Installation Instruction

ManualsBrandsMaytag ManualsAppliances30 in. 6.7 cu. ft. Double Oven Electric Range with Convection Oven in Fingerprint Resistant Stainless Steel

INSTALLATION INSTRUCTIONS

FREESTANDING ELECTRIC RANGE

WITH DOUBLE OVENS

INSTRUCTIONS D’INSTALLATION

POUR CUISINIÈRE ÉLECTRIQUE AUTOPORTANTE

AVEC FOURS DOUBLES

RANGE SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT:

Save for local electrical inspector’s use.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations électriques.

W10430958B

Table of Contents/Table des matières

RANGE SAFETY .............................................................................1

INSTALLATION REQUIREMENTS .................................................2

Tools and Parts .............................................................................2

Location Requirements ................................................................2

Electrical Requirements - U.S.A. Only .........................................4

Electrical Requirements - Canada Only .......................................5

INSTALLATION INSTRUCTIONS ...................................................5

Unpack Range..............................................................................5

Adjust Leveling Legs ....................................................................5

Install Anti-Tip Bracket .................................................................6

Electrical Connection - U.S.A. Only .............................................7

Verify Anti-Tip Bracket Is Installed and Engaged ......................12

Level Range ................................................................................12

Complete Installation .................................................................13

Moving the Range ......................................................................13

SÉCURITÉ DE LA CUISINIÈRE ...................................................14

EXIGENCES D’INSTALLATION ...................................................15

Outils et pièces ...........................................................................15

Exigences d’emplacement .........................................................15

Spéciﬁcations électriques ..........................................................17

INSTRUCTIONS D’INSTALLATION .............................................17

Déballage de la cuisinière ..........................................................17

Réglage des pieds de nivellement .............................................17

Installation de la bride antibasculement ....................................18

Vériﬁer que la bride anti-basculement

est bien installée et engagée .....................................................18

Réglage de l’aplomb de la cuisinière .........................................19

Achever l’installation ..................................................................20

Déplacement de la cuisinière .....................................................20

Summary of content (20 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FREESTANDING ELECTRIC RANGE WITH DOUBLE OVENS INSTRUCTIONS D’INSTALLATION POUR CUISINIÈRE ÉLECTRIQUE AUTOPORTANTE AVEC FOURS DOUBLES Table of Contents/Table des matières RANGE SAFETY..............................................................................1 INSTALLATION REQUIREMENTS..................................................2 Tools and Parts..............................................................................2 Location Requirements...............................
PAGE 2
WARNING Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved. Do not operate range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults.
PAGE 3
Product Dimensions Cabinet Dimensions Cabinet opening dimensions shown are for 25" (63.5 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface. A freestanding range may be installed next to combustible walls with zero clearance.
PAGE 4
Electrical Requirements - U.S.A. Only If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord. Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all local codes and ordinances.
PAGE 5
Electrical Requirements - Canada Only WARNING ■■ Check with a qualified electrical installer if you are not sure the range is properly grounded. Range Rating* Electrical Shock Hazard Electrically ground range. Failure to do so can result in death, fire, or electrical shock. If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge are in accordance with local codes.
PAGE 6
Install Anti-Tip Bracket WARNING 3. Determine and mark edge of range in the cutout space. The mounting bracket can be installed on either the left side or right side of the cutout. Position mounting bracket in cutout so that right (or left) edge of the bracket is 15/16" (2.4 cm) from the marked edge of the range, as shown. A B Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions.
PAGE 7
Electrical Connection - U.S.A. Only Power Supply Cord Direct Wire WARNING WARNING Electrical Shock Hazard Electrical Shock Hazard Disconnect power before servicing. Disconnect power before servicing. Use a new 40 amp power supply cord. Use 8 gauge copper or 6 gauge aluminum wire. Plug into a grounded outlet. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock.
PAGE 8
Style 2: Direct wire strain relief ■■ ■■ ■■ Use Phillips screwdriver to remove screws and slide cord/conduit plate down and out. Feed the flexible conduit through the strain relief, allowing enough slack to easily attach wiring to the terminal block. ■■ Tighten strain relief screw against the flexible conduit. Position cord/conduit plate as shown in the following illustration. 5. Replace back panel and screws on rear of range. 6.
PAGE 9
5. Use 3/8" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts. 4-wire connection: Power Supply Cord Use this method for: ■■ New branch-circuit installations (1996 NEC) ■■ Mobile homes ■■ Recreational vehicles A In an area where local codes prohibit grounding through the neutral 1. Part of metal ground strap must be cut out and removed. ■■ F B E C A B C D A. 10–32 hex nut B. Ground-link screw C. Line 1 (black) A. Metal ground strap B.
PAGE 10
2. Use 3/8" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. 4-wire Connection: Direct Wire Use this method for: A E ■■ New branch-circuit installations (1996 NEC) ■■ Mobile homes ■■ Recreational vehicles In an area where local codes prohibit grounding through the neutral 1. Part of metal ground strap must be cut out and removed. ■■ D B C A. 10-32 hex nut B. Line 1 (black) C. Ground-link screw A B C D. Neutral (white) wire E.
PAGE 11
4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to XX lbs-in. torque. See Bare Wire Torque Specifications chart. A B C D 3-wire connection: Direct Wire Use this method only if local codes permit connecting ground conductor to neutral supply wire. 1.
PAGE 12
Bare Wire Torque Specifications Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m) Wire Awg Torque 8 gauge copper 25 lbs-in. (2.8 N-m) 6 gauge aluminum 35 lbs-in. (4.0 N-m) 3. Use 3/8" nut driver to connect the bare (green) ground wire to the center terminal block post with one of the 10-32 hex nuts. F A E B C A. 10-32 hex nut B. Line 1 (black) C. Ground-link screw D D. Bare (green) ground wire E. Line 2 (red) F. Terminal lug 4.
PAGE 13
Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check that the range is level. See the “Level Range” section. 5. Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by shipping material. Dry thoroughly with a soft cloth.
PAGE 14
SÉCURITÉ DE LA CUISINIÈRE Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres.
PAGE 15
EXIGENCES D’INSTALLATION Outils et pièces Rassembler les outils et composants nécessaires avant d’entreprendre l’installation. Lire et observer les instructions fournies avec chacun des outils de la liste ci-dessous.
PAGE 16
Dimensions du produit Dimensions du placard Les dimensions de l’espace d’installation entre les placards sont valides pour l’installation entre des placards de 24" (61,0 cm) de profondeur avec plan de travail de 25" (63,5 cm) de profondeur et 36" (91,4 cm) de hauteur.
PAGE 17
Spécifications électriques AVERTISSEMENT Risque de choc électrique Relier la cuisinière à la terre. Le non-respect de cette instruction peut causer un décès, un incendie ou un choc électrique. Si les codes en vigueur le permettent et qu’un conducteur distinct de liaison à la terre est utilisé, on recommande qu’un électricien qualifié vérifie que la liaison à la terre et la taille du conducteur de liaison à la terre sont adéquates et conformes aux prescriptions des codes locaux.
PAGE 18
Installation de la bride antibasculement AVERTISSEMENT 4. Percer deux trous de 1/8" (3,0 mm) qui correspondent aux trous de la bride selon la méthode de montage déterminée. Voir ci-dessous. Montage au plancher A Montage au mur B A B Risque de basculement Un enfant ou une personne adulte peut faire basculer la cuisinière, ce qui peut causer un décès. Fixer la bride antibasculement au plancher ou au mur, conformément aux instructions d'installation.
PAGE 19
3. Si l’arrière de la cuisinière se soulève de plus de ½" (1,3 cm) du plancher sans opposer de résistance, cesser d’incliner la cuisinière et la reposer doucement sur le plancher. Le pied de la cuisinière n’est pas engagé dans la bride antibasculement. IMPORTANT : Si l’on entend un claquement ou un bruit d’éclatement lorsqu’on soulève la cuisinière, cela signifie peutêtre que la cuisinière n’est pas bien engagée dans la bride.
PAGE 20
Achever l’installation 1. Vérifier que toutes les pièces sont maintenant installées. S’il reste une pièce, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée. 2. Vérifier la présence de tous les outils. 3. Éliminer/recycler tous les matériaux d’emballage. 4. Vérifier que la cuisinière est d’aplomb. Voir “Réglage de l’aplomb de la cuisinière”. 5.