Installation Instructions

ManualsBrandsMaytag ManualsAppliances7.4 cu. ft. Commercial-Grade Residential Dryer in White

W11045669A

W11045670A-SP

DRYER SAFETY ......................................................................... 2

INSTALLATION REQUIREMENTS ............................................. 3

Tools and Parts ...................................................................... 3

LOCATION REQUIREMENTS .................................................... 4

ELECTRICAL REQUIREMENTS ................................................ 6

INSTALL LEVELING LEGS ......................................................... 7

ELECTRICAL CONNECTION .................................................... 7

VENTING ................................................................................... 13

Venting Requirements ......................................................... 13

Plan Vent System ................................................................. 14

Venting Kits .......................................................................... 15

Install Vent System .............................................................. 15

Connect Vent ........................................................................ 16

LEVEL DRYER .......................................................................... 16

COMPLETE INSTALLATION CHECKLIST .............................. 17

REVERSE DOOR SWING (OPTIONAL) ................................... 17

TROUBLESHOOTING .............................................................. 19

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

27" WIDE MODELS – U.S.A. ONLY

Para obtener acceso al manual de uso y cuidado en español, o para obtener información

adicional acerca de su producto, visite: www.maytag.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo

y de serie dentro de la cavidad superior de la puerta.

Table of Contents

INSTALLATION NOTES

Date of purchase: ________________________________

Date of installation: _______________________________

Installer: _______________________________________

Model number: __________________________________

Serial number: ___________________________________

Summary of content (20 pages)

PAGE 1
ELECTRIC DRYER INSTALLATION INSTRUCTIONS 27" WIDE MODELS – U.S.A. ONLY Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.maytag.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. Table of Contents DRYER SAFETY.......................................................................... 2 INSTALLATION REQUIREMENTS.................................
PAGE 2
DRYER SAFETY 2
PAGE 3
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
PAGE 4
Parts needed: Dryer Dimensions Check local codes. Check existing electrical supply and venting, and read “Electrical Requirements” and “Venting Requirements” before purchasing parts. Mobile home installations require metal exhaust system hardware, available for purchase from the dealer from whom you purchased your dryer. For further information, please reference the “Assistance or Service” section of the Use and Care Guide.
PAGE 5
Minimum spacing for recessed area or closet installation Mobile home – Additional installation requirements The dimensions shown following are for the minimum spacing allowed. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for wall, door, and floor moldings. ■■ Additional spacing of 1” (25 mm) on all sides of the dryer is recommended to reduce noise transfer.
PAGE 6
ELECTRICAL REQUIREMENTS If your outlet looks like this: It is your responsibility: ■■ To contact a qualified electrical installer. ■■ To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70 – latest edition and all local codes and ordinances. The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
PAGE 7
INSTALL LEVELING LEGS ELECTRICAL CONNECTION Power Supply Cord 1. Prepare dryer for leveling legs To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. 2. Screw in leveling legs Electrical Connection Options 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-Wire Power Supply Cord Connection” section.
PAGE 8
Power Supply Cord Connection Direct Wire Power supply cord strain relief 1. Attach power supply cord strain relief A B Fire Hazard C Use 10 gauge copper wire. D Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal. Ground wire (green or bare wire) must be connected to green ground connector. Connect remaining 2 supply wires to remaining 2 terminals (gold). Securely tighten all electrical connections.
PAGE 9
4-Wire Power Supply Cord Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. 4-wire receptacle (NEMA type 14-30R) 3. Connect ground wire 4-prong plug A F Connect ground wire (F) (green or bare) of power supply cord to external ground conductor screw (A). Tighten screw. Spade terminals with upturned ends Ring terminals 4. Connect remaining wires 1.
PAGE 10
Direct Wire Connection 1. Remove center screw Direct wire strain relief 1. Attach direct wire strain relief A B B C Remove center terminal block screw (B). 2. Connect neutral wire B C Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL Listed strain relief. Put the threaded section of the strain relief (C) through the hole below the terminal block opening (B).
PAGE 11
4-Wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 4. Connect ground wire 1. Prepare your 4-wire cable for direct connection 1" m) (25 m A 5 (127 " mm ) F Connect ground wire (green or bare) (F) of direct wire cable to external ground conductor screw (A). Tighten screw. Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed.
PAGE 12
Optional 3-Wire Connection 2. Remove center screw IMPORTANT: You must verify with a qualified electrician that this grounding method is acceptable before connecting. 1. Prepare to connect neutral ground wire and neutral wire B E B Remove center terminal block screw (B). 3. Connect neutral wire A B C Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). 2.
PAGE 13
4. Connect external ground wire Rigid metal vent: ■ Recommended for best drying performance and to avoid crushing and kinking. Flexible metal vent: (Acceptable only if accessible to clean) ■ Must be fully extended and supported in final dryer location. ■ Remove excess to avoid sagging and kinking that may result in reduced airflow and poor performance. ■ Do not install in enclosed walls, ceilings, or floors. ■ The total length should not exceed 7 3/4 ft. (2.4 m).
PAGE 14
Clamps: Optional exhaust installations: ■■ Exhaust vent must not be connected or secured with screws Exhaust can be converted out the right side, left side, or through the bottom (4-way vent kit). Each kit includes step-by-step instructions. For ordering information, see “Venting Kits.” ■■ Use clamps to seal all joints. or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape. See “Venting Kits” for more information.
PAGE 15
Venting Kits For more information, call 1-800-344-1274, or visit us at www.maytagreplacementparts.com.
PAGE 16
2. Connect vent to exhaust hood LEVEL DRYER 1. Level dryer Vent must fit over the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location using straightest path possible. Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into interior of vent to secure vent, because they can catch lint. Connect Vent 1. Connect vent to exhaust outlet Check levelness of dryer from side to side.
PAGE 17
COMPLETE INSTALLATION CHECKLIST REVERSE DOOR SWING (OPTIONAL) ❑ NOTE: Magnetized screwdriver is helpful. ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ ❑ Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. Check that you have all of your tools. Dispose of/recycle all packaging materials. Check dryer’s final location. Be sure vent is not crushed or kinked. Check that dryer is level. See “Level Dryer.” Remove film on console and any tape remaining on dryer.
PAGE 18
4. Remove screws from hinges 7. Flip door over Flip door over so handle side is down. Remove screws attaching hinges to door. 8. Attach door hinges 5. Remove screws from door Remove screws at top, bottom, and side of door (six screws). Keep door screws separate from hinge screws as they are different sizes. Holding door over towel on dryer, grasp sides of outer door and lift to separate it from inner door. NOTE: Do not pry apart with putty knife or screwdriver.
PAGE 19
10. Insert screws in hinge holes on dryer cabinet TROUBLESHOOTING See the Use and Care Guide or visit our website and reference “Frequently Asked Questions” to possibly avoid the cost of a service call. NOTE: Two people may be needed to reinstall door. Insert screws into the bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges.