correct change value, and set an unconditional acceptance value. Press key number 4 will enter “CONOVER#”. “CONOVERX” - Allow Consumer Overpay This function allows the vender to vend with the risk of not being able to return the full amount of change. This function has to be turned on to be able to allow consumer overpay.
PROGRAMMING *”LANGUAGE” - LANGUAGE ROUTINE This function is used to set the language that will be used for display messages. Note: This does not change the menu prompts. Press key number 4 and the display will show the language currently set in the controller. Press key number 2 or 3 to scroll through the languages available.
PROGRAMMING “DST” - Daylight Saving Time Setting This function is used to set the preferred daylight savings time setting. Press key number 4 will display the current setting. Press key number 2 or 3 to scroll through the “DST” options listed: - “OFF”, no daylight savings time changes made. - “AUSTRAL”, Australian rules - Set forward 1 hour at 1:00 am on the first Sunday in October; Set backward 1 hour at 1:00 am on the last Sunday in March.
PROGRAMMING “STOP HR” - Stop Hour and Minute Setting This function is used to set the hours and minutes to stop light conservation and can be set in the same manner as Start Hour and Minute Setting. Press key number 1 to return to “STOP TIM”. Press key number 1 to return to “LIGHTING”. Press key number 2 to scroll to next routine. *”REFRIG” - REFRIGERATION ROUTINE This function is used to electronically control the refrigeration operations of the vender. Press key number 4 will enter “ENABLE X”.
PROGRAMMING “DEGREES” - Degree Fahrenheit / Celsius Setting Routine This function is used to set the degree reading to Fahrenheit (DEGREESF) or Celsius (DEGREESC). Press key number 4 and “DEGREESX”, where the current setting (X) will be blinking. Press key number 2 or 3 to scroll between DEGREESF and DEGREESC. Press key number 4 with the display blinking the setting you wish to use. Press key number 1 to return to “DEGREES”. Press key number 2 to scroll to “SETPOINT”.
PROGRAMMING “STRT DAY” - Day of Week Start Setting This function is used to set the day(s) of the week to start selection blocking. Press key number 4 and “XXXXXX#” will show on the display, where XXXXXX will be the day of the week (i.e. MONDAY, TUEDAY, WEDDAY, THUDAY, FRIDAY, SATDAY, SUNDAY, EVR DAY) and # is 0 = disable, 1 = enable. With the display showing the day you wish to set press key number 4. The # will start blinking. Press key number 2 or 3 to scroll between “XXXXXX0” and “XXXXXX1.
PROGRAMMING “LIGHTX” - Lighting / P.O.S. Display Control This function is used to turn the lights (if supported) and P.O.S. Display Message off during selection blocking period 1. 0 = disable or on; 1 = enable or off. Press key number 4 and the “#” will start flashing. Press key number 2 or 3 to scroll between “LIGHT0” and “LIGHT1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “LIGHTX”. Press key number 1 to return to “SELBLCK1”.
PROGRAMMING *”DISCOUNT” - DISCOUNT SETTING ROUTINE This function is used to set the day(s) and times to allow discount prices. Press key number 4 and ENABLE X will show on the display. “ENABLE X” - Discount Setting Enable Routine This function is used to disable discounting “ENABLE 0” or enable discounting “ENABLE 1”. Press key number 4 and the current “ENABLE X” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLE 0” and “ENABLE 1”.
PROGRAMMING “OVERRIDE” - MANUAL SWITCH OVERRIDE ROUTINE This function is used to allow a key switch to override some of the settings stored for normal operations. This function can be programmed to control one or several of the following features: Free Vend Enable, Selection Blocking, Discount Pricing, and Lighting Control. Press key number 4 and the display will show “FREE X”. Press key number 2 or 3 to scroll through the override routines available. Press key number 1 to return to “OVERRIDE”.
PROGRAMMING “REFRIG X” - Refrigeration Control Override Routine This function is used to override “REFRIG”, if it is being used. “REFRIG 0” = disabled and “REFRIG 1” = enabled. Press key number 4 and “#” will start flashing. Press key number 2 or 3 to scroll between “REFRIG 0” and “REFRIG 1”. Press key number 4 with the display showing the setting you wish to use. Display will return to “REFRIG X”. Press key number 1 to return to “OVERRIDE”. Press key number 2 to scroll to “RVNDMECH”.
