Installation guide

iNSTALLATiON REQUIREMENTS
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with any tools
listed here.
All Installations
Tools needed:
P ers
Phillips
screwdriver
5A8"and 1/4"
nut drivers or
hex sockets
Measuring tape
or ruler
10"adjustable wrench_
that opens to f_
11/8 (2.9 cm)
Flat-blade
screwdriver
Utility knife
UL Listed/CSA _
Approved twist-on U Ij
wire connectors*
Small level
*Must be the proper size to connect your household wiring to 16
gauge wiring in dishwasher
Other useful items you may need:
Flashlight Bath towel
Parts supplied:
IDiainhaSec'amps(2)D'ai_(1arge and 1 sma )
"Green
#10 x 1/_,,
Phillips:head
screw_
Make sure all these parts are included in the literature package.
Parts needed:
90 _EIbo_ fitting With _ Teflon_ tape orpip--joint "
%" N'P.T. external threads compound
(the other end must fit your
Water Supply line) ___ )
I
Other parts you may also need:
I.......
1V2 -2 I Side mounting kitl Masking or I
(38,1-5 cm)Ifor solid surlace I du
Screw:type countertops
clamps (3 maximum) 1 (Part8212560)Number Ij
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
In addition, for first=time installations
Tools needed:
• 1 " 3
with ½, F4
and 11/2"hole
saw bits
Parts needed:
,w
CopPer tubing (%" See "Electrical Requirements" section
O.Disuggested) or For Direct Wire: For Power Supply
flexible braided Use UL L Sted/ Cord: use UL
water sUPPly lin e CSA ApproVed listed power
supply cord
kit
Strain relief marked for use
if(f#(" "_'_'_'_ tofit% (2,2 cm) with dishwasher
! NumBer(USegro m302797met P a:rt
not included)
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
wa rra nty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277)is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
. easy access to water, electricity and drain.
. convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
. square opening for proper operation and appearance.
. cabinet front perpendicular to floor.
, level floor. (if floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.