PROGRAMMING “VND RATE” - Universal Satellite Device (USD) Vend Rate Routine This function is used to set the vend rate (0-255). Press key number 4 and the current vend rate (0-255) will show on the display. Press key number 2 to increase, or 3 to decrease the number in single digit increments. NOTE: A rate of “0” disables the USD. All other rates, #, will cause a vend command every #’th local vend.
PROGRAMMING To enable, with “HEALTH” on display press key number 4 will enter “ENABLE X”. “ENABLE X” – Health Enable Routine This function is used to enable the Health Protection feature. When enabled, protected selections will only be allowed to vend if health constraints listed above are met. Press key number 4 and the current “ENABLE” setting will be displayed. Press key number 2 or 3 to scroll between “ENABLED 0” and “ENABLED 1”. Press key number 4 with the display blinking the setting you wish to use.
PROGRAMMING COCA-COLA PROGRAMMING METHOD QUICK REFERENCE MENU PROMPTS Select Button 1: Select Button 2: Select Button 3: Select Button 4: Abort / Cancel (will return to previous menu prompt or to normal door open mode) Scroll Up (forward in menu) Scroll Down (backward in menu) Enter / Save / Clear (allows you to enter a specific prompt, save what you have programmed, or clear the error prompts) NO COOL - Failed System **ERROR - Error Readout Routine ** VENDMECH - Vend Mechanism Error COLJAM# - Column Jam
GENERAL MAINTENANCE The most important facets of proper care and maintenance of your machine are the electrical power supplied to it, leveling, and cleanliness of the machine. POWER The machine must be connected to a dedicated 120 VAC, 15 Amp circuit (U.S. and Canada). CAUTION: REMOVE POWER TO THE AC DISTRIBUTION BOX WHEN ANY ELECTRICAL COMPONENTS ARE CONNECTED / DISCONNECTED FOR TESTING OR REPLACEMENT.
MAJOR COMPONENT DESCRIPTION MAJOR COMPONENT DESCRIPTION 110 VAC AC DISTRIBUTION BOX 110 VAC 15 Amp Outlet (110 VAC) Provides power to refrigeration unit. Transformer (T1) Provides 24 Volt and 12 Volt (center tap) power to the Controller Board. Fuse (Top) Fuse (Bottom) REFRIGERATION UNIT 10 Amp, 32 Volt, SloBlo; protects 24 Volt input to Controller Board from secondary of T1. 2 Amp, SloBlo; protects 12 Volt input to Controller Board from secondary, center tap of T1.
MAJOR COMPONENT DESCRIPTION UNIVERSAL (KO) BOARD (0077-8272CB & Higher) 31 of 90
PROGRAMMING UNIVERSAL (KO) BOARD (prior to 0077-8272CB) 32 of 90
PROGRAMMING MACHINE BOARD (0077-8272CB and Higher) 33 of 90
PROGRAMMING MACHINE BOARD (prior to 0077-8272CB) 34 of 90
MAJOR COMPONENT DESCRIPTION WIRING DIAGRAM (9 Column) 35 of 90
PROGRAMMING Wiring Diagram (6 Column) 36 of 90
TROUBLESHOOTING 8 7 2 1 2 1 2 3 4 5 2 6 2 3 2 4 2 5 2 6 7 8 Thread stud Hex Nut Side Panel Ground Chassis Ground Lead from Power Input Toothed Terminal Panel Mount Receptacle Ground Choke AC DISTRIBUTION BOX T8 7 6 2 5 2 1 2 1 2 3 4 5 2 3 4 2 6 7 Thread stud Hex Nut Side Panel Ground Chassis Ground Lead from Power Input Toothed Terminal Panel Mount Receptacle Ground AC DISTRIBUTION BOX NON-T8 37 of 90
TROUBLESHOOTING Troubleshooting ASD DISPLAY 38 of 90
TROUBLESHOOTING CONTROL BOARD ISSUES 39 of 90
TROUBLESHOOTING CONTROL BOARD ISSUES (CONTINUED) 40 of 90
TROUBLESHOOTING CONTROL BOARD ISSUES (CONTINUED) 41 of 90
TROUBLESHOOTING CONTROL BOARD ISSUES (CONTINUED) 42 of 90
TROUBLESHOOTING COIN MECH ISSUES 43 of 90
TROUBLESHOOTING COIN MECH ISSUES (CONTINUED) 44 of 90
TROUBLESHOOTING COIN MECH ISSUES (CONTINUED) 45 of 90
TROUBLESHOOTING COIN MECH ISSUES (CONTINUED) 46 of 90
TROUBLESHOOTING COMPRESSOR ISSUES 47 of 90
TROUBLESHOOTING COMPRESSOR ISSUES (CONTINUED) 48 of 90
TROUBLESHOOTING SOLENOIDS 49 of 90
TROUBLESHOOTING SOLENOIDS (CONTINUED) 50 of 90
TROUBLESHOOTING CONVEYOR ISSUES 51 of 90
TROUBLESHOOTING Display reads vending but the elevator does not move. Check port door switch. Open and close the port door. Is port door switch properly secured? Does the port door close completely? Correct or replace port frame and retest. YES YES YES Check harness connection and VMC. Is harness connected at VMC Replace port door switch. Does elevator function? NO Clear the obstruction and retest with service door open. NO NO Connect harness and retest. YES 1 Finished.
TROUBLESHOOTING FAN MOTOR ISSUES 53 of 90
TROUBLESHOOTING KEYPAD ISSUES 54 of 90
TROUBLESHOOTING KEYPAD ISSUES (CONTINUED) 55 of 90
TROUBLESHOOTING LIGHT ISSUES 56 of 90
TROUBLESHOOTING LIGHT ISSUES (CONTINUED) 57 of 90
TROUBLESHOOTING TEMP SENSOR ISSUES 58 of 90
TROUBLESHOOTING ICE / FROST ON EVAPORATOR CONDENSATE ON OUTSIDE OF PRODUCT DOOR COMPRESSOR RUNS CONTINUOUSLY 59 of 90
PARTS PARTS INDEX Machine Front View ............................................................................. pgs. 61 & 62 Cabinet Detail ...................................................................................... pgs. 63 & 64 Service Door (Front) ............................................................................. pgs. 65 & 66 Service Door (Inside) ........................................................................... pgs. 67 & 68 Tray Assembly ...............................
PARTS MACHINE FRONT VIEW 61 of 90
PARTS MACHINE FRONT VIEW ITEM 1A-1 1A-2 1B-1 1B-2 1C–1 1C–2 2 3A DN5000 PART # 800,102,29x.x1 800,101,87x.x1 800,102,36x.x1 800,102,02x.x1 626,055,30x.x3 800,102,12x.x1 801,814,58x.x1 801,306,49x.x1 3B 801,306,48x.x1 3C 801,305,70x.x1 3D 800,303,56x.x1 3E 800,303,41x.x1 3F 801,814,52x.x1 4A 801,305,65x.x1 4B-1 900,502,49x.x1 4B-2 800,503,38x.x1 4C 805,410,96x.x1 5 W334 6A 432,052,50x.x4 6B 432,050,73x.x3 6C 801,303,85x.x1 6D 900,801,06x.x1 6E 900,301,97x.x1 6F 900,302,01x.x1 7 626,030,19x.
PARTS CABINET DETAIL 63 of 90
PARTS CABINET DETAIL ITEM 1A 1B 1C 2A 2B 3A 3B 3C 3D 4A 4B 5A 5B 5C 6 7 8 DN5000 PART # 626,060,00x.x3 626,060,30x.x3 637,050,50x.x3 626,070,25x.x3 626,070,62x.x3 626,070,08x.x3 626,070,63x.x3 626,070,67x.x3 626,070,71x.x3 626,070,19x.x3 626,070,64x.x3 626,020,05x.x3 626,020,12x.x3 626,020,42x.x3 626,070,51x.x3 804,100,77x.x1 801,812,41x.x1 DN3000 Part # 636,060,20x.x3 TBD TBD SAME SAME NA NA SAME SAME SAME SAME 636,020,05x.
PARTS SERVICE DOOR FRONT 65 of 90
PARTS DN5000 & DN3000 SERVICE DOOR (FRONT) CGF (Coke Glass Front) PART NUMBER 626,054,10x.x3 626,054,40x.x3 637,051,40x.x3 626,050,10x.x3 805,025,32x.x1 801,305,75x.x1 803,859,34x.x1 626,054,00x.x3 626,052,40x.x3 637,050,90x.x3 801,810,69x.x1 626,050,36x.x3 624,050,48x.x3 803,863,03x.x1 W453-2 626,031,80x.x4 804,918,26x.x1 626,050,03x.x3 626,050,36x.x3 626,010,60x.x4 805,701,24x.x1 801,519,13x.x1 801,518,14x.x1 801,518,18x.x1 801,519,14x.x1 801,507,34x.x1 901,503,06x.x1 901,503,09x.x1 901,503,05x.
PARTS SERVICE DOOR (INSIDE) 67 of 90
PARTS DN5000 & DN3000 SERVICE DOOR (INSIDE) ITEM PART NUMBER PART DESCRIPTION 1 626,050,20x.x3 Assembly Chute, Coin Insert 2 626,050,30x.x3 Assembly Coin Return 3 626,050,04x.x3 Coin Return Button Bracket 4 626,050,05x.x3 Coin Return Button Rocker 5 801,807,25x.x1 Coin Return Push Button 6 801,903,13x.x1 Bushing, .51Dx625 Hole 7 900,502,19x.x1 Roller Pin 8 900,900,90x.x1 Roller Pin Retainer (not shown) 9 901,701,07x.x1 Coin Return Spring 10 801,903,76x.x1 Red Display Filter 11 901,001,46x.x1 Stand Off, .
PARTS TRAY ASSEMBLY 69 of 90
PARTS TRAY ASSEMBLY ITEM DN5000 PART # DN3000 PART # 1 626,071,30x.x3 636,070,20x.x3 2 626,070,09x.x3 635,070,01x.x3 3 801,903,83x.x1 SAME 4 804,300,16x.x1 SAME 5 801,519,29x.x1 SAME 6A 801,903,82x.x1 SAME 6B 801,812,79x.x1 SAME 6C 901,701,08x.x1 SAME 7 801,401,98x.x1 801,402,21x.x1 8 W485-1 SAME 9 622,070,04x.x3 SAME 10 W789 SAME 11 W218 SAME 12 W398 SAME 13A D334 SAME 13B 800,101,94x.x1 SAME 14 901,901,00x.x1 SAME 15 See List SAME 15A 801,812,69x.x1 SAME 15B 801,812,81x.x1 SAME 16 804,913,74x.
PARTS AC DISTRIBUTION BOX (DOMESTIC SHOWN) 1A-2 prior to 049-8234 1A-2 prior to 049-8234 1A-1 049-8234 & Up 1A-1 049-8234 and up 71 of 90
PARTS DN5000 & DN3000 AC DISTRIBUTION BOX ITEM 1A - 1 1A - 2 1A - 3 1B 1C 2 3 4 5 6 7 8A 8B 9A PART NUMBER 626,031,90x.x3 626,030,40x.x3 637,050,10x.x3 626,030,70x.x3 626,031,30x.x3 804,920,02x.x1 W658 W659 W662 804,913,62x.x1 804,915,54x.x1 803,860,28x.x1 803,860,83x.x1 803,853,22x.
PARTS ELEVATOR 8 2 7 2 9 2 73 of 90
PARTS DN5000 & DN3000 ELEVATOR ITEM PART NUMBER PART DESCRIPTION 1 805,202,37x.x1 Elevator with Motor Assembly 2A 804,100,99x.x1 Lower Motor Limit Switch 2B 801,306,03x.x1 Bracket, Home Position Aluminum 3 801,813,09x.x1 Upper Limit Switch Assembly 4 804,101,04x.x1 Lower Limit Switch Magnet 5 804,501,21x.x1 Elevator Motor 6 801,306,11x.x1 Washer, Aluminum 7 801,401,97x.x1 Belt Tensioner Spring 8 801,813,14x.x1 Elevator Drive Belt 9 804,800,84x.x1 Assembly Pillow Block 10 801,306,03x.
PARTS CONVEYOR 75 of 90
PARTS CONVEYOR ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19A 19B 19C 19D 19E 20 21 DN5000 PART NUMBER 626,070,50x.x3 626,070,81x.x3 804,915,81x.x1 804,915,75x.x1 801,813,08x.x1 801,812,65x.x1 801,401,94x.x1 626,050,33x.x3 626,070,31x.x3 626,070,83x.x3 801,803,03x.x1 626,070,22x.x3 626,070,22x.x3 626,070,21x.x3 626,070,72x.x3 804,501,16x.x1 800,503,09x.x1 801,812,42x.x1 801,812,85x.x1 801,812,84x.x1 804,915,81x.x1 801,812,35x.x1 800,902,62x.x1 800,303,36x.x1 DN3000 PART NUMBER 636,070,00x.
PARTS LIGHTING B2A A6A B1A B3A B2A A1A A7 B2B A5 B1B A4B A7 B3B A4B A4A 77 of 90
PARTS ITEM A1A DN5000 PART # 626,072,10x.x3 A1B 626,070,80x.x3 636,070,30x.x3 A1C A2A 626,031,00x.x3 626,072,20x.x3 636,071,20x.x3 636,070,80x.x3 A2B A3A A3B A4A 626,070,90x.x3 804,920,53x.x1 804,915,67x.x1 804,400,58x.x1 NA SAME NA SAME A4B A4C A4D A4E A5 A6A A7 A8 A9 A10A A10B A11 804,400,44x.x1 804,400,58x.x1 804,400,71x.x1 626,030,90x.x3 801,903,90x.x1 804,700,79x.x1 NA 804,700,69x.x1 NA 904,800,41x.x1 804,101,07x.x1 626,070,61x.x1 801,904,35x.x1 801,904,06x.x1 801,904,06x.
PARTS REFRIGERATION 79 of 90
PARTS DN5000 & DN3000 REFRIGERATION ITEM PART NUMBER PART DESCRIPTION 1 626,041,60x.x4 Domestic Kit – Refrigeration System 2000C-A 115/60 1A 626,040,00x.x3 Refrigeration System 2000C-A 115/60, Domestic/Japan 1B 626,041,00x.x3 Refrigeration System 2020C-A, Export 1C 626,041,90x.x3 Refrigeration System 2030C-A, Export Korea 2A 626,040,60x.x3 Compressor Assembly 115 / 60, Domestic/Japan 2B 626,041,30x.x3 Compressor Assembly 220-240/50, Export 2C 626,042,30x.
PARTS ELECTRONICS 81 of 90
PARTS DN5000 & DN3000 ELECTRONICS ITEM PART NUMBER PART NUMBER NEW REMANUFACTURED 1A 626,056,30x.x4 TBD 1B 626,030,21x.x3 SAME 1C 626,050,48x.x3 SAME 627,050,31x.x3 SAME 2A 626,032,10x.x3 TBD 2B 626,032,20x.x3 TBD 2C - 1 626,030,36x.x3 SAME 2C - 2 801,904,16x.x1 SAME 2D - 1 626,030,37x.x3 SAME 2D - 2 622,050,32x.x3 SAME 2E 801,903,87x.x1 SAME 3A 804,919,93x.x1 SAME 3B 804,914,86x.x1 SAME 4 804,100,77x.x1 SAME 5 804,100,99x.x1 SAME 6 804,101,04x.x1 SAME 7 804,101,05x.x1 SAME 8 804,915,84x.
PARTS HARNESSES ITEM PART NUMBER 804,913,74x.x1 Tray Harness 8 Column 804,920,34x.x1 Tray Harness 6 Column 2A 804,920,54x.x1 2B 804,915,65x.x1 3 4 804,915,81x.x1 804,915,69x.x1 *Door Lighting Hartness T8 Electronics (049-8234 and higher) *Door Lighting Harness (prior to 049-8234) Conveyor Harness Relay Control Harness 5 804,919,66x.x1 6 7 804,915,64x.x1 804,915,76x.x1 8 804,915,62x.x1 9A 804,920,63x.x1 9B 804,915,59x.x1 9C - 1 9C - 2 10 11A 804,913,77x.x1 804,920,70x.x1 804,915,72x.
PARTS LABELS / DECALS / MISC. CGF (Coke DGF (Dasani Glass Front) Glass Front) ITEM PART NUMBER PART NUMBER PART DESCRIPTION 1 803,859,74x.x1 Bottom Glass Door Decal 2 803,859,72x.x1 803,866,39x.x1 Top Glass Decal 3 803,859,71x.x1 803,866,43x.x1 Cabinet, Side Decal 4 803,857,26x.x1 Selection Label 5 803,856,15x.x1 Asset / Property Tag Coca-Cola Company 6 803,868,29x.x1 Warning: DO NOT TILT Label, Tri Lingual 7 803,859,73x.x1 803,866,42x.x1 Conveyor Decal 8 803,853,21x.
PARTS SCREWS AND NUTS 85 of 90
PARTS SCREWS & NUTS ITEM PART NUMBER PART DESCRIPTION A1 900,301,70x.x1 Screw, Phil Pan Swage Form #6-32x3/8″ A2 900,301,64x.x1 Screw, Phil Pan Swage Form w/ Washer #8-32x1/2″ A3 900,301,83x.x1 Screw, Phil Pan Swage Form #10-32x5/16″ A4 900,301,50x.x1 Screw, Phil Pan without Washer, #8-18x1/2″ A5 900,301,97x.x1 Screw, Phil Pan Swage Form #8-32x1/4″ A6 900,300,47x.x1 Screw, Vend Motor, #4-24x3/4″ Single Switch A7 900,301,82x.x1 Screw, Vend Motor, #4-24x1-16 ″ Double Switch A8 900,301,61x.
PARTS SCREWS & NUTS (Continued) ITEM PART NUMBER PART DESCRIPTION B6 900,800,49x.x1 Hex Nut, #6-32 B7 900,800,51x.x1 Elastic Stop Nut, #8-32 B8 900,800,81x.x1 Hex Nut, 8-32 B9 900,902,37x.x1 Push Nut, Acorn Type B10 900,801,02x.x1 Hex Nut, 5/16-18 B11 800,801,13x.x1 Nut, Self Clinching 5/16-18 B12 800,303,38x.x1 SCREW,8-18x1/2 (Bottom Skirt) Part numbers subject to change with out notice.
PARTS WASHERS / BOLTS / MISC HARDWARE 88 of 90
PARTS WASHERS , BOLTS, AND MISC. HARDWARE ITEM C1 C2 C3 C4 C5 C6 C7 C8 C10 C11 C12 C13 C14 C15 C16 C17 C18 PART NUMBER 900,700,60x.x1 901,303,77x.x1 901,503,06x.1 901,503,08x.x1 900,700,36x.x1 900,700,89x.x1 900,700,02x.x1 900,700,62x.x1 900,700,83x.x1 900,700,08x.x1 801,902,48x.x1 W884 W398 W218 801,518,03x.x1 W861 900,701,15x.x1 900,701,05x.x1 PART DESCRIPTION Washer, Delrin .047 Thick 3/8″ ID x 5/8 OD Washer, Door Hinge Washer, Flat #2949 (T-Handle) Washer, Hex #29.
PARTS WASHERS , BOLTS, AND MISC. HARDWARE (continued) ITEM H1 H2 H3 H4 H5 H6 H7 H8 H9 H10 H11 H12 PART NUMBER 900,902,13x.x1 900,901,89x.x1 900,401,09x.x1 901,503,07x.x1 900,900,90x.x1 900,902,18x.x1 801,807,01x.x1 901,806,77xx.1 902,100,29x.x1 801,903,80x.x1 901,502,53x.x1 801,903,87x.x1 PART DESCRIPTION Christmas Tree Clip #354280307-00 Tinnerman Clip, Fan Shroud (C5207-014-3B) Grommet, Bk